Manual Reer 19050 EasyHeat Flex (page 8 of 33) (English, German, Dutch, Danish, French, Italian, Polish, Spanish)

716210

Zoom out

Zoom in

1/33

1514

Putting into operation

1. Insert the mains plug into the power socket (ﬁg. 1)

2. Pull the pull cord (ﬁg. 2) to switch the heater on. The heater has heat settings: 500 W.

3. Automatic shut-oﬀ is directly activated. After 10 minutes, the device is automatically switched oﬀ or it may be

switched oﬀ at an earlier point by pulling the cord again.

Switch-oﬀ if tilted

The unit has an automatic switch-oﬀ function if tilted. If the angle exceeds 25° (for example if the unit is mounted

on the ceiling), the power supply to the unit is cut. The unit switches back on automatically, when it is upright again.

Troubleshooting

issue possible causes remedial action

No heat radiation despite heat

setting

• The power plug is not connected

properly.

•

The automatic switch-oﬀ function

(timer) is activated.

•

The automatic tilt switch-oﬀ

function is activated, because the

angle of the heater exceeds 25°.

• Check the power plug.

• Turn the „Timer“ to „Oﬀ“ or switch

the unit oﬀ and then on again by

repeatedly pulling the pull cord.

• Ensure that the heater is level and

ﬁxed to the wall or the pedestal

is upright.

Heat radiation despite the

indicator being switched oﬀ.

Defective LED Please contact the customer service

100 cm

35 cm

20 cm

Warranty

Please retain your receipt, the user manual and part number.

Claims under warranty or under warranty commitments are to be processed by the dealer alone.

The technical speciﬁcation, information and characteristics of the product described herein have been compiled

to the best of our knowledge and belief and are correct at the time of printing. Any information provided by

reer should be correct and authoritative. Nevertheless, reer does not accept liability for potential errors in this

document and reserves the right to make changes to the product design and/or speciﬁcations without prior notice.

Reproduction and disclosure of information contained in this copyright-protected document, in any form or by

any means - graphical, electronic or mechanical by photocopying, recording on tape or storage in a data retrieval

system - even in part, require prior written consent from reer.

Environmental protection

At the end of its life, this product must not be disposed of as normal domestic waste, but should

be recycled at a collection point for electrical appliances. Please see the relevant symbol on the

product, in the user manual and packaging. Materials can be recycled as speciﬁed. An important

contribution to the protection of the environment can be made by reusing the unit, recycling its

components or otherwise reusing old appliances. Please contact your local council to ﬁnd out more

about an appropriate disposal centre.

11. Open the grey locking screw of the upper attachment tube and set the changing table heater to the desired

height using the telescopic rod. Ensure that a minimum distance of 100 cm to the changing table is observed.

Adjust the unit to the desired height by closing the locking screw.

12. Secure the cable by pushing it into the cable holders.

Note: For an installation with fewer than 5 feet (for example due to limited space), the user must ensure stability

of the changing table heater pedestal by other means. Never place a changing table heater with fewer than 5 feet

freely in a room.

Position the changing table heater in the

desired location, out of reach of children

and observing the speciﬁed minimum

distances. Ensure that the pedestal is

positioned securely on a level surface.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Reer 19050 EasyHeat Flex in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 13,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Reer 19050 EasyHeat Flex Manual

Product: