597822
144
Zoom out
Zoom in
Previous page
1/165
Next page
Build 31 v31.6.16 Beta
JUNE 22, 2011 © 2007-2011 RED.COM INC.
143
NOTE: Displays TINT if camera is not in master / slave configuration; displays TINT, S TINT, S
WBAL, and S FLUT if cameras are in master / slave configuration.
NOTE: S TINT, S WBAL, and S FLUT provide an offset for the slave camera relative to the common
TINT, WBAL and FLUT values programmed from the Master camera. This compensates for any co-
lorimetry differences between the transmitted and reflected light paths of an optical beam-splitter.
SHUTTER MODE and SYNCRO commands
GENLOCK enable / disable command
VARISPEED and RAMP commands
TIMELAPSE commands
LOOK commands (excluding FLUT parameter)
ZEBRA 1/2 set up and enable / disable commands
MEDIA FORMAT, CHANGE, RESET, and UNMOUNT commands
PROJECT RESOLUTION, QUALITY and REDCODE command
JAM SYNC enable / disable command
FRAME GUIDE and USER AREA setup commands
NOTE: X POSN and Y POSN offset programmed for User Action or Title from the Master camera
will result in an equal but opposite offsets for the Slave camera.
TEST SIGNAL commands
USER KEY 3, 4 set up and enable / disable command
USER KEY 5 set up and enable / disable command
FORMTATTING MEDIA
After making sure the master and slave camera each have the same size media attached, use the master
camera to format the media. Refer to APPENDIX B: MANAGING DIGITAL MEDIA.
RECORDING
The master camera initiates recording of the master AND slave cameras. Recording CANNOT be initiated
by the slave camera.
RECORD: Using RECORD key, the slave camera will enter record within +/- 2 frames of master.
GPI: Under GPI trigger, the Slave camera will enter record within +/- 1 frame of Master. This trigger must
be set up on each camera individually before powering down, connecting cameras together and powering
back up.
CLIP NAMING CONVENTIONS
CAMERA POSITION / SLATE / CAMERA ID
Under SYSTEM MENU CONTROLS > SETUP > PROGRAM > POSITION, when Master is set to CENTER,
Master and Slave clips are both labeled "C", if Master is set to LEFT, Master clips are labeled "L" and
144


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Red One 31.6.16 - 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Red One 31.6.16 - 2011 in the language / languages: English as an attachment in your email.

The manual is 12,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info