805732
53
Zoom out
Zoom in
Previous page
1/104
Next page
1. Den Haltebügel des Siphons nach hinten ziehen.
2. Den Siphon vorsichtig nach unten ziehen.
3. Den Siphon bis zur Markierung mit Wasser füllen.
4. Den Siphon fest in die entsprechende Öffnung unter dem
Heizkessel drücken.
5. Den Haltebügel des Siphons nach vorne drücken.
6. Überprüfen, ob der Siphon fest im Heizkessel sitzt.
Gefahr!
Der Siphon muss immer ausreichend mit Wasser gefüllt sein.
Dadurch wird verhindert, dass Abgase in den Raum eindringen.
6.1.3 Gaskreis
Warnung!
Sicherstellen, dass der Heizkessel von der Stromversorgung
getrennt ist.
1. Den Hauptgasabsperrhahn öffnen.
2. Den Gasabsperrhahn unter dem Heizkessel öffnen.
3. Den Gasanschlussdruck an der Prüföffnung an der Gasleitung
messen.
Warnung!
Zugelassene Gasdrücke siehe: Gerätekategorien, Seite 96
4. Die Gasversorgungsleitung entlüften, indem die Prüföffnung
losgeschraubt wird.
5. Die Prüföffnung wieder festschrauben, wenn die Leitung vollständig
entlüftet wurde.
6. Alle Anschlüsse auf Gasdichtheit prüfen. Der Prüfdruck darf
höchstens 60 mbar betragen.
6.2 Beschreibung des Schaltfelds
6.2.1 Schaltfeld-Elemente
1 Drehknopf zur Auswahl von Symbolen, Menüs oder Einstellungen
2 Bestätigungstaste zur Bestätigung der Auswahl
3 Zurück-Taste :
Kurzes Drücken: Zurück zum vorherigen Bildschirm oder zum
vorherigen Menü
Langes Drücken: Zurück zum Startbildschirm
4 Menü-Taste zum Aufrufen des Hauptmenüs
5 Display
6 Status-LED
6.2.2 Beschreibung des Hauptanzeige
Dieser Bildschirm wird nach dem Einschalten des Gerätes automatisch
angezeigt. Das Schaltfeld geht automatisch in den Standby-Betrieb
(schwarzer Bildschirm), wenn die Tasten 5 Minuten lang nicht betätigt
werden. Eine der Tasten am Schaltfeld betätigen, um den Bildschirm
wieder zu aktivieren.
Abb.69 Befüllen des Siphons
AD-0000231-03
6
32
45
1
Abb.70 Prüföffnung für Gas
AD-0000121-01
Abb.71 Schaltfeld-Elemente
AD-3000932-02
4
6
3
2
1
5
6 Vorbereitung zur Inbetriebnahme
7698981 - v.04 - 30092021 53
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Quinta Ace 160 HMI T-control SCB-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Quinta Ace 160 HMI T-control SCB-10 in the language / languages: German as an attachment in your email.

The manual is 3.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info