689813
71
Zoom out
Zoom in
Previous page
1/124
Next page
Om de verbranding te controleren:
1. Schroef de dop in het rookgasmeetpunt los.
2. Sluit de rookgasanalyser zodanig aan, dat de opening rond de sensor
tijdens de meting goed is afgedicht.
3. Kies het schoorsteenveger pictogram.
Het menu Verander de belastingtest stand wordt weergegeven.
4. Kies het vermogen voor de schoorsteenveegtest:
Minimaal vermogen: minimum ketelvermogen
Maximaal vermogen CV: maximum ketelvermogen in
verwarmingsmodus
Maximaal vermogen SWW: maximum ketelvermogen in sanitair-
warmwatermodus
De verbrandingstest start. De melding Belastingtest
geaccepteerdwordt weergegeven.
5. Meet de concentratie O
2
in de rookgas met de analyser.
6. Indien de O
2
waarde niet overeenkomt met de gewenste waarde, pas
dan de rotatiesnelheid van de ventilator aan V.
7. Selecteer Stat. schoorsteenmod.
8. Kies een andere uitgang.
9. Draai de dop terug op het rookgasmeetpunt zodra de metingen zijn
voltooid.
Voor meer informatie, zie
Branderinstelwaarden, pagina 69
8.4
Na de inbedrijfstelling te controleren punten
1. Verwijder de meetapparatuur.
2. Draai de dop op het rookgasmeetpunt.
3. Plaats de frontmantel terug.
4. Voer de CV-installatietemperatuur op tot ongeveer 50°C.
5. Schakel de ketel uit.
6. Ontlucht de cv-installatie na circa 10 minuten.
7. Controleer op lekdichtheid (hydraulisch circuit, oliecircuit, enz.)
8. Controleer of de keteluitrusting correct werkt.
9. Controleer of de thermostaten correct werken en correct zijn
ingesteld.
10. Controleer de waterdruk. Aanbevolen druk: tussen 0,15 en 0,2 MPa
(1,5 en 2,0 bar).
11. Berg het verpakkingsmateriaal op of gooi het weg.
12. Instrueer de gebruiker over de werking van de installatie, ketel en
regelaar.
13. Informeer de gebruiker over het noodzakelijke periodieke onderhoud.
14. Overhandig alle handleidingen aan de gebruiker.
De ketel is nu bedrijfsklaar.
Afb.70
MW-2000483-2
1
2
Off
Afb.71
MW-1001076-3
Configuration brûleur modulant
System flow temp 28.5 °C
Ftat 28.5 °C
100.00 %
Actual rel.Power
CU-OH-02
Load Test
14 : 23
Press and hold
button to changeload test mode
i
Off
Perform load tests on pabable devices
Home screen
Configure Modulating Burner
Change load test mode
Off
8 Inbedrijfstelling
7665664 - v03 - 14052018 71
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Calora Tower Oil PRO 60 LS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Calora Tower Oil PRO 60 LS in the language / languages: Dutch as an attachment in your email.

The manual is 15,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Remeha Calora Tower Oil PRO 60 LS

Remeha Calora Tower Oil PRO 60 LS Usermanual and installation guide - French - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info