726822

REMKO KWE serie 150-180-220-250-300-320-370-440 Manual

32
Zoom out
Zoom in
Previous page
1/60
Next page
n The unit must be kept upright when trans-
porting to a higher elevation.
1
Fig. 15: Vertical unit transport
1: Pick-up point
n Check the contents of the packaging for com-
pleteness and check the unit for visible trans-
port damage. Report any damage immediately
to your contractual partner and the shipping
company
.
n Select an installation location which allows air
to freely flow through the air inlet and outlet
(see section "Minimum clearances").
n Do not install the unit in the immediate vicinity
of devices which generate intensive thermal
radiation. Installation in the vicinity of thermal
radiation reduces the unit output.
n Lift the unit only at intended lifting points.
Never place the medium or refrigerant piping
under load.
n The medium connection lines, valves and con-
nections must have vapour density insulation.
If necessary, also insulate the condensate
drainage line. In dual systems with cooling and
heating modes, the requirements of the current
Energy Savings Ordinance (EnEV) are to be
complied with.
n Seal off open lines to prevent dirt getting in and
never kink or crimp the lines.
n Avoid unnecessary bends. This minimises the
pressure loss in the lines.
n Install all electrical wiring in accordance with
applicable DIN and VDE standards.
n Ensure the electrical cables are properly con-
nected to the terminals. Otherwise there is a
risk of fire.
n Comply with all regulations governing structural
and building requirements and conditions with
regard to the installation site.
n In the selection of the installation site, pay
attention to the site itself and to any possible
acoustic reflection from surrounding units.
n T
o avoid the transmission of vibrations to the
installation site, the units must be installed on
vibration absorbing material or on vibration
decoupled foundations. In doing so, make sure
that the lines are also vibration decoupled
n If the installation site must fulfil special sound
emission requirements, these must be realised
on-site when appropriate adjustments can be
made. In these cases, please consult an
appropriate acoustics expert.
Wall openings
n W
e recommend that the inside of the opening
be padded or lined for example with a PVC
pipe to prevent damage to the lines.
n After installation, the wall opening should be
closed off by the customer with a suitable
sealant. Do not use substances containing lime
or cement!
Installation materials
The unit is fastened on vibration dampers (acces-
sories) to the floor by means of bolts. The carrying
capacity of the bracket and the wall must be taken
into account when fastening to the wall.
Selecting the installation location
The unit is designed for horizontal installation on a
base in outdoor areas. The installation site must be
level, flat and firm. The unit should also be secured
to prevent it from tipping over
. The unit can be
installed outside as well as inside a building. For
external installation, please observe the following
instructions to protect the unit from the influence of
the weather.
Rain
The unit should be at least 10 cm off the ground
when mounted on the roof or ground. A floor
bracket is available as an accessory.
Increasing the installation height will also increase
the heating capacity generated by the heating /
cooling unit (only HP function).
REMKO KWE
32
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWE serie 150-180-220-250-300-320-370-440 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWE serie 150-180-220-250-300-320-370-440 in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWE serie 150-180-220-250-300-320-370-440

REMKO KWE serie 150-180-220-250-300-320-370-440 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info