587908
14
Zoom out
Zoom in
Previous page
1/44
Next page
14
REMKO GPM
Resetting
The fault (interlock) is indicated by
the red LED on the unit lighting
up, a triangle flashing on the
temperature control display and
the fault code “Reset heating”
being displayed.
For fault code analysis and
resetting, see chapter “Fault
message display” (page 18) and
“Type of faults” (pages 11 + 37).
A reset must only be
performed 20 seconds after
switching off the unit.
ATTENTION
The changeover switch at
the front of the unit with
temperature control ATR-6
must always be set to winter
operation d.
NOTE
The temperature control ATR-6
can display possible system faults
and supply diagnostic information.
Display:
The display is completely blank.
Meaning:
The buffer capacitor is discharged
as it was without charge for more
than 5 hours.
Restore the power supply and wait
until the display lights up.
The time, day and required
room temperatures must be
reprogrammed.
The buffer capacitor is fully
charged within about 1 hour.
All parameters necessary for
operation of the unit are stored
indefinitely on the control board.
Only the day and time as well as
the required on and off program
need to be reprogrammed.
The temperature control requires
no particular maintenance.
The temperature control ATR-6
is microprocessor-controlled and
intended for convenient room
temperature control as well as for
diverse unit settings and status
displays.
Features:
week program with timer
3 different temperature settings
per day possible, T1, T2 and T3
temporary cancellation of the
set temperature
automatic and manual mode,
timer program
frost protection mode 5°C
permanently in OFF state
automatic output control
according to heat demand
current status display
display of faults or malfunctions
remote reset button
operation without batteries
power reserve 5 hours
non-polarised two-wire
connection
Checking the board hardware
configuration
The jumper NTC/VAN must be
located on NTC and the CR switch
must be set to ON (towards the
inner part of the board), see
diagram below.
This configuration is necessary to
ensure the correct function of the
NTC1 sensor.
Jumper NTC
CR switch
ON
NOTE
All unit parameters can only
be changed in conjunction
with the electronic
temperature control ATR-6.
Temperature control ATR-6
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO GPM 55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GPM 55 in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO GPM 55

REMKO GPM 55 User Manual - German - 44 pages

REMKO GPM 55 User Manual - Dutch - 44 pages

REMKO GPM 55 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info