587587
25
Zoom out
Zoom in
Previous page
1/36
Next page
Winterregelung
Zum Anschluß der Leitung
(Bild 10) gehen Sie wie folgt vor:
1. Demontieren Sie den
Gerätedeckel.
2. Entfernen Sie die sich beim
Anschluß befindliche
Seitenwand.
3. Wählen Sie den Querschnitt der
Anschlußleitung gemäß den
Vorschriften aus.
4. Führen Sie die beiden Leitungen
durch die Kantenschutzringe
des feststehenden
Anschlußbleches.
5. Klemmen Sie die Leitungen ge-
mäß des Anschlußschemas an.
6. Verankern Sie die Leitung in der
Zugentlastung und bauen Sie
das Gerät wieder zusammen.
9 Anschluß des Außenteils
Für die ordnungsgemäße Funktion
der Anlage bei niedrigen Außen-
temperaturen dürfen die Arbeits-
bereiche des Kältekreises nicht
über- bzw. unterschritten werden.
Die eingebaute Winterregelung
ermöglicht es die Arbeitsbereiche,
auch bei Außentemperaturen von
bis zu –15 °C, konstant zu halten.
Die Winterregelung bewirkt eine
stufenlose Anpassung der Motor-
drehzahl des Verflüssigerventilators
in Abhängigkeit vom Betriebsdruck
der Anlage und der Außentempe-
ratur. Aus diesem Grund kann z. B.
im Winter die Drehbewegung des
Ventilators im Kühlbetrieb vollstän-
dig aussetzen.
Die Regelplatine regelt die Aus-
gangsspannung für den Ventilator,
in Abhängigkeit von der durch
die zwei Jumper (JP) eingestellten
Regelhysterese.
Die Regelung besteht aus einer Re-
gelplatine in einem Gehäuse sowie
einem Temperatursensor (Bild 11).
Der Sensor erfaßt die Lufteintritt-
stemperatur des Verflüssigers.
Temperatursensor Gehäuse der
Regelplatine
11 Regelungskomponenten
12 Verstellung der Regelhysterese
MdV (FVS) VmD (EPB)
JP 1 10 JP 5 20
JP 2 15 JP 6 30
JP 3 20 JP 7 40
JP 4 25 JP 8 50
Verstellung der Regel-
hysterese durch die Jumper
VmD (EPB) = Ventilatormaximal-
Drehzahl
VmD ist die maximale Ventilator-
drehzahl des Lüfters. Sie wird auch
als Effektives Proportional Band
(EPB) bezeichnet (Bild 12).
MdV (FVS) = Mindestdrehzahl
Ventilator
MdV ist die Bauart bedingte Min-
destdrehzahl des Ventilators bei
einer 35 %igen Ausgangsspan-
nung der Regelplatine. Sie wird
auch Fixe Ventilator Spannung
(FVS) bezeichnet (Bild 12).
Ausgangsspannung
100 % (230 V)
35 % (ca.80V)
VmD
20 VmD
30 VmD
40 VmD
50
MdV
25 MdV
20 MdV
15 MdV
10
Temperatur (°C)
-5 0 5 10 15 20 25 30 35 40 45 50
10 Anschluß der Leitung
Netzzuleitung
Steuerleitung Innengerät A
Steuerleitung
Innengerät B
Steuerleitung
Innengerät C
Zug-
entlastungen
Beispiel: GD 335
25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO GD335 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GD335 in the language / languages: German as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info