597822
141
Zoom out
Zoom in
Previous page
1/165
Next page
Build 31 v31.6.16 Beta
© 2007-2011 RED.COM INC. JUNE 22, 2011
140 140
APPENDIX E: MASTER / SLAVE CAMERA CONFIGURATION
When cameras are connected in the master / slave configuration, the user interface will display M for the
Master camera and S for the Slave camera. The slave camera CANNOT initiate recording. The slave cam-
era clip name is forced to use the master camera's I.D.
It is not recommended to mix a MYSTERIUM with a MYSTERIUM X camera. Use either both MYSTERIUM
or MYSTERIUM X cameras when recording 3-D footage.
PREPARATION
Before connecting cameras together, decide which camera will be the master and which will be the slave.
Ideally the master camera will be the one easiest to adjust once mounted in the configuration used during
recording. In addition to the basic setup of the cameras as outlined in BASIC OPERATION > FIRST TIME
USE SETTING UP YOUR RED ONE make adjustments to master and slave cameras as necessary be-
fore powering down, connecting the two cameras together and powering up again.
CAMERAS: Ensure that both master and slave cameras are either MYSTERIUM or MYSTERIUM X.
DO NOT mix cameras.
CAMERA BUILD: Ensure both cameras are on the same build. Upgrade camera firmware on both if
necessary. Refer to APPENDIX A: UPGRADING CAMERA FIRMWARE.
MEDIA: Ensure that both master and slave cameras are using identical size media. Media is formatted
using master camera after connected together. When formatting media, ensure that both master and
slave cameras have media attached.
NOTE: CHANGE REEL # and RESET REEL # functions only work for the master camera when in
master / slave mode. When a FORMAT is performed under CHANGE or RESET, the master
camera will format the slave camera media, incrementally advancing it to the next reel number.
FLUT: FLUT parameter remains independent on slave camera when in master / slave mode. Ensure
FLUT is set-up on slave camera as desired. FLUT offset can be adjusted after cameras are connected
together and rebooted.
AUDIO: Audio parameters remain independent on slave camera when in master / slave mode. Ensure
audio is set-up on both cameras as desired.
GPI: Program GPI triggers for master and slave cameras.
141


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Red One 31.6.16 - 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Red One 31.6.16 - 2011 in the language / languages: English as an attachment in your email.

The manual is 12,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info