Manual Reer 1928 (page 12 of 54) (English, German, Dutch, Danish, French, Italian, Polish, Spanish)

716135

Zoom out

Zoom in

1/54

- 12 -

Assembly

Assembly of changing table heater with pedestal

Wall-mounted assembly of changing table heater

Safety instructions for wall installation:

• The changing table heater must be mounted on the wall in a stationary and level position. It must not be mounted on

the ceiling!

• The changing table heater must not be mounted on wood, plastic or other flammable materials or under plug sockets.

• IMPORTANT! Minimum distances: The minimum distance between the heater and the changing table is 100 cm. A mi-

nimum distance of 35 cm between the heater and the ceiling must be observed at all times. The heater must be placed

at least 65 cm away from furniture and flammable materials. Fire hazard in case of non-compliance!

• For installation in bathrooms or shower rooms, the regulations of the local utility company must be observed. The heater must

be positioned in such a manner that the pull switch cannot be reached from the bath or shower.

• Never install the unit above a bath tub!

Please fold out the inside cover of your user manual for a graphic illustration of the assembly process.

1. Insert the 5 feet (B) into the foot connector system (A) as shown in fig. A1.

2. Place the foot cover (C) on top (fig. A2).

3. Insert the lower attachment tube (D) into the opening (fig. A3).

4. Fix the lower attachment tube in position by inserting the plastic screw (E) from below (fig. A4).

5. Slide a cable holder (G) over the lower attachment tube (fig. A5).

6. Connect the middle attachment tube (H) with the groove to the lower attachment tube as shown in fig. A6 and turn the middle

attachment tube until the holes in both tubes align.

7. Fix the middle attachment tube into place using the supplied screw (H) and a Philips screwdriver.

8. Slide the remaining cable holder (G) over the middle tube and connect the upper attachment tube (I) to the middle attachment

tube (fig. A7). Fix the upper attachment tube in position using the supplied screw and a Philips screwdriver.

9. Remove the assembly plate from the unit as shown in fig. A8.

10. Place the changing table heater (J) on the pedestal and fix it in position with the plastic screw (F) (fig. A9).

11. Open the grey locking screw of the upper attachment tube (fig. A10) and set the changing table heater to the desired height

using the telescopic rod. Ensure that a minimum distance of 100 cm to the changing table is observed. Adjust the unit to the

desired height by closing the locking screw.

12. Secure the cable by pushing it into the cable holders (fig. A11).

13. Position the changing table heater in the desired location, out of reach of children and observing the specified minimum distan-

ces. Ensure that the pedestal is positioned securely on a level surface.

Note: For an installation with fewer than 5 feet (for example due to limited space), the user must ensure stability of the changing

table heater pedestal by other means. Never place a changing table heater with fewer than 5 feet freely in a room.

1. Remove the assembly plate from the unit as shown in fig. B1.

2. Hold the wall bracket on the wall taking into account the minimum distances (fig. B2) and mark the drill holes with a pencil. Use

a spirit level to ensure the bracket is level.

3. Bolt the wall bracket to the wall (fig. B3) using the supplied screws and wall plugs (J).

4. Slide the changing table heater into the relevant grooves on the wall bracket (fig. B3).

5. Screw the changing table heater to the wall bracket (fig. B4) using the screws removed in fig. B1.

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Reer 1928 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Reer 1928 Manual

Product: