597814
45
Zoom out
Zoom in
Previous page
1/168
Next page
Version 1.4.0 SVN 29352 BETA
©2011 RED.COM INC. APRIL 19, 2011
44 44
3. Press upwards on retainer (C) to release battery.
4. Remove battery from side handle.
REAR BATTERY MODULE
Attach a Rear Battery Module and insert one or more REDVOLT or REDVOLT XL batteries.
RED BRICK
Attach to the camera using a V-Plate and adaptor cable (p/n 140- 0135) to the DC IN connector.
DC POWER
Connect a DC power source to the camera in one of the following ways:
x Plug the RED AC Power Adapter into AC power, and the LEMO connector to the DC IN connector.
x Plug the RED CHARGER into AC power, and the LEMO connector to the DC IN connector via an
adaptor cable (p/n 140-1060).
x Plug a 12V XLR based power source into the DC IN connector via an adaptor cable (p/n 140-1060).
NOTE: The maximum sustainable power load of the EPIC AC Power Adapter is 150W (15V@10A).
The output of the adapter is over current protected, and will shut down if an excess load condition
occurs. If the output trips for any reason, remove any external loads from the camera, such as
lights, motors etc, turn off the Adapter and repeat the above procedure.
2. POWER UP
Locate the camera’s Power ON / OFF button on the right face of the Brain. If the Power Status LED is
illuminated Red, depress and then release the Power / Record button. If not illuminated, check your
battery charge status or external power source cable connection. Once powered up the Power Status
LED will illuminate Green, confirming the camera is ready to use.
3. PREPARING TO RECORD
Before each days recording, the camera should be prepared as follows:
- Physically set-up camera as desired.
- Verify camera is using the latest firmware version at www.RED.com/support and if appropriate,
upgrade the camera firmware. Refer to APPENDIX A: UPGRADING CAMERA FIRMWARE.
- Insert a blank (or previously used but erasable) REDMAG 1.8” SSD and format it.
- Perform a BLACK CALIBRATUION of the Sensor.
- Check your PROJECT SETTINGS (Time Base, Record Resolution, Record Quality, etc.).
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Red Epic - 1.4 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Red Epic - 1.4 2011 in the language / languages: English as an attachment in your email.

The manual is 8,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info