587877
11
Zoom out
Zoom in
Previous page
1/16
Next page
11
Cleaning internal components
For cleaning the interior of the unit
and to gain access to the electri-
cal components, it is necessary to
open the unit housing.
Clean the components either by
blowing out, suction, inlet grille
or with a soft brush. Do not use
a jet of water!
Carefully clean the internal
surfaces of the unit, condensate
trap with hose connection, fan
and fan housing.
Check all unit components for
possible damage and repair if
necessary.
Carefully refit all previously
removed components in the
reverse order.
NOTE
Only authorised specialists
may carry out adjustments and
maintenance.
Troubleshooting
The units were manufactured us-
ing the latest production methods
and tested repeatedly for perfect
function.
If faults should still occur, the unit
must be checked against the fol-
lowing list.
The unit does not start:
Check unit installation (tilt
switch)
The unit will only operate in an
upright position!
Check the supply connection
and system fuse
230V/1~/50
Hz
on-site
Check the mains plug and
power cord for damage
Check the condensate container
for level and correct seating
The “FULL TANK” indicator
light must not light up!
Check the microswitch of the
condensate container
Check for free air flow
Overheating
!
Check the miniature fuse on the
control pcb
The unit operates, but with
no condensate formation:
Check the room temperature
The operating range of the unit
is between 1°C and 40°C
Humidity has not reached
the fixed value (45% relative
humidity)
Check the air inlet and outlet
grilles for fouling
Clean or replace if necessary!
Have the exchanger surface of
the absorption rotor checked
for fouling.
This work makes it necessary
to open the unit and must
be carried out only by an
authorised specialist!
The unit is loud or
condensate discharges:
Check that the unit is standing
on a level and firm surface.
Check that the unit is standing
upright and stable.
Have the condensate trap or
connection checked for dirt
deposits.
This work makes it necessary
to open the unit and must
be carried out only by an
authorised specialist!
NOTE
Only authorised specialists
may carry out adjustments and
maintenance.
NOTE
Particular care must be taken
when cleaning the adsorption
rotor as the surface must not
be subjected to any mechani-
cal load.
ATTENTION
After carrying out all work on
the units, an electrical safety
test must be carried out in ac-
cordance with VDE 0701.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ASF100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ASF100 in the language / languages: English as an attachment in your email.

The manual is 0.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ASF100

REMKO ASF100 User Manual - German - 16 pages

REMKO ASF100 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info