559687
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
Inspect and tighten all parts of the exercise bike regu-
larly. Replace any worn parts immediately.
To clean the exercise bike, use a damp cloth and a
s
mall amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
CONSOLE TROUBLESHOOTING
If the console display becomes dim, replace all the
batteries at the same time; most console problems are
the result of low batteries. See assembly step 5 on
page 8 for replacement instructions. If the handgrip
pulse sensor does not function properly, see step 5 on
page 15.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must first remove the left pedal and the
left front shield. Using an adjustable wrench, turn the
left pedal clockwise and remove it. Next, remove all
the screws from the left and right front shields; there
are two sizes of screws in the front shields–note
which size of screw you remove from each hole.
Then, gently pull the left front shield away from the
frame.
Locate the Reed Switch (46). Turn the Pulley (29) until
a Magnet (30) is aligned with the Reed Switch. Next,
loosen, but do not remove, the indicated M4 x 16mm
Screw (57). Slide the Reed Switch slightly closer to or
away from the Magnet, and then retighten the Screw.
Turn the Pulley for a moment. Repeat these actions
until the console displays correct feedback. When the
Reed Switch is correctly adjusted, reattach the front
shields and the left pedal.
HOW TO ADJUST THE DRIVE BELT
I
f the pedals slip while you are pedaling, even while
the resistance is adjusted to the highest setting, the
b
elt may need to be adjusted.
To adjust the belt, you must first remove the right
pedal and the right front shield. Using an adjustable
wrench, turn the right pedal counterclockwise and
remove it.
Next, remove all the screws from the left and right
front shields; there are two sizes of screws in the
front shields–note which size of screw you remove
from each hole. Then, gently pull the right front shield
away from the frame.
Next, loosen the M6 x 20mm Hex Screw (105). Then,
tighten the M10 x 50mm Hex Screw (103) until the
Drive Belt (47) is tight.
When the Drive Belt (47) is tight, tighten the M6 x
20mm Hex Screw (105).
Then, reattach the front shields and the right pedal.
MAINTENANCE AND TROUBLESHOOTING
46
57
29
30
47
103
105
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reebok TRAINER RX 3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reebok TRAINER RX 3.0 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info