794472
11
Zoom out
Zoom in
Previous page
1/24
Next page
5 Commissioning the unit
One person, who has been adequately trained in
the handling of the unit, should be tasked with the
operation and monitoring of the unit.
The units are equipped with a 3-stage operating
switch.
Fig. 3: Operating switch
0: Off
1: Ventilation
2: Heating
1. Move the operating switch to the “0” position.
2. Connect the unit's power plug to a properly
installed 16 A (ELT 10-HT), or 32 A (ELT 18-
HT) mains socket.
WARNING!
The electrical connection for the units must be
made at a separate feed point with a residual
current device in accordance with VDE 0100,
Section 55.
Operating mode settings
The operating mode settings can be selected using
a switch or a rotary selector switch.
However, a room thermostat is always required for
operation.
In position “1” only the fan becomes active. This
adjustment can also be changed without a room
thermostat.
No operation takes place in position “0”.
In position “2” the fan and the heating elements
become active. This setting is only permitted with
an electric room thermostat.
Heating with a special purpose HT room ther-
mostat or duct thermostat (accessories)
The units operate fully automatically and according
to the room temperature.
1. Pull out the strapping plug [2].
2. Connect the plug [3] of the relevant thermo-
stat to the thermostat socket [1] on the unit.
3
1
3. Place the probe in a suitable position
according to the type of thermostat used. The
thermostat probe must not be located directly
in the warm air flow and must not be placed
directly on the cold floor.
4. On the room thermostat, set the temperature
required for the application at hand.
5. Move the operating switch to the “2”
(Heating) position.
GREEN indicator light on!
Operating lights
1 32
1: Yellow = HT mode
2: Green = max. heating capacity
3: Red = STB malfunction
Adjust the air outlet temperature
Upon start-up, set the fan speed to the maximum
setting.
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ELT10-HT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ELT10-HT in the language / languages: English as an attachment in your email.

The manual is 4.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ELT10-HT

REMKO ELT10-HT User Manual - German - 24 pages

REMKO ELT10-HT User Manual - Dutch - 24 pages

REMKO ELT10-HT User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info