Manual REMKO GPM 25 (page 31 of 44) (English)

587906

Zoom out

Zoom in

1/44

Check the electrodes for correct

seating (see diagram).

It is important that the monitoring

electrode [IO] is located tangential

to the ignition burner head and is

not located within the same.

The ignition electrode [Z] must

discharge towards the outside

edge of the ignition burner at

an adequate distance to the

monitoring electrode.

2) Checking the chimney and

supply air pipes

Visually inspect all pipes and

connecting pieces.

Any dirt deposits that have

accumulated on the end piece

of the supply air pipe must be

removed.

3) Checking and cleaning the

Venturi tube

Remove dirt deposits at the

entrance of the Venturi tube with a

brush or other suitable implement.

Ensure that no dirt falls in to the

Venturi tube.

4) Checking the gas supply

pressure

Ensure that the pressure upstream

of the gas valve corresponds to the

value prescribed for the respective

type of gas.

This check must be carried out

with the unit switched on at

maximum output.

5) Checking the ﬂ ame monitoring

device

With the unit in heating mode,

close the gas valve and ensure that

fault F1 is indicated. Open the gas

valve again, reset and wait for the

unit to restart.

6) Checking the safety

thermostat(s)

This check must be carried out

with the unit operating in heating

mode.

- Heat the thermostat sensor using

a hot air gun or similar until fault

F2 is indicated.

- Allow the thermostat sensor(s) to

cool down and reset the unit.

- This check must be carried out on

all thermostats in the unit.

Maintenance

2-3 mm

In order to ensure maximum

performance and a long service

life of the units, several checks

must be made once a year and in

any event before the start of the

heating season.

1) Check the condition of the

ignition and monitoring

electrodes as well as that of the

ignition gas burner.

2) Check the condition of the

supply air and chimney pipes as

well as the end pieces.

3) Check the Venturi tube for

clogging.

4) Check the heat exchanger for

fouling.

5) Check the gas pressure

upstream of the gas valve.

6) Check the function of the ﬂ ame

monitoring device.

7) Check the safety thermostat(s).

8) Check the ionisation ﬂ ow (> 2

microamperes)

1) Checking the electrodes

Dismantle the ignition burner

completely and clean the gas

system and gas nozzle with

compressed air.

Check the ceramic coating on the

electrodes for intactness.

Carefully remove any oxide

deposits on the metal part of the

electrodes with a very ﬁ ne emery

cloth.

For steps 1, 2, 3 and 4, the

mains and gas supply to

the unit must always be

interrupted.

Steps 5, 6, 7 and 8 are carried

out with the unit in heating

mode.

NOTE

We reserve the right to make changes to dimensions and design in the interest of technological advances.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GPM 25 in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO GPM 25

REMKO GPM 25 User Manual - German - 44 pages

REMKO GPM 25 User Manual - Dutch - 44 pages

REMKO GPM 25 User Manual - French - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

REMKO GPM 25 Manual

Product: