510301
6
Zoom out
Zoom in
Previous page
1/111
Next page
ENGLISH
3
GBDNLFEIDKSFINPSKCZ
HUN
PL
RUTRROGRSLAE
HR/
SRB
GB
CARE FOR YOUR SHAVER
To ensure long lasting performance of your shaver, clean the head assembly regularly. The easiest and
the most hygienic way to clean the shaver is by rinsing the shaving head after use with warm water.
Always keep the protective cap on the shaving head when the shaver is not in use.
AFTER EACH USE
Ensure the lady shaver is turned off.
Press the side release button to slip open the head assembly.
Blow any loose debris from the foil.
Brush or rinse the accumulated hair from the main body of the shaver, head assembly and cutter
assembly.
Leave the head assembly open to let the shaver dry completely.
NOTE:
The lady shaver is suitable for use in the bath or shower.
Do not rinse with water hotter than 70°C.
Do not completely submerge the shaver in water.
Ensure that the lady shaver is turned off and unplugged from the mains when cleaning.
Do not clean the shaving foils with the brush.
At regular interval, put a drop of sewing machine oil onto the foils and cutters head.
REPLACING YOUR FOILS AND CUTTERS
To ensure the continued highest quality performance from your shaver, we recommend that the foil and
cutter are replaced every 6 months. These can be obtained from our nearest Remington
®
Service Centre.
Signs that your foils and cutters need replacing:
Irritation: As foils get worn, you may experience skin irritation.
Pulling: As the cutters wear, your lady shaver may not feel as close and you may feel your cutter
pulling your hair.
Wear through: You may notice that the cutters have worn through the foils.
TO REPLACE THE FOIL
Ensure the lady shaver is switched off.
Press the side release button to slip open the head assembly.
Gently push the small plastic tabs at either end of the foil carrier. The foils should then easily
detach from the head assembly.
To reassemble, snap the replacement foil carrier into position.
Close the head assembly.
CAUTION
Only hold the plastic to prevent damage to the foil.
Do not press on the foil when replacing.
TO REPLACE THE CUTTERS
Ensure the shaver is switched off and open the head assembly (as above).
To remove cutter, grasp cutter between thumb and forefi nger and pull upward.
To reassemble cutter, place cutter onto oscillator tip. Gently push down clicking into position.
100648_REM_IFU_WDF4830_21L.indd GB3100648_REM_IFU_WDF4830_21L.indd GB3 30.08.10 12:4330.08.10 12:43
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remington WDF4830C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remington WDF4830C in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info