587982
28
Zoom out
Zoom in
Previous page
1/60
Next page
Diaphragm expansion vessel
To prevent pressure fluctuations
during standstills due to
temperature changes, diaphragm
expansion vessels with a nitrogen
filling (moisture-neutral) must be
integrated into the system.
The standard version of the
KWG...P, KWG...SP, KWP...P,
and KWP...SP units include a
diaphragm expansion vessel. The
volume of these diaphragm expan-
sion vessels are designed only for
those units. The system requires an
additional diaphragm expansion
vessel designed for this system.
An individual design is required for
the KWG and KWP units.
The calculation can be performed
with roughly 5 to 10% diaphragm
expansion vessel volume of the
system volume.
The pre-pressure of all diaphragm
expansion vessels must be set on
the system.
Safety valve 6.0 bar
Safety valves limit an operating
pressure that is too high due to ex-
cessive heating or an overfilling of
the operating medium. The valve
outlet requires a free feed into a
drain line. When glycol is used, the
local disposal regulations must be
observed.
The standard version of the unit
includes a safety valve.
Bleeding valves
The unit has manual bleeding
valves. After the filling of the
system, the unit can be bled here
separately. In addition, automatic
bleeding valves must be mounted
at the highest point of the collec-
tive line.
When media containing glycol
are used, glycol-resistant
bleeding valves must be used.
ATTENTION
Capacitors
In order not to transmit the
vibrations of the chiller to the
system parts, we recommend the
use of capacitors to connect the
lines to the unit, in addition to
Victaulic connectors.
Capacitors
Shut-off valve Capacitor
Static
fastening
KWG connection
Shut-off valves
In cold water systems, shut-off
valves with full throughput should
fundamentally be used. For
servicing purposes, the medium
inlet and medium outlet must be
equipped with shut-off valves
(with safety valve, if required).
Circulation pump for KWG and
KWG...SP
For units without a storage tank,
an external circulation pump is
required for the implementation
of the nominal volume flow rate
within the chiller!
Actuation takes place via the ter-
minal strip using a controller of the
chiller.
Incorrectly installed or missing
dirt traps can cause a soiling of
the plate heat exchanger.
ATTENTION
Filling and bleeding connection
A connection for bleeding the
pipelines (especially when water
is used as the medium) should be
provided in the anti-frost-protect-
ed area. When glycol is used, the
local disposal regulations must be
observed.
Dirt trap
A rinsable dirt trap must be in-
stalled in front of the unit inlet.
The mesh size should not exceed
10 meshes/cm². Shut-off valves
should be used upstream and
downstream of the dirt trap.
If the minimum medium volume
flow rate of the system is under-
shot, malfunctions may result.
NOTE
Anti-frost protection (accessory)
A water/glycol mixture is usu-
ally used as the medium of a cold
water system. According to the
glycol type and amount used, the
viscosity changes, the pressure
loss increases, and the dissipated
cooling and/or heating capacity
of the unit decreases. All system
components must be released for
use with glycol.
In general, we recommend that
34% ethylene glycol with in-
hibitors for corrosion protection be
added to the water. This concen-
tration guarantees anti-frost safety
up to –20°C; at lower tempera-
tures, an ice slush that no longer
has a bursting effect arises.
If the medium could come into
contact with drinking water or
food, a toxicologically harmless
medium based on propylene glycol
must be preferred.
REMKO KWG
28
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWG600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWG600 in the language / languages: English as an attachment in your email.

The manual is 7,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWG600

REMKO KWG600 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info