592112

Reflexion CLR-2970KCD Manual

4
Zoom out
Zoom in
Previous page
1/19
Next page
EnglishEnglish
3 4
sound when reach the alarm 2 time.
- or when alarm 1 sound then PRESS POWER/ALARM RESET button directly, it will
switch to alarm 2 fuction.
- by keeping the NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16)
pressed, the time runs forwards or backwards at high speed.
Normal condition
Press POWER/ALARM RESET button (1) to turn on the LCD back light and
switch to normal condition.
RADIO OPERATION
In normal condition, press TUNER button (11) to enter radio function.
- press VOL+ (17)/VOL- (18) to turn UP/ DOWN the volume, “l up/ l dn” will be
shown on
the LCD.
- repeat press STOP/BAND button (14) to select the station of FM/AM.
- press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16) to receive
the frequcecy of the station.
Press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16) once, the
change of FM frequcncy is 100Khz, and the change of am frequency is 9Khz.
PressNEXT/FF/TUN+ button (12) orPREVIOUS/FB/TUN- button (16) for 2 seconds,
it will switch to automatically search the station function.
Antenna
For FM reception there is a wire FM antenna at the rear of the unit. Extend the antenna and
move it around to obtain the best reception.
For MW reception the signals are picked up through a wire antenna. Your may have to orient
the wire to obtain the best reception.
PROGRAM RADIO OPERATION
- In radio condition, press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN-
button (16) to select the station which to be programed.
- press PROG/C-ADJ button (15) to enter program function. LCD will display
“MEMORY” and “P”.
- press REPEAT/M-RECALL (9) button to select the required station number, then
press PROG/C-ADJ (15) button to confirm the station number.
- repeat the above operations can program 30 stations. there are 15 programs in
the FM/AM separately.
- when turn on the radio, press REPEAT/M-RECALL button (9) you can repeat
index the station which stored in the program.
MOUNTING
1. Choose a spot near an electrical outlet.
2. Rotate the 4 mounting adapters to choose the apposite distance between the unit
and the spot.
3. Mark the mounting position, drill 4 holes x diam. 6 mm.
4. Install the mounting adapter on the spot.
Note : Fixings used to mount this unit must be suitable for construction material.
POWERSUPPLY
This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power cord to the AC
household main outlet. Ensure that the voltage is as indicated on the rating plate on the rear
of the unit.
- mains plug is used as the disconnect device, the disconnect device shall
remain readily operable. always remember to disconnect the power cord from
the main supply before disconnecting the lead from the unit.
- when connect to the main power, the initial state of the unit will display “0:00”.
- reset both the correct time and the required alarm time for proper operation.
SETTINGTHECORRECTTIME
Time setting on the unit should be done in POWER OFF mode only.
Clock setting:
- press and hold the prog/c-adj button (15).
- at the same time press NEXT/FF/TUN+ (12) button or PREVIOUS/FB/TUN- button
(16) separately to set the hour or min time.
Alarm setting:
- slide the function switch (AUTO-CD-TUNER-BUZZER) (19) to BUZZER position.
- press disp button (4) to choose al1 or al2 setting, LCD will display al1 or al2.
- the first time press disp (4) is al1 function, then set the alarm time, the operation
is same as clock setting. after setting the alarm time press ALARM/ON/OFF button
(5) to store the time.
- then set the alarm 2. the alarm2 setting is same as alarm 1. When the time is the
same as the alarm 1 time, the buzz trump sounds. press the snooze button (8) to
turn off the alarm 1 sound temporarily. This time will cancel the alarm 2 function if
not press POWER/ ALARM RESET button (1). After 9 minutes the alarm 1 sound
again.
- If alarm 1 sounds press the snooze button (8) then continue press the POWER/
ALARM set button (1) alarm 1 will not sounds after 9 minutes. But the alarm 2 will
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reflexion CLR-2970KCD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reflexion CLR-2970KCD in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info