587983
10
Zoom out
Zoom in
Previous page
1/60
Next page
Button functions
/ BUTTON
Activate and/or deactivate the unit by enabling the voltage supply to the
unit. The controller performs a self test and then indicates operational
readiness by the flashing of the LED 1 below the display.
Voltage
activated
Automatic
Approx. 1 min.
No voltage present Controller perform-
ing self test
Controller can be
operated
External enable
If a floating contact is used for the external enabling of the unit, the con-
troller shows "OFF" on the display and the display of the decimal places
flashes. The floating contact (Terminal 2-3) has priority for operation over
the controller.
Factory setting: Contact (Terminal 2-3) open = controller on
Possible connection: Contact (Terminal 2-3) closed = controller off
External enable
contact opened
Normal display
Units activated
Display
Unit deactivated
External enable
contact closed
The unit has three modes: Standby mode, summer fan control (cooling
mode), and transition mode (heating mode - only for units with heat
pump function). "StbY" is displayed in standby mode. All fault messages
and anti-frost protection resistors are active. The set cooling and heating
mode is indicated by the LED.
Please note: Changing the parameters can result in the programming of a
changed functional sense of the display!
Mode setting
> 5 sec. > 5 sec.
> 5 sec. > 5 sec.
HEATING MODE
Only KWG
COOLING
MODE
KWL and KWP
Cooling mode
Heating mode
Standby mode
SET value entry, cooling mode
Programming the set values
Using the "SET" button, the set value can be displayed during standby
or cooling mode. To change the set value, the "SET" button is pressed
for about 2 seconds. The display starts to flash. Using the "" or ""
button, the value can be set within the limits defined at the factory (St 02
+ St 03).
St 02 = 9.0°C Minimum set value, cooling mode
St 03 = 20.0°C Maximum set value, cooling mode
Factory setting = 11.0 °C
< 2 sec.< 2 sec. < 2 sec.< 2 sec. ...
Normal
display
Value
opened
Submenu
opened
Close
submenu
Entry of
new set value
< 2 sec.
REMKO KWG
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWG750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWG750 in the language / languages: English as an attachment in your email.

The manual is 7,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWG750

REMKO KWG750 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info