587886
17
Zoom out
Zoom in
Previous page
1/20
Next page
17
Secondary air setting
(Setting the nozzle stock)
Proceed as follows to preset the secondary air:
Use the adjusting screw 1 to adjust the nozzle 2 to the
value you want.
1
2
Counter clockwise (-) = lower scale values
increased pressure behind the air flow plate
lower performance range
Clockwise (+) = higher scale values
lower pressure behind the air flow plate
upper performance range.
SLV 11 und SLV 33
SL 44
Counter clockwise (+) = higher scale values
reduced pressure behind the air flow plate
upper performance range
Counter clockwise (-) = lower scale values
increased pressure behind the air flow plate
lower performance range
.
4
3
Adjusting the air flap
Proceed as follows to adjust the air flap:
1. Loosen the knurled nut 4.
2. Rotate the adjustment screw 3 accordingly.
3. Keep the following in mind:
Right rotation = less air
Left rotation = more air
4. After the adjustment is completed, retighten the ad-
justment screw with the knurled nut.
Additional Information
à If the air flap is completely open and the flame emits
smoke or flickers, use the secondary air setting to
lower the pressure behind the air flow plate.
à It might be necessary to open the air slide plate even
further.
Air flap
The adjustment screw 3 is used to set the required
quantity of air.
The air flap is opened or closed until the soot profile dis-
plays an oil-free colour “0 - 1”.
Setting the pump pressure
For initial burner operation and after each time the
burner is serviced, the oil pressure must be adjusted
and/or checked.
Proceed as follows to adjust the pump pressure
1. Remove the stopper on the “P” measuring connec-
tion.
2. Mount the oil manometer.
3. Open all shut-off fittings in the oil supply.
4. Switch the burner on.
5. Set the required oil pressure in accordance with the
size of the nozzle and the unit performance.
6. Switch the burner off.
7. Disassemble the oil manometer.
8. Replace the stopper and its seal.
Important Information
à
The forced-air burner may only be put into operation by
trained personnel
.
à All specifications only serve as presets and must be
set or adjusted after the waste gas has been ana-
lysed.
à Exhaust emissions must be restricted in accordance
with the ordinance on small furnace systems.
G
Never operate the pump without fuel!
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO CLK150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO CLK150 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO CLK150

REMKO CLK150 User Manual - German - 20 pages

REMKO CLK150 User Manual - Dutch - 16 pages

REMKO CLK150 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info