587886
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
Before Starting
Prior to initial operation, check the unit for any visual de-
fects on the control and safety devices, that the unit has
been installed correctly and that it has been properly
connected to the mains.
Observe the following points:
à Install the unit in a stable position.
à Make sure that air is supplied for combustion.
à Make sure that the air can be sucked in and be ex-
hausted freely.
à Avoid overpressure and underpressure in the room
where the unit has been installed.
à Make sure that enough fuel is supplied.
à Please note: the multifilex oil preheater will only func-
tion properly if voltage is supplied to the unit for a
longer time prior to initial operation.
à Use only clean heating oil or diesel.
Do not use bio diesel.
Additional information
The waste gas values of the oil-burner are to be
checked and properly adjusted by authorised personnel
to ensure compliance with local requirements.
Paraffin accumulation at low outside temperatures
A sufficient amount of heating oil must be able to flow
freely even when temperatures are low.
à Paraffin can accumulate even at temperatures below
5 °C.
à Appropriate measures must be taken to prevent this.
Use winterised heating oil or winter diesel.
Connection to the power supply
The units are operated with 400 V / 3~N / 50 Hz.
à The unit is connected to the power supply by an at-
tached power cable with a grounded contact plug.
à Extension cables may only be laid by authorised
electricians based on the capacity of a unit, the
length of the cable and in accordance with the in-
tended use.
G
The unit must be connected to the power supply at
a special terminal equipped with a switch to pro-
tect against faulty currents.
G
Extension cables may only be used once they are
unrolled.
G
Flexible fuel tubes must be protected from being
damaged, e.g. from forklifts, animals, etc.
Starting
Only those persons who have been trained in operation
of the unit may be responsible for operating and moni-
toring it.
Important information about starting the cold unit
The preheating of the nozzle stock delays the tempera-
ture depending start of the CLK 30 to CLK 70 units de-
livered with forced-air burners.
Connecting the unit to the power supply
1. Set the operating switch to “0” (OFF).
2. Connect the unit plug to a properly connected power
socket.
3. Open all shut-off fittings in the oil supply.
When operating the unit for the first time, air in the oil
supply can cause the burner to malfunction.
1. Plug the supplied bridge circuit plug
2 into the thermostat socket 1 of the
control panel.
2. Set the operating switch to I
heating.
Heating without a room thermostat
The unit runs in continuous operation.
1 2
Control Panel
bridge circuit plug
thermostat socket
reset button (burner)
control lamp, red (burner malfunction)
operating switch
control lamp, green (in operation)
safety temperature limiter
Note about the green control lamp (in operation).
The control lamp indicates that the unit is in
“heating”
mode.
When the unit is in
“ventilation” mode, nothing is dis-
played if the room thermostat is switched off or if the
STB was activated.
Ventilation
In this position only the supply air fan runs and the unit
can be used for air circulation.
1. Set operating switch to “II (ventilation).
2. Please note: in this mode, it is not possible to use
the thermostat nor can the unit be operated in
heating mode.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO CLK150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO CLK150 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO CLK150

REMKO CLK150 User Manual - German - 20 pages

REMKO CLK150 User Manual - Dutch - 16 pages

REMKO CLK150 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info