413316
11
Zoom out
Zoom in
Previous page
1/27
Next page
REL Acoustics ‘ST III’ User Manual
11
CONTROLS AND CONNECTIONS (Cont)
MODE SWITCH. Used to set phase* and to bypass crossover for Low Level input**.
Position 1 / Line: 0 degrees phase, crossover engaged low level input
Position 2 / LFE: 0 degrees phase, crossover bypassed for low level input
Position 3 / Line: 180 degrees phase, crossover engaged for low level input
Position 4 / LFE: 180 degrees phase, crossover bypassed for low level input
*Phase selection affects both Hi and Lo level inputs
**Crossover is always engaged for Hi level input regardless of mode switch
position.
LO LEVEL input volume control. Adjust for output level when using LO LEVEL phono
input
or balanced line level input XLR socket.
HI LEVEL input volume control. Adjust for output level when using HI INPUT Neutrik
socket or BAL HI INPUT Neutrik socket.
FINE ROLL OFF control. Fine adjustment of roll off point, used in conjunction with
Coarse Roll Off control (below). See chart on amplifier panel or in this manual, page 8,
for crossover frequencies determined by setting combinations of both controls.
COARSE ROLL OFF control. Coarse adjustment of roll off point, used in conjunction
with Fine Roll Off control (above). See chart on amplifier or in this manual, page 8, for
crossover frequencies determined by setting combinations of both controls.
0dB LO INPUT phono socket. Used to connect the Sub Bass System at low level to
the sub/LFE output of the amplifier/processor or left and right pre-amp outputs.
If Lo Level inputs are used to connect pre-amp right and left outputs then a 12dB
attenuator is available from REL to balance the two inputs.
Alternatively, a high quality Y-adaptor may be employed to connect at either input as
system gain characteristics demand.
+12dB LO INPUT phono socket . As 6 but a higher sensitivety. If LO LEVEL inputs
are used connected to pre-amp right and left outputs then a 12 dB attenuator is
available from REL to balance the two inputs.
Alternatively, a high quality Y-adaptor may be employed to connect at either input as
system gain characteristics demand.
BAL HI INPUT Neutrik Speakon socket. Used to connect the Sub Bass System at high
level to the speaker output of one channel of a differential output or bridged to mono
amplifier.
Note:- 230 volt models of Stentor III and Studio III have two BAL HI INPUTS.
UNBAL HI INPUT Neutrik Speakon socket. Used to connect the Sub Bass System at
high level to the main speaker output of amplifiers.
BAL LO INPUT XLR socket. Used to connect the Sub Bass System at low level to pre-
amplifier balanced line outputs. (Not on Strata III)
Note:- 230 volt models of Stentor III and Studio III have two balanced line inputs.
1
2
3
4
6
7
8
9
10
0
5
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rel stentor iii at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rel stentor iii in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info