490492
29
Zoom out
Zoom in
Previous page
1/53
Next page
ENGLISH
29
5.1 MIDI ASSIGNMENT
NOTE!
By default Mixage is congured for MIDI channels 1 or 2. The MIDI channell can be selected via
the switch on the rear side -B43-.
It is possible to connect a further Mixage controller, i.e. for DJ teams. For this purpose it is important
that one Mixage is on MIDI channel 1 and the second Mixage is on MIDI channel 2 (see switch -B43-).
Reloop‘s ofcial mappings are laid-out according to the standard conguration. Therefore changes
are usually unnecessary.
NOTE!
Updated and advanced mappings can also be found online. Go to http://www.reloopdj.com/forum
and open the category „Mapping Files“ under „Downloads for all Reloop products“.
5.2 LED FUNCTIONAL TEST
Herewith it is possible to check whether all of Mixage‘s LEDs work properly.
To carry out the functional test proceed as follows:
1. Make sure that Mixage is turned off (see position On/Off Button -B41-).
2. Press and hold the left Sync Button -T16- and turn on Mixage via the On/Off Button -B41-.
3. Now release the Sync Button -T16-.
4. Now all LEDs should be illuminated.
5. In order to nish the test, simply turn off the device via the On/Off Button -B41-.
6. UPDATES & SUPPORT
For Reloop Mixage it is possible to update its rmware. This way changes can be applied and new
features added subsequently. Instructions on how to proceed can be found online under the below
mentioned address.
Especially updated drivers for the integrated audio interface are offered which can be downloaded.
6.1 FIRMWARE CHECK
1. Turn off the device via the On/Off Button -B41-.
2. Press and hold the right Shift Button -T3-.
3. Turn on the device via the On/Off Button -B41-.
4. The rmware version is displayed via the Level LED Display -T32-.
Example: Left LED Display: 1 LED + right LED Display: 5 LEDs = Firmware version 1.5
6.2 FIRMWARE UPDATE
1. Make sure that Mixage is turned off (see position On/Off Button -B41-) and connected to the com-
puter via USB.
2. Press and hold the TRAX Encoder -T20- and turn on Mixage via the On/Off Button -B41-.
3. Now release the button -T20-.
4. The Power Status LED -T30- and the MIDI Status LED -T31- will now ash. Mixage is now in update mode.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reloop MIXAGE Controller Edition at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reloop MIXAGE Controller Edition in the language / languages: English, German, French as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info