805732
48
Zoom out
Zoom in
Previous page
1/104
Next page
Brenner nicht und der Kessel wird gesperrt. Die Wartezeit wird über den
Parameter AP008 eingestellt. Bei einer Wartezeit von 0 wird der Kontakt
deaktiviert.
5.6.5 Die Erweiterungsleiterplatte SCB-01
Die SCB-01 hat folgende Merkmale:
Zwei potentialfreie Kontakte für Statusbenachrichtigungen
0–10 V Ausgangsanschluss für eine PWM-Systempumpe
Erweiterungsleiterplatten werden automatisch von der Regelungseinheit
des Kessels erkannt. Wenn Erweiterungsleiterplatten entfernt werden,
zeigt der Kessel einen Fehlercode an. Um diesen Fehler aufzuheben,
nach dem Entfernen die automatische Erkennungsfunktion ausführen.
Anschluss an Kontakt Status
Die beiden potentialfreien Kontakte Status lassen sich nach Bedarf
konfigurieren. Abhängig von der Einstellung kann ein spezifischer Status
vom Heizkessel übertragen werden.
Ein Relais wie folgt anschließen:
Nc Öffner. Der Kontakt öffnet sich, eine Statusänderung erfolgt.
CHauptkontakt.
No Schließer. Der Kontakt schließt sich, eine Statusänderung erfolgt.
Wählen Sie die gewünschte Statusmeldung (Einstellung) mit den
Parametern EP018 und EP019.
Anschließen eines Ausgangs 0-10 V
An Kontakt 0 -10 kann eine modulierende PWM-Systempumpe
angeschlossen werden. Die Pumpenleistung wird durch das vom
Heizkessel kommende Signal moduliert. Je nach Marke und Typ kann die
Pumpe mit einem 0–10-V-Signal oder einem PWM-Signal angesteuert
werden.
Die Steuereinheit der Systempumpe an Steckverbinder 0-10 anschließen.
Die Auswahl des vom Heizkessel gesendeten Signaltyps erfolgt über
den Parameter EP029.
Die Auswahl des Signaltyps zur Ansteuerung der Pumpe erfolgt über
den Parameter EP028.
Vorsicht!
Verwenden Sie, wenn möglich, das Modulationssignal von der
Pumpe. Dieses liefert eine größere Genauigkeit auf der Ebene
der Pumpensteuerung.
Wenn der Feuerungsautomat nicht die Pumpenmodulation
übernimmt, verhält sich die Pumpe wie eine Ein/Aus-Pumpe.
5.6.6 Die Erweiterungsleiterplatte SCB-10
Die SCB-10 hat folgende Merkmale:
Regelung von 2 (Mischer-)kreisen
Regelung eines dritten (Mischer-)kreises über eine optionale
Regelungsleiterplatte
Regelung eines Trinkwasserkreises (TWW)
Abb.54 Regelungsleiterplatte SCB-01
AD-3001514-01
NoCNc
Status
NoCNc
Status
+0
0-10
Abb.55 Statusmeldungen
AD-3001312-01
C No
Nc
Status A
C No
Nc
Status B
Abb.56 0–10 V Ausgangsklemme
AD-3001305-01
+
-
0-10
5 Installation
48 7698981 - v.04 - 30092021
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Quinta Ace 160 HMI T-control SCB-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Quinta Ace 160 HMI T-control SCB-10 in the language / languages: German as an attachment in your email.

The manual is 3.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info