467348

Raymarine Ray49E Marine VHF Radio Manual

20
Zoom out
Zoom in
Previous page
1/116
Next page
20 Ray49E Marine VHF Radio
Power
The red and black Power Cord provides connection to DC power. Slide the bullet
connectors on the cord into their mates (with the same colored wire) on the rear
of the radio. Connect the stripped wires on the Power Cord to the nearest primary
source of the boat's DC power. A suitable source would be a circuit breaker on the
power panel or a fuse block near the unit, rated at 10 amps. Connect the red wire
to the positive terminal of the power source and the black wire to the negative
(ground) of the power source. The red and black wires each contain an in-line fuse
rated at 10A, 250V, slow-blow. If the fuses ever need to be replaced, be sure to use
the same type and rating.
The power cord must be long enough to reach the DC power source. If additional
wire length is required, the cable can be extended by adding more cable as
necessary. However, for power cable runs longer than 15 feet, larger wire
diameter size should be used to prevent voltage line loss. To ensure adequate
current draw to the equipment, Raymarine recommends that you use lugs to
connect the power cable to the DC supply and that the lug connections be both
crimped and soldered.
The Ray49E is designed to be operated on a 12 volt (nominal) system. If battery
voltage drops below 10.5 VDC, BATTERY LOW appears on the LCD. Discon-
tinue using the radio if a low voltage condition occurs as performance would be
unreliable. If voltage increases to 15.8 VDC, BATTERY HIGH appears.
External Speaker
Connect the yellow(+) wire and green (–) wire to the speaker observing polarity
as it is marked on the speaker.
NMEA Data
The Ray49E accepts NMEA 0183 (V3.01) data from a position determining device
(GPS) to provide the Latitude and Longitude position information. This
information appears on the radio’s LCD display and is also transmitted during a
DSC Distress Call. When a valid NMEA signal is detected, the “GPS” indicator
appears on the LCD. When no NMEA signal is detected, the indicator shows “NO
GPS”.
Connect the NMEA OUT + and NMEA OUT – signals from the positioning device
to the NMEA IN + (gray) and NMEA IN – (purple) wires, respectively, from the
radio. An example of how to make the connections using a suitable connector
block is shown in the following drawing. For specific instructions how to connect
your particular GPS, please refer to the handbook that came with that device.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Raymarine Ray49E Marine VHF Radio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Raymarine Ray49E Marine VHF Radio in the language / languages: English as an attachment in your email.

The manual is 4,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info