801451

Redfire 86032 Cancun Manual

3
Zoom out
Zoom in
Previous page
1/14
Next page
THIS FIREBOWL MUST HAVE SAND INSERTED INTO THE BASE BEFORE USE.
THIS FIREBOWL MUST BE CURED PRIOR TO USE – SEE INSTRUCTIONS BELOW.
DO NOT OVERLOAD WITH WOOD FUEL OR HEAT LOGS.
DO NOT OVERHEAT OR USE AS A GARDEN FURNACE.
DISCOLOURATION OF THE PAINT WILL OCCUR AFTER USE AND WHEN PLACED OUTDOORS.
THE USE OF AN REDFIRE PROTECTIVE COVER IS HIGHLY RECOMMENDED.
DO NOT ALLOW RAINWATER TO POOL IN THE UNIT.
IMPORTANT - Remove any packaging before use, but retain the safety instructions. Do not remove the sticky
warning label from the stand.
PARTS LIST
A- Firebowl
B- Firebowl Stand
C- Lid
ASSEMBLY OF FIREBOWL
Ensure that the Firebowl is positioned on a permanent flat, level, heat resistant non-flammable surface away
from flammable items.
Ensure Firebowl has a minimum of 2m overhead clearance and has a minimum of 2m clearance from other
surrounding items.
Decide on the location and place on the stand. The assembled Firebowl is heavy and it is recommended the
unit is not moved once positioned or while in use. If moved, use two persons to lift and do not drag across the
floor. Ensure the model is stable prior to use.
Before use, place a minimum layer of 8cm of normal (building) sand in the base. This will help protect the
Firebowl from excessive heat and cracking.
Fuel must not be burnt directly on the Firebowl base.
The Firebowl has been pre-treated with sealant but regular retreating throughout the season with a protective
seal for ceramics is recommended to extend the life and to help protect the product from weathering.
This Firebowl requires curing before use. (SEE BELOW)
The unit may be left outside all year if an Redfire Protective Cover is used to help protect it from cold weather.
In very cold spells (below -3°C), it is recommended your Firebowl also be moved into a shed, garage or under
cover.
The Firebowl surface will age and discolor naturally from first use – this is to be expected.
DO NOT allow rain water to pool in the Firebowl.
CURING THE FIREBOWL
To start a fire, place a small quantity of kindling wood and rolled newspaper in the unit on top of the sand.
Using heat resistant gloves, light the paper and allow a flame to build up. Once sufficiently alight add a small
log and allow to burn slowly. Allow the log to burn out and the Firebowl to cool.
Repeat this procedure at least twice more. This seals any pores with soot and cures the Firebowl. You can then
build larger fires using a couple of logs. This is sufficient and produces enough heat.
DO NOT overload the unit with fuel (untreated wood or logs) or Heat Logs – if the fire is too intense this could
damage the Firebowl.
Fuel should never protrude from the top of the Firebowl.
STARTING A FIRE AFTER THE UNIT HAS BEEN FULLY CURED
To start a fire, place a small quantity of kindling wood and rolled newspaper in the unit on top of the sand.
Using heat resistant gloves, light the paper and allow a
flame to build up. Once sufficiently alight, add a small log and further logs as and when required.
DO NOT use charcoal in the Firebowl.
DO NOT overload the unit with fuel (untreated wood or logs)– if the fire is too intense this could damage the
Firebowl.
Fuel should never protrude from the top of the Firebowl.
EXTINGUISHING
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Redfire 86032 Cancun at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Redfire 86032 Cancun in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info