714621
7
Zoom out
Zoom in
Previous page
1/152
Next page
7
, STEP 5 – The finishing touches
Use the clipper without a guide comb for close trimming around the base
and sides of the neck.
To produce a clean straight line at the sideburns, reverse the hair clipper.
Place the reversed clipper at right angles to the head, tips of the blades
lightly touching the skin and then work downwards.
, SHORT TAPERED STYLES – “FLAT TOPS” & SHORT CUTS
Starting with the longest guide comb attached (25mm), cut from the back of
the neck to the crown. Hold the guide comb flat against the head and slowly
move the clipper through the hair.
Use the same procedure from the lower side to the upper side of the head.
Then cut the hair against the direction in which it grows and level with the
sides.
To give a “flat top look, the hair on top of the head must be cut over the top
of a flat comb.
Use a closer guide comb to taper the hair down to the neckline as desired.
C CLEANING AND MAINTENANCE
To ensure long lasting performance of the clipper, clean the blades and
unit regularly.
Ensure the appliance is switched o and unplugged from the mains.
Do not use harsh or corrosive cleaners on the unit or blades.
Cleaning should be done with a soft brush.
After each use - Brush the accumulated hair from the blades.
Ensure the appliance is switched o and unplugged from the mains.
To clean the unit, wipe with a damp cloth and dry immediately.
, Note: Suitable for cleaning under water.
, WASHABLE CLEANING
The clipper is fully washable and can be easily cleaned under a running tap.
Press the blade release point to slide out the blade. Then the blade set can
easily be cleaned under the tap.
Once the blades are cleaned and dry, place the blade set on top of the
clipper and push it towards the hair clipper until it snaps into place.
We recommend that you oil the blades regularly. Add a few drops on all
gliding surfaces, the cutting area and back pads of the blades.
, Note: A hex wrench is provided to enable you to take the blade apart for
deep cleansing and also remove the taper lever if it needs to be replaced.
ENGLISH
GBDNLFEIDKSFINPSKCZ
HUN
PLRUTRROGRSI
AE HR
UA
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remington Ultimate Performance Hair Clipper HC9700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remington Ultimate Performance Hair Clipper HC9700 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info