417382

Rel stentor Manual

4
Zoom out
Zoom in
Previous page
1/11
Next page
4
To Connect to the Power Amplifier:
1. Your existing speaker wires can be twisted together with the signal
interconnect to STENTOR and connected to the gold plated 4mm plugs
supplied. Alternatively, use your existing plugs or connect the STENTOR
lead to a spare set of speaker terminals. In effect the STENTOR is bi-wired
from your power amplifier. However, note that there are only three
connections to STENTOR. This is deliberate and helps preserve the existing
star earthing of your system (assuming it has a star earth arrangement).
Remove the speaker leads to the RIGHT or the LEFT channel of your power
amplifier (whichever is the most convenient). Connect either one of the
RED banded plugs on the interconnect to the RED terminal of whichever
channel you have selected on your power amplifier. Connect the BLACK
banded plug from STENTOR to the BLACK terminal of this channel. Now do
the same with the other channel by connecting the other RED banded plug to
this channel’s RED terminal. Connect the XLR plug to the high level input on
STENTOR.
3. Connect the Mains lead to STENTOR and to the mains and switch ON.
Operate the Earth Lift switch, if there is no hum, leave in the OUT position.
This ensures that there is only one earth return on your system, preserving
the star earthing arrangements in your power amp. If the XLR plug is
removed there will be a hum. The hum can be removed by operating the
earth lift switch if desired. Sometimes this hum will reappear if the main
power amp is switched off. If this occurs, leave the earth lift switch IN.
To Connect to a Dedicated Sub-woofer Output:
1. For this connection it will be necessary to use whatever type of connector is
needed by this output. Normally it would be a phono type connector.
Whatever the type, the yellow wire of the STENTOR interconnect should be
connected to the signal live of this connector and the red and black to signal
ground. The red wire is connected to ground to minimise hum pickup. The
600 Ohm balanced line input is then used in place of the high level XLR
input. With very long interconnects and some amplifiers, particularly ones
with a higher output impedance, there may be a slight hum. If so, screened
interconnect will have to be used.
2. Plug the connector into the dedicated sub-woofer output on your power
amplifier and the XLR plug into the 600 Ohm balanced Line level input on
STENTOR.
3. Follow Step 3 above to connect to the mains.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rel stentor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rel stentor in the language / languages: English as an attachment in your email.

The manual is 0,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info