510218
7
Zoom out
Zoom in
Previous page
1/134
Next page
5
GBDNLFEIDKSFINPSKCZ
HUN
PL
RUTRROGRSLAE
HR/
SRB
GB
Brush out hairs from between the blades with soft cleaning brush. Do not remove the
lubricating grease from the blades. It is not necessary to remove the small moving blade
from the unit.
If the moving blade has been removed this can be re-tted by slotting the ceramic blade
holder over the pin in the centre of the interior product head. The groove on the ceramic
blade, just below the teeth, rests on a metal plate at the opposite side to the screw holes.
The fixed blade is fitted with the raised prole pointing outwards and fixed with the 2
screws.
Before fully tightening the 2 screws, adjust the taper lever to the lower position and align
the blades so that their cutting edges are parallel to one another. Tighten the 2 screws.
Note that if the blades are not correctly aligned then cutting efciency will be impaired.
Place a few drops of cutter or sewing machine oil onto the blades. Wipe off excess oil.
CAUTION: Do not use liquid cleaners on the blades or harsh or corrosive chemicals on
the blade casing. Always use a soft brush to remove the accumulated hairs.
Unplug the charge adaptor from the power outlet when fitting or removing attachments,
or while cleaning the product.
Always store this appliance and cord in a moisture-free area.
Do not wrap the cord of the charging adaptor around the appliance.
TROUBLESHOOTING
If blades do not seem to cut hair easily, the taper lever (PICTURE 6) can be used to remove
any hair caught between the comb and blade. Switch the clipper on and move the taper lever
up and down a few times but do not force the lever in either direction. This should remove
hairs and restore the cutting efciency. If not, contact your nearest Remington
®
Service
Centre.
IMPORTANT SAFETY INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR
INJURY TO PERSONS:
An appliance should never be left unattended when plugged into a power outlet.
Keep the power plug and cord away from heated surfaces.
Make sure the power plug and cord do not get wet.
Do not plug or unplug the shaver with wet hands.
Do not use the product with a damaged cord. A replacement can be obtained via our
International Service Centres.
Charge, use and store the product at a temperature between 15°C and 35°C.
Always unplug from the mains when cleaning.
Only use the parts supplied with the appliance.
ENGLISH
080705_REM_IFU_HC363C_22L.indd 5080705_REM_IFU_HC363C_22L.indd 5 03.11.2008 19:06:40 Uhr03.11.2008 19:06:40 Uhr
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remington HC363C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remington HC363C in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 3,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info