805710
43
Zoom out
Zoom in
Previous page
1/78
Next page
Bedienungs- und Wartungsanleitungen – GAHP-A
43
Hat das Kabel keinen ausreichenden Durchmesser, um in der Kabelhalterung blo-3.
ckiert zu werden (Detail C in Abbildung5.11 Kabelanschluss CAN-Bus 42), den
Durchmesser mit einigen Wicklungen Isolierband vergrößern. Das Isolierband
muss in der Nähe des abisolierten Teils angebracht werden (annähernder Durch-
messer: 12-13 mm).
Die Abschirmung über den Kabelmantel stülpen; Das Isolierband am Ende des um-4.
gestülpten Teils der Abschirmung anbringen (Detail A der Abbildung 5.11 Kabel-
anschluss CAN-Bus 42).
Ist das Gerät ein 5. Endknoten im Netz, die drei farbigen Adern an den orangefarbe-
nen Verbinder anschließen, siehe Detail "A" in Abb. 5.12 Schaltplan 43. Die rich-
tigen Angaben L, H, GND der Tabelle 5.2 CAN Bus-Kabeltypen 42, der Abbildung
und auf der Schaltplatine am Fuß des Verbinders beachten.
Ist das Gerät ein 6. Zwischenknoten , die Schritte von Punkt 2 bis Punkt 5 auch für
den anderen Kabelabschnitt wiederholen (bei dieser Vorgehensweise sind zwei
Kabelenden ohne Kabelmantel vorhanden). Die gleichfarbigen Adern verflech-
ten und am orangefarbenen Verbinder anschließen, siehe Detail "B" in Abb. 5.12
Schaltplan 43.
Das CAN-BUS-Kabel (oder die zwei Kabel, je nach Art des Knotens, der angeschlos-7.
sen werden soll) in der Kabelhalterung oben in der Schalttafel befestigen, sodass
die Abschirmung einen guten Kontakt mit dem Metallbügel hat. Zur Überprüfung
leicht am Kabel ziehen. Die Kabel müssen richtig in der Kabelhalterung blockiert
sein.
Zur Positionierung der Jumper an der Schaltplatine je nach zu konfigurierendem
Knoten:
Ist das Gerät ein • Zwischenknoten im Netz (im orangenen Kabelstecker, der in die
Schaltplatine eingesetzt wurde, befinden sich 3 Leiter): die Jumper wie im Detail A
der Abbildung 5.12 Schaltplan 43 dargestellt positionieren.
Ist das Gerät ein • Zwischenknoten im Netz (im orangenen Kabelstecker, der in die
Schaltplatine eingesetzt wurde, befinden sich 6 Leiter): die Jumper wie im Detail
"B" des Beispiels 5.12 Schaltplan 43 dargestellt positionieren.
Abbildung 5.12 – Schaltplan
Anschluss des CAN-Bus-Kabels an die Steuerplatine: Detail A Fall "Endknoten", Detail B Fall "Zwischenknoten"
ZEICHENERKLÄRUNG
SCH Steuerplatine
GND Gemeinsamer Datenleiter
L TIEFES DATENSIGNAL
H HOHES DATENSIGNAL
J1 CAN-Bus Jumper auf Platine
A Detail Fall "Endknoten" (3-adrig;
J1=Jumper "geschlossen")
B Detail Fall "Zwischenknoten" (6-adrig;
J1=Jumper "offen")
P8 CAN Port / Stecker
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha GAHP-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha GAHP-A in the language / languages: German as an attachment in your email.

The manual is 8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info