587982
9
Zoom out
Zoom in
Previous page
1/60
Next page
"Cooling Mode" button
Long pressing (>5 seconds)
switches between the cooling
and standby modes.
"Heating Mode" button
(only units with heat pump
function)
Long pressing (>5 seconds)
switches between the heating
and standby modes.
Symbol for compressors 1-6
Indicates the operation (lights
up) of the compressors. If the
LED is flashing, the correspond-
ing compressor is in safety time.
The "Pump" symbol lights up
when the circulation pump is
actuated.
The "Fan" symbol
lights up when the condenser
fan is actuated.
Thawing status LED
(only units with heat pump
function)
The LED indicates the opera-
tion (lights up) of the thawing
cycle during the heating mode
on the air-cooled condenser. If
the LED flashes, the controller
determines the required thaw-
ing time.
Symbol for anti-frost protection
medium heater
This symbol provides informa-
tion on the operating status
of the "anti-frost protection
medium heater" accessory.
"Menu" LED
Lights up when the parameter
level is activated.
Operation of the
iPro controller
The controller has 3 Modi:
1. Summer fan control (cooling
mode)
In cooling mode, the warmer me-
dium temperature is cooled to the
colder set value.
2. Transition mode (heating mode)
(only units with heat pump func-
tion):
In heating mode, the colder me-
dium temperature is heated to the
warmer set value.
3. Readiness mode (standby)
In standby mode, the safety equip-
ment is active and an operating
mode is not set.
"Menu" button
With this button, you can ac-
cess the function menu or set
the time and date.
"SET" button
With this button, you can select
a set value or parameter.
"" button
Pressing briefly can switch
between medium inlet, medium
outlet, condensation pressure,
and evaporation pressure. A
value can also be lowered.
"" button
Pressing briefly can switch
between medium inlet, medium
outlet, condensation pressure,
and evaporation pressure. A
value can also be raised.
"" and "SET" buttons together
Simultaneously pressing the
"" and "SET" buttons (>5
seconds) permits a change to
parameter levels 1 through 3.
"" and "SET" buttons together
Simultaneously pressing the
"" and "SET" buttons (<2
seconds) lets you leave param-
eter levels 1 through 3.
"" and "SET" together for
longer than 5 seconds
Simultaneously and longer
pressing the "" and "SET"
buttons (>5 seconds) enables
manual thawing (only units
with heat pump function).
"Vset" LED
Lights up when the dynamic set
value is activated.
Cooling mode LED
This LED indicates the selected
cooling mode.
Heating mode LED
(only units with heat pump
function)
This LED indicates the selected
heating mode.
"Cir1" symbol
Describes the specified value for
cooling circuit 1.
"Cir2" symbol
Describes the specified value for
cooling circuit 2.
"Flow!" symbol
Describes a medium volume
flow rate that is too low or too
high or no medium pressure.
General alarm LED
Indicates the respective fault in
combination with the code.
Value display (red display)
The value display shows current
values.
Parameter display (yellow dis-
play)
The parameter display shows
current values or parameters.
"°C" and "F°" symbol
Indicates which temperature
unit is shown in the value
display.
"Time" symbol
Indicates a value in a unit of
time.
"Bar" and "PSI°" symbol
Indicates which pressure unit is
shown in the value display.
+
+
Control panel of the IPS400D / IPC108E controller
+
bar
°C
F
PSI
Flow!
Vset
menu
Cir1 Cir2
menu
SET
IPS400DIPro
SMALL
bar
°C
F
PSI
Flow!
Vset
menu
Cir1 Cir2
menu
SET
IPS400D
IPro
SMALL
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWG600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWG600 in the language / languages: English as an attachment in your email.

The manual is 7,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWG600

REMKO KWG600 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info