Manual Remington HC4255 (page 6 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish, All languages)

719577

Zoom out

Zoom in

1/120

CARE FOR YOUR HAIRCLIPPER

• To ensure long lasting performance of your clipper, clean the blades and unit regularly.

• Always keep the clipper in the provided travel pouch.

• Ensure the appliance is switched o and unplugged from the mains before cleaning.

• Do not use harsh or corrosive cleaners on the unit or blades.

• Cleaning should be done with a soft brush.

• After each use - brush the accumulated hair from the blades.

WASHABLE CLEANING

• The QuickCut Clipper is fully washable for easy cleaning.

• Ensure the appliance is switched o and unplugged from the mains.

WASHOUT PORT INSTRUCTIONS

Note: Never rinse, wash or otherwise subject this product to liquid whilst the power cord is connected.

• For best results, keep trimmer running while running it under the tap. Allow water to run through the

washout port and over the blades. Recommended to rinse after each use.

• Ensure the clipper is dry after cleaning.

• For more thorough cleaning the blade set can be easily removed to wash any hair trimmings from the

blades. To release the blade set, push the blade set release button found on the base of the clipper.

• Ensure the blades are dry after rinsing under the tap. To reattach, align the blade set onto the clipper

and push the blade set towards the clipper body until it clicks into place.

• Place a small drop of cutter or sewing machine oil onto the blades at each end and at the middle point of

the blades. Turn the unit on for a few seconds to distribute the oil then turn o and wipe o excess oil.

BATTERY REMOVAL

• The battery must be removed from the appliance before it is scrapped.

• The appliance must be disconnected from the supply mains when removing the battery.

• Ensure the clipper is discharged of all power.

• Starting at the seam on either side of the charge indicator lens, pry open seam working back and forth

from one side to the other, following the seam until the top shell has been pried apart all the way from

the rest of the clipper. Remove the two screws from the inner housing.

• Gently pull the inner housing straight up and away to remove the inner housing shell.

• Remove the two screws from the inner structure located on each side of the circuit board.

• Gently pull the inner structure containing the battery and circuit board up out of the lower housing

structure of the clipper.

• From the under side of this inner structure, cut the red and black wires which lead to the battery.

• With the inner housing structure right side up, pull upward rmly on the circuit board to allow room

to remove the battery. Pry the battery out of its holder.

• Dispose of the batteries safely.

RECYCLING

To avoid environmental and health problems due to hazardous substances,

appliances and rechargeable and non-rechargeable batteries marked with one of

these symbols must not be disposed of with unsorted municipal waste. Always

dispose of electrical and electronic products and, where applicable, rechargeable

and non-rechargeable batteries, at an appropriate ocial recycling/collection point.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Remington HC4255 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish, All languages as an attachment in your email.

The manual is 1,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Remington HC4255 Manual

Product: