559711

Reebok RX 6200 TREADMILL Manual

7
Zoom out
Zoom in
Previous page
1/34
Next page
4. Raise the treadmill to the storage position (see HOW TO
FOLD THE TREADMILL FOR STORAGE on page 21).
Have a second person hold the treadmill in the upright posi
-
tion. Position the U-base (20) against the base of the
Uprights (65) as shown,
with the Bumpers (98) under the
U-base. Finger tighten two 2” Bolts (26) with Base
Washers (35) into the base of the Uprights and the U-base.
Then, attach the U-base with two 3” Bolts (23), two Base
Washers (35), and two Nuts (13). Tip the treadmill forward if
necessary. Tighten the two 2” Bolts.
5. Make sure that all parts are properly tightened before
you use the treadmill. Place a mat beneath the tread-
mill to protect the floor. For your benefit, familiarize your-
self with the information on pages 23 and 24.
13
23
20
98
98
65
4
13
26
55
69
5
70
3
72
68
62
10
Hole
3. (Note: The parts shown in this step may be preassembled
but may need to be adjusted.) With the help of a second per-
son, raise the Frame (55) and hold it. Insert the Left Frame
Guide (68) into the left side of the Frame. Remove the Lock
Knob (67) from the Lock Pin (72). Be sure the Lock Pin
Collar (70) and the Spring (69) are on the Lock Pin. Insert
the Lock Pin into the Frame and the Left Frame Guide.
Press the Latch Insert (5) onto the Frame, with the Lock Pin
in the center hole. Tighten the Lock Knob onto the Lock Pin.
Align the Lock Pin (72) with the hole in the Left Foam Grip
(62) by sliding the Left Frame Guide (68) up or down.
Make sure that the Lock Pin can be inserted fully into the
hole. Hold the Left Frame Guide in place and tighten two
1/2” Screws (10) into the Latch Insert and the Left Frame
Guide. Note: It may be necessary to pull the Lock Knob
(67) to access and tighten the Screws.
67
35
35
23
26
If you purchase the optional chest pulse sensor (see page
20), follow the steps below to install the receiver and the
short jumper wire included with the chest pulse sensor.
1. Make sure that the power cord is unplugged. Remove the
indicated Screws (40) from the Console Back (117). Remove
the Console Back.
2. Connect the Short Jumper Wire (A) to the wire on the
Receiver (B). Connect the other end of the Short Jumper
Wire to the PULSE jack on the back of the Console (80).
Turn the Receiver (B) so the cylinder is on the side
shown, and hold the Receiver against the back of the
Console (80). Attach the Receiver with the two Small
Screws (C) included with the receiver.
Make sure that no wires are pinched. See step 1.
Reattach the Console Back (117) with the Screws (40). You
may discard the other wires included with the receiver.
40
C
117
80
A
B
40
1
Cylinder
2
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reebok RX 6200 TREADMILL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reebok RX 6200 TREADMILL in the language / languages: English as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info