587906
26
Zoom out
Zoom in
Previous page
1/44
Next page
26
REMKO GPM
Electrical connection
Electrical connection of the units
must be made by authorised
specialists (power company
approved) in accordance with the
pertinent regulations.
A main/emergency switch
must be provided at any easily
accessible location within sight
of the unit and protected against
unauthorised use. The switch must
disconnect the unit from the mains
supply in all poles with a minimum
contact opening of 3 mm.
The main/emergency
switch must only be used in
emergency situations or after
extended periods of non-use.
If this switch is used to switch
off the unit during operation,
the electric fresh air fan
cannot cool the combustion
chamber. This can cause
damage to the unit.
ATTENTION
The unit must be provided
with a line-side multipole
disconnector with suitable
electrical protection.
The cable cross-section must
be minimum 1.5 mm².
ATTENTION
The units must be connected
polarised to the mains supply
cable.
Mains supply 230V/50Hz,
minimum cross-section of mains
supply cable 1.5 mm
2
.
Legend rear wall:
= Connector
= Connector socket
= Cable entry fittings
= Unit temperature sensor
Connecting the temperature control ATR-6 to the control board
Connect the supplied temperature control connector to the locally
installed bus cable, disconnect the two-pin connector [CN] with resistor
from the control board and reconnect the fitted connector with bus
cable.
Electronic temperature
control ATR-6
Control board
ConnectorCN
JA
NEIN!
B
S
B = Bus cable
S = Electric cable
We reserve the right to make changes to dimensions and design in the interest of technological advances.
The use of a multipole
cable simultaneously for
temperature control and mains
supply must be avoided due to
electromagnetic interference.
NOTE
Phase and neutral conductors
must not be confused
during connection under
any circumstances as the
flame monitoring device will
interrupt operation of the unit
for safety reasons.
Fault F1 is indicated.
NOTE
NO
YES
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO GPM 25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GPM 25 in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO GPM 25

REMKO GPM 25 User Manual - German - 44 pages

REMKO GPM 25 User Manual - Dutch - 44 pages

REMKO GPM 25 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info