490470
11
Zoom out
Zoom in
Previous page
1/162
Next page
ENGLISH
5
GBDNLFEIDKSFINPSKCZPL
HUN
RUTRROGRSLAE
HR/
SRB
GB
AUTO BOOST SYSTEM (Only for HC5750)
There are 3 settings for the Auto Boost system: Off, Auto and Boost.
If the clipper is set to Auto it will run at regular power under low load conditions.
When more power is needed, the clipper with automatically sense and provide maximum
Boost.
If the clipper is set to Boost, it will run at maximum power at all times.
DUAL BOOST SYSTEM (Only for HC5550)
There are 3 settings for the Dual Boost system: Off, On, Boost.
If the clipper is set to On, it will run at regular power.
If the clipper is set to Boost, it will provide maximum power.
CARE FOR YOUR HAIRCLIPPER
Your clipper is fitted with high quality blades. To ensure long lasting performance of your clipper,
clean the blades and unit regularly. Always keep the attachment guide comb on the trimmer
blade.
AFTER EACH USE
Ensure the clipper is switched off and disconnected from the mains.
Brush the accumulated hair from the blades. Do not submerge the clipper in water.
To clean the unit, wipe with a damp cloth and dry immediately.
Note: Ensure that the clipper is turned off when cleaning.
WASHABLE CLEANING
The QUICK WASH SYSTEM is designed to maximise the efciency of washable cleaning.
Click the buttons that are located on the sides of the hair clipper head. The blades will slide
out and the blade set can easily be cleaned under the tap.
Once the blades are cleaned the blades are locked into place by pushing the blade set
towards the hair clipper head and will snap into place.
Do not run the entire unit under the tap, only the blade set is meant to be submerged in
water.
Note: Ensure that the hair clipper is turned off when cleaning.
EVERY SIX MONTHS
At regular intervals the Blade Set should be removed and cleaned.
Remove the 2 screws retaining the fixed blade with a screwdriver. Do not remove blade set.
Brush out hairs from between the blades with soft cleaning brush. Do not remove the
lubricating grease from the blades. It is not necessary to remove the small moving blade
from the unit.
If the moving blade has been removed this can be re-fitted by slotting the ceramic coated
blade holder over the pin in the centre of the interior product head. The groove on the
ceramic coated blade, just below the teeth, rests on a metal plate at the opposite side to
100158_REM_IFU_HC5350_21L.indd 5100158_REM_IFU_HC5350_21L.indd 5 26.03.10 11:3226.03.10 11:32
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remington HC5350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remington HC5350 in the language / languages: German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Remington HC5350

Remington HC5350 User Manual - English - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info