657006

Raymarine Ray 215E Manual

124
Zoom out
Zoom in
Previous page
1/128
Next page
RAY215E
Modular
VHF Radio
Owner’s
Handbook
Document number: R49018_1
Date: February 2002
RAY215_EURO Cover.p65 2/14/2002, 3:49 PM1
RAY215_EURO Cover.p65 2/14/2002, 3:49 PM2
i
Purpose
This handbook contains very important information on the installation,
operation, and maintenance of your new equipment. To get the best results
in operation and performance, please take the time to read this handbook
thoroughly.
RAY215E
The RAY215E is a VHF radiotelephone that, when outfitted with the
optional full function handset, includes equipment for Class “D” Digital
Selective Calling. It is intended for general communication within the
Maritime Mobile Service worldwide and is for use on non-SOLAS vessels.
LicenseLicense
LicenseLicense
License
Regulations in some areas require that you obtain an operator license before
operating VHF radio equipment. It is your responsibility to determine
whether a license is required in your area before operating this equipment.
Maritime Mobile Service Identity (MMSI)Maritime Mobile Service Identity (MMSI)
Maritime Mobile Service Identity (MMSI)Maritime Mobile Service Identity (MMSI)
Maritime Mobile Service Identity (MMSI)
An MMSI number is required to operate the Digital Selective Calling
(DSC) equipment in this radio. In some areas, a radio operator license is
required before an MMSI number will be issued. You can request an MMSI
number from the same agency that issues radio operator licenses in your
area. You can then program the MMSI number into your RAY215E using
the Menu Operation described in this handbook. If regulations in your
area do not permit you to program the MMSI number yourself, your
Raymarine dealer can program the number for you.
Automatic Automatic
Automatic Automatic
Automatic
TT
TT
T
ransmission Identification System (Aransmission Identification System (A
ransmission Identification System (Aransmission Identification System (A
ransmission Identification System (A
TIS)TIS)
TIS)TIS)
TIS)
Your RAY215E can activate the ATIS feature, if needed. You can request
an ATIS number from the same agency that issues radio operator licenses
in your area. You can then program the ATIS number into your RAY215E
using the Menu Operation described in this handbook. If regulations in
your area do not permit you to program the ATIS number yourself, you
can have your dealer program the number for you. You must only enable
this feature when operating the radio in the inland waterways of European
countries that require automatic identification transmission.
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM1
ii
SAFETY NOTICE
This device is only an aid to navigation. Its performance can be affected
by many factors including equipment failure or defects, environmental
conditions, and improper handling or use. It is the user's responsibility to
exercise common prudence and navigational judgement, and this device
should not be relied upon as a substitute for such prudence and judgement.
Your Raymarine VHF radio generates and radiates radio frequency (RF)
electromagnetic energy (EME). This equipment must be installed and
operated in accordance with the instructions contained in this handbook.
Failure to do so can result in personal injury and/or product malfunction.
Antenna Mounting and EME ExposureAntenna Mounting and EME Exposure
Antenna Mounting and EME ExposureAntenna Mounting and EME Exposure
Antenna Mounting and EME Exposure
For optimal radio performance and minimal human exposure to radio
frequency electromagnetic energy, make sure the antenna is:
• connected to the radio before transmitting
• properly mounted
• located where it will be away from people
• located at least three feet (91cm) from the RAY215E and the microphone/
handset
Adjustments or RepairAdjustments or Repair
Adjustments or RepairAdjustments or Repair
Adjustments or Repair
Adjustments require specialized service procedures and tools only
available to qualified service technicians – there are no user serviceable
parts or adjustments. The operator should never remove the cover or
attempt to service the equipment.
Raymarine products are supported by a network of Authorized Service
Representatives. For product information you may contact the following
regional centers:
United States Raymarine, Inc.
22 Cotton Road, Unit D
Nashua, NH 03063-4219
USA
Telephone: 603-881-5200
800-539-5539
Fax: 603-864-4756
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM2
iii
Europe Raymarine Ltd
Anchorage Park
Portsmouth, Hampshire
England PO3 5TD
Telephone: +44 (0) 23 9269 3611
Fax: +44 (0) 23 9269 4642
© Raymarine, Inc. 2001
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM3
iv
Certificate No.
RT015
We Raymarine Limited Anchorage Park
Portsmouth
Hampshire
England P03 5TD
declare, under our sole responsibility, that the products identified in this declaration, and to which this
declaration relates, are in conformity with the essential requirements of European Parliament and Council
Directive:
1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity.
Product Name: Raymarine RAY 215E VHF Radio
with optional Class "D" DSC
Product Number(s): E43004
Product Option: Full Function Handset (DSC enabled)
Product Number(s): E46020
E46022 (includes second station kit)
The products have been assessed to Conformity Procedure Annex IV of the Directive and by application of the
following standard(s):
EMC EN 60945 : 1997
Safety EN 60945 : 1997
Technical characteristics EN 300 162 Part 2
EN 301 025 Part 2 and Part 3
EN 300 698 Part 2 and Part 3
The assessment is consistent with a Technical Construction File showing conformity with the essential
requirements of the Directive and has been reviewed by Notified Body No. 0191.
The product is labelled with the CE conformity marking, the identification number of the Notified Body and
class identifier.
Signatory: Name Adil Abbas
Title EMC Manager
Company Name Raymarine Limited
Company Address Anchorage Park
Portsmouth, Hampshire
England PO3 5TD
Signature ________________________
Date 07 February 2002
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM4
v
Table of Contents
Section 1 General Description
1.1 Introduction ......................................................................... 1-1
1.2 Equipment Features ............................................................. 1-1
1.3 Minimum Function Handset /
Full Function Handset Options............................................ 1-2
Section 2 Installation
2.1 Unpacking and Inspection ................................................... 2-1
2.2 Equipment Supplied............................................................. 2-1
2.2.1 Optional Accessories.............................................. 2-1
2.3 Planning the Installation ...................................................... 2-2
2.3.1 Typical Mounting Methods .................................... 2-2
2.3.2 Flush Mounting ...................................................... 2-3
2.4 Electrical Connections ......................................................... 2-6
2.4.1 DC Power and External Speaker Connections ...... 2-6
2.4.2 External Speaker Connections ............................... 2-7
2.4.3 NMEA Data ........................................................... 2-8
2.4.4 Antenna Connections ............................................. 2-8
2.4.5 Antenna Mounting Suggestions............................. 2-9
2.4.6 Grounding .............................................................. 2-9
Section 3 Operation with Minimum Function Handset
3.1 Introduction ......................................................................... 3-1
3.1.1 DSC and NMEA Operation ................................... 3-1
3.2
Minimum Function Handset and Handset Priority................
3-1
3.3
Handset Connections .............................................................
3-2
3.4 Control and LCD Display .................................................... 3-3
3.4.1 Controls .................................................................. 3-3
3.4.2 LCD Display .......................................................... 3-6
3.5 Operating Procedures .......................................................... 3-8
3.5.1 Turning the Power On ............................................ 3-8
3.5.2 Setting the Squelch................................................. 3-8
3.5.3 Setting the Volume ................................................. 3-8
3.5.4 Setting the Power Output ....................................... 3-8
3.5.5 Setting the Channel ................................................ 3-9
3.5.6 Selecting the Private Channel ................................ 3-9
3.5.7 Setting the Frequency Mode ................................ 3-10
3.5.8 Transmitting ......................................................... 3-10
3.5.9 Selecting a Weather Channel ................................3-11
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM5
vi
3.5.10 Priority Channel ....................................................3-11
3.5.11 Channel Memory...................................................3-11
3.5.12 Resetting Factory Defaults....................................3-11
3.5.13 Scan Modes .......................................................... 3-12
3.5.14 Monitor Mode ...................................................... 3-13
3.5.15 Multi-Call Operation............................................ 3-14
3.5.16 LCD Backlight Function ...................................... 3-14
3.5.17 NMEA Operation ................................................. 3-15
3.5.18 Digital Selective Calling (DSC).......................... 3-16
3.5.18.1 MMSI Number Setup .................................... 3-17
3.5.18.2 Individual Ship's Call .................................... 3-19
3.5.18.3 All Ships Call ................................................ 3-26
3.5.18.4 Group Call ..................................................... 3-27
3.5.18.5 Distress Call .................................................. 3-28
3.5.18.6 Distress Relay Call ........................................ 3-30
3.5.19 ATIS ID No. Entry ............................................... 3-30
Section 4 Operation with Full Function Handset
4.1 Introduction ......................................................................... 4-1
4.2 Full Function and Minimum Function Handset Priority ..... 4-1
4.3 Handset Connections ........................................................... 4-2
4.4 Control and LCD Display .................................................... 4-3
4.4.1 Controls .................................................................. 4-3
4.4.2 LCD Display .......................................................... 4-7
4.5 Radio Functions ................................................................... 4-9
4.6 Operating Procedures ........................................................ 4-10
4.6.1 Setting the Volume ............................................... 4-11
4.6.2 Setting the Squelch................................................4-11
4.6.3 Using the Function Key ........................................4-11
4.6.4 Setting the Frequency Mode .................................4-12
4.6.5 Receiving on the Weather Channels .................... 4-13
4.6.6 Selecting the Channel........................................... 4-13
4.6.7 Selecting the Private Channel .............................. 4-14
4.6.8 Priority Channel ................................................... 4-15
4.6.9 Multi-Call Operation............................................ 4-16
4.6.10 Channel Memory.................................................. 4-16
4.6.11 Setting the Transmission Power Output ............... 4-17
4.6.12 Desensitized Reception (Local Mode)................. 4-17
4.6.13 LCD Backlight Function ...................................... 4-17
4.6.14 Intercom Mode ..................................................... 4-18
4.6.15 Scan Mode ........................................................... 4-19
4.6.16 Monitor Mode ...................................................... 4-20
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM6
vii
4.6.17 NMEA Operation ................................................. 4-21
4.6.18 Digital Selective Calling (DSC)........................... 4-23
4.6.18.1 Individual Call to Another Ship
(Ship-to-Ship)................................................ 4-23
4.6.18.2 Individual Call to Shore Station
(Ship-to-Shore).............................................. 4-26
4.6.18.3 Receiving an Individual Call......................... 4-29
4.6.18.4 Transmitting a Group Call ............................. 4-30
4.6.18.5 Receiving a Group Call ................................. 4-31
4.6.18.6 Transmitting an All Ships Call ...................... 4-32
4.6.18.7 Receiving an All Ships Call .......................... 4-33
4.6.18.8 Transmitting a Distress Call .......................... 4-33
4.6.18.9 Receiving a Distress Call .............................. 4-37
4.6.18.10 Receiving a Distress Relay Call .................... 4-38
4.6.19 ATIS Operation .................................................... 4-39
4.7 Menu Operation ................................................................. 4-39
4.7.1 Selecting the Menu Operation ............................. 4-39
4.7.2 NAVSTAT Operation ........................................... 4-40
4.7.3 DSC Operation..................................................... 4-41
4.7.3.1 Selecting Distress Call Type (NATURE) ...... 4-41
4.7.3.2 Manual Entry of Latitude/Longitude
(L/L ENT)...................................................... 4-43
4.7.3.3 Modifying the MMSI Number List
(PHNBOOK)................................................. 4-45
4.7.3.4 Modifying the MMSI Group Number
(GROUP)....................................................... 4-50
4.7.4 Setting Operation ................................................. 4-52
4.7.4.1 Setting ATIS ID Number ............................... 4-52
4.7.4.2 Setting MMSI Number.................................. 4-55
4.7.4.3 ATIS Set Up .................................................. 4-58
Section 5 Maintenance
5.1 How to Contact Raymarine.................................................. 5-1
5.2 Preventive Maintenance....................................................... 5-3
5.3 Specifications....................................................................... 5-3
5.4 Drawings .............................................................................. 5-7
Section 6 Appendix
6.1 International Channel Frequency Tables ............................. 6-1
6.2 US Channel Frequency Tables............................................. 6-4
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM7
viii
GLOSSARY OF TERMS
All Scan .......................... Scans all channels
ATIS................................ Automatic Transmission Identification
System. Used for inland waterways in some
European countries.
Canadian Channels ......... Channel designator as defined by Industry
Canada
DSC ................................ Digital Selective Calling
Dual Watch ..................... Monitor the Priority Channel (9 or 16) while
working on another channel
Duplex ............................ Transmit and receive on different frequencies
FCC ................................ Federal Communications Commission
FM .................................. Frequency Modulation
International Channels.... Channel designator as defined by the ITU
ITU ................................. International Telecommunications Union
LCD ................................ Liquid Crystal Display
Memory Scan.................. Scans only user selected memory channels
MMSI ............................. Maritime Mobile Service Identity; a number
issued by each country to identify maritime
stations.
NOAA ............................ National Oceanographic and Atmospheric
Administration
PTT switch...................... Microphone push-to-talk switch
RF ................................... Radio Frequency
RTCM ............................. Radio Technical Commission for Maritime
Services
RX .................................. Receiver
Simplex........................... Transmit and receive on the same frequency
Squelch ........................... A circuit that sets the threshold for cutting off
the receiver when the signal is too weak for
reception of anything but noise
TX ................................... Transmit
Tri-Watch ........................ Monitor the Priority Channel and Weather
Channels while working on another channel
US Channels ................... Channel designations as defined by the FCC
VCO................................ Voltage Controlled Oscillator
VHF ................................ Very High Frequency 30MHz to 300MHz
Weather Channels ........... Channels for routine and emergency weather
information broadcast by NOAA
RAY215_EURO Preface.p65 2/14/2002, 3:49 PM8
1-1
General Description
Section 1 General Description
1.1 Introduction
Congratulations on your purchase of Raymarine's RAY215E marine
radiotelephone. This handbook describes the physical and functional
characteristics of the radiotelephone.
The RAY215E is a microprocessor-controlled, digitally synthesized,
compact transceiver that provides reliable simplex and semi-duplex (two-
frequency) communications. The RAY215E provides two-way
communications on Marine channels and reception on up to 10 private
channels.
The RAY215E can transmit and receive on all available International
marine VHF radiotelephone channels. With a software upgrade, the
RAY215E can also communicate on the US channel set. Refer to the of
Frequency Tables in Section 6, which list all marine VHF channels
available in your RAY215E. You should familiarize yourself with these
tables to ensure proper channel usage.
1.2 Equipment Features
The RAY215E is designed and manufactured to provide ease of operation
with excellent reliability. The important built-in features of the equipment
are listed below.
• Exclusive circuit that automatically selects Channel 16 as the Priority
Channel when the radio is turned on
• Dedicated key for selecting the Priority Channel (16) when using another
channel
• Waterproof to CFR-46 standard for Base Station
• Waterproof to JIS-7 standard for Minimum Function Handset and
Optional Full Function Handset
• Full Class D DSC functionality (when using optional Full Function
Handset)
• Dedicated DISTRESS key on back of handset, with spring loaded
protective cover (DSC functions require Full Function Handset)
• All Scan and Memory Scan features
• ATIS
• Up to 10 Private Channels
• Multi-call operation
• Dual/Tri-Watch Monitor modes
RAY215_EURO Sect1.p65 2/14/2002, 3:59 PM1
1-2 General Description
• Intercom operation between Minimum Function Handset and Optional
Full Function Handset (second station)
• Distant/local mode
1.3 Minimum / Full Function Handset Options
The RAY215E can be operated with the standard Minimum Function
Handset, an optional Full Function Handset with additional features, or
both. Operation with both units installed enables intercom capabilities
between the two stations.
The Minimum Function Handset features up/down channel select keys,
Priority Channel (16) selection button, plus a quick access Distress key.
The optional Full Function Handset provides you with all the features of
the Minimum Function Handset plus a full alphanumeric keypad, expanded
LCD display, volume and squelch level controls, and full Class D DSC
functions, including: DSC distress calls, dedicated keys for Individual
and All Ships DSC calls, and expanded ship and shore phonebooks for
making DSC Individual calls.
Note: When a Full Function Handset is NOT installed, the radio will
have only basic functionality. You will not have access to DSC functions
or NMEA (GPS) position data operation. If ATIS is enabled, it will be
active all the time – you will not be able to disable it.
The Single Station Full Function Handset with cradle (Raymarine part
number E46020) is used in lieu of the Minimum Function Handset. The
Dual Station Full Function Handset (Raymarine part number E46022),
which includes a cradle and external speaker, is used in conjunction with
the Minimum Function Handset to enable intercom communications
between the two stations.
Note: The RAY215E is designed to have the base station as the priority
unit. Therefore, Raymarine recommends installing the base station in the
radio operation room or the location from which the ship is normally
navigated. If an optional second station Full Function Handset is also
installed, that handset should be installed in the remote location.
See Section 3 for a complete discussion of operation using the optional
Full Function Handset. Section 4 describes using the RAY215E with the
Minimum Function Handset.
RAY215_EURO Sect1.p65 2/14/2002, 3:59 PM2
2-1
Installation
Section 2 Installation
2.1 Unpacking and Inspection
Use care when unpacking the unit from the shipping carton to prevent
damage to the contents. It is also good practice to save the carton and the
interior packing material in the event you must return the unit to the factory.
2.2 Equipment Supplied
The following is a list of materials supplied with the RAY215E:
DescriptionDescription
DescriptionDescription
Description
PP
PP
P
art Noart No
art Noart No
art No
..
..
.
RAY215E Radiotelephone E43004
Minimum Function Handset with Cradle E49016
Power/Optional Speaker/NMEA Cable R49017
Mounting Yoke R49011
Yoke Knob R49012
Handbook, RAY215E E49018
Sun Cover R49014
2.2.1 Optional Accessories
The following is a list of options available for the RAY215E:
DescriptionDescription
DescriptionDescription
Description
P P
P P
P
art Noart No
art Noart No
art No
..
..
.
Single Station: E46020
Full Function Handset with Cradle
Second Station: E46022
Full Function Handset with Cradle
7 meter Handset Extension Cable
External Powered Handset Speaker
Handset/Microphone Relocation Kit E46026
5m Extension Cable, Full Function Handset E46018
10m Extension Cable, Full Function Handset E46017
3m Extension Cable, External Speaker E46015
External 10W Speaker E46006
Flush Mounting Kit E46023
8' Fiberglass VHF Antenna M51118E
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM1
2-2 Installation
2.3 Planning the Installation
When planning the installation of your RAY215E, the following conditions
should be considered to ensure dependable and trouble-free operation.
Mount the Base Station Transceiver using the Mounting Template
provided.
The Base Station Transceiver should be located in the radio telegraph
operating room or the room from which the ship is normally navigated.
The Base Station Transceiver is designed to be mounted horizontally or
vertically on a flat bulkhead below decks. Select a location that is
non-metallic, dry, protected, well-ventilated, and free from high operating
temperatures and excessive vibration. Provide sufficient space behind the
transceiver to allow for proper cable connections to the rear panel
connectors. Locate the transceiver as near as possible
to the power source yet as far apart as possible from any devices that may
cause interference such as motors, generators, and other on board
electronics. The transceiver should be protected from prolonged direct
exposure to rain and salt spray.
The transceiver is NOT designed to be mounted in engine compartments.
Do NOT install the transceiver in a location where there may be
flammable vapors (such as in an engine room or compartment, or in a fuel
tank bay), water splash or spray from bilges or hatches, where it
is at risk from physical damage from heavy items (such as hatch covers,
tool boxes, etc.), or where it might be covered by other equipment.
Locate the Base Station Transceiver and Handset at least 3 feet from the
antenna.
Mount the base station transceiver to allow easy access from the location
where the ship is normally navigated.
2.3.1 Typical Mounting Methods
The RAY215E can be conveniently mounted on a chart table, bulkhead,
overhead, or any other desired location. Refer to Figure 2-1 for typical
mounting methods.
CAUTION
Make sure there are no hidden electrical wires or other items behind
the desired location before proceeding. Check that free access for
mounting and cabling is available.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM2
2-3
Installation
Figure 2-1 Typical Mounting Methods
2.3.2 Flush Mounting
In addition to the typical Mounting Methods, the RAY215E may also be
flush mounted using the optional Flush Mount Kit. These kits are available
from your Raymarine dealer or our Customer Service Department.
There are two methods of mounting the radio using the flush mount kit:
from the front or rear of the console. Choose the method that best suits
your console.
1. Select the location for the radio transceiver. A clear, flat area, of
sufficient height having at least 9" of clear depth behind the panel is
required.
CAUTION
Make sure there are no hidden electrical wires or other items behind
the desired location before proceeding. Check that free access for
mounting and cabling is available.
2. Unpack the Flush Mount kit and confirm that all hardware is present.
3. Mark the cutout area using the cutout guide.
4. Drill a pilot hole inside of the cutout guide area.
5. Using an appropriate saw, carefully cut along the cutout line.
6. Remove the yoke knobs and the mounting yoke from the transceiver.
Check that the radio will fit into the cutout area.
Front Mounting
7. Insert the rear of the transceiver through the flush mount bracket such
that the tabs on the bracket point away from the radio’s front bezel.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM3
2-4 Installation
8. Continue to push the bracket onto the transceiver until it is flush with
the front bezel.
9. On each side of the transceiver, insert a screw through the bracket tab
and into the threaded holes from which you removed the yoke knobs.
10.Tighten the screws.
11. It is recommended to run a bead of RTV or similar sealant around the
inside edge of the bracket to avoid water entry behind the console.
12.Insert the radio and attached bracket into the cutout.
13.Install four flat head screws through the four countersunk holes in the
front of the bracket and secure into the console.
14.From behind the console, connect the power/optional speaker and
antenna cables.
Rear Mounting
7. It is recommended to run a bead of RTV or similar sealant around the
inside edge of the bezel to avoid water entry behind the console.
8. Insert the radio into the cutout until the front bezel is flush with the
console.
9. From behind the console, push the flush mount bracket over the rear
of the transceiver such that the tabs on the bracket point away from
the radio’s front bezel.
10.Continue to push the bracket onto the transceiver until it is flush with
the console.
11. On each side of the transceiver, insert a screw through the bracket tab
and into the threaded holes from which you removed the yoke knobs
but do not fully tighten at this time.
12. Install four pan head screws through the four holes in the bracket and
secure the bracket into the console.
13. From the front, make sure the transceiver is still flush with the console.
14. From behind the console, fully tighten the screws that secure the bracket
to the radio’s threaded yoke knob holes.
15.Connect the power/optional speaker and antenna cables.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM4
2-5
Installation
Figure 2-2 Outline and Mounting Dimensions
All dimensions are shown in inches and (millimeters)
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM5
2-6 Installation
Wire ColorWire Color
Wire ColorWire Color
Wire Color
FunctionFunction
FunctionFunction
Function
Connects toConnects to
Connects toConnects to
Connects to
RED Power + Ship's 13.6 VDC power
BLACK Power −
YELLOW Speaker + External speaker
GREEN Speaker −
BLUE NMEA + Input from position source (GPS, etc.)
PURPLE NMEA −
The RED (+) power wire contains a 10 amp in-line fuse.
2.4 Electrical Connections
2.4.1 DC Power and External Speaker
Connections
The 6-foot long power cable is a multi-purpose assembly containing three
wire-pairs for connections to DC power, NMEA input, and an optional
speaker. Connections to the 6-pin connector are as follows:
Figure 2-3 Power/External Speaker/NMEA Cable and 6 Pin Connector
In most cases the length of the power cable should be adequate enough to
reach the DC power source. If additional wire length is required, the cable
can be extended by adding more cable as necessary. However, for power
cable runs longer than 15 feet, larger wire diameter size should be used to
prevent voltage line loss.
Your RAY215E should be connected to the nearest primary source of ship's
DC power. A typical source may be a circuit breaker on the power panel or a
fuse block near the unit. When connecting to either of these sources, the
circuit breaker or other in-line fuse should be rated at 10 amps.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM6
2-7
Installation
Figure 2-4 Power Cable Length
It is recommended that lugs be used to connect the power cable to the DC
supply and the lug connections should be both crimped and soldered.
This is very important in order to ensure adequate current draw to the
equipment. Intermittent operation may result if an insufficient connection
is made to the power source. The connection terminal should be clean,
with no sign of corrosion.
The red (+) wire is connected to the positive terminal of the power source.
The black (-) wire is connected to the negative (ground) of the power
source. Should the power connections be inadvertently reversed, the unit
will not power up but no damage will occur. Check the polarity with a
VOM (Voltage/Ohm Meter) and reconnect observing correct polarity. If
the fuse ever needs replacement, be sure to use the same type and rating.
2.4.2 External Speaker Connections
The yellow (+) wire and green (-) wire are used for connecting the
RAY215E to an external speaker (see Figure 2-3), such as Raymarine’s
10W External Speaker (part number E46006).
Four watts of audio output power are provided for an external 4-ohm
speaker. A suitable speaker can be purchased from your local marine dealer.
Connect the yellow (+) wire and green (-) wire to the speaker observing
polarity as it is marked on the speaker. When connected, the external
speaker will function simultaneously with the internal speaker.
CAUTION: DO NOT short the green (-) wire to the yellow (+)
wire. DO NOT short the green (-) wire to the black Power (-) wire.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM7
2-8 Installation
2.4.3 NMEA Data (Requires Full Function Handset)
When an optional Full Function Handset is installed enabling Class D
DSC functionality, inputting NMEA data will provide position information
to the radio. The RAY215E accepts NMEA 0183 data from a position
determining device (GPS, etc.) to provide the Latitude and Longitude
position information that is transmitted during a DSC Distress Call.
Connect the input(s) of the positioning device to the white (NMEA+) and
black (NMEA-) wires in the Power/Optional Speaker/NMEA cable.
An example of how to connect the NMEA cables and power supply using
a suitable connector block is shown in the diagram below. For specific
instructions how to connect your particular GPS, please refer to the
handbook that came with that device.
Note: For non-differential GPS, all return connections (-) must be tied to
a common ground reference.
+12 V
0V
+ NMEA Data (white)
-- NMEA Data (black)
Red
Black
Yellow
Figure 2-5 GPS Connections
2.4.4 Antenna Connections
The coaxial VHF antenna cable connects to the RAY215E antenna cable
on the rear panel using a PL259 VHF type connector. The antenna cable
length can be critical to performance. If you are uncertain, contact a
professional installer or call Raymarine Product Support. If a longer cable
length is required, RG-58 (50 ohm) coaxial cable or equivalent cable can
be used for runs up to a maximum of 50 feet. If the distance required is
even greater, Raymarine recommends using low loss RG-213 or equivalent
cable for the entire run to avoid excessive losses in power output.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM8
2-9
Installation
If the antenna RF connector is likely to be exposed to the marine
environment, a protective coating of grease (Dow Corning DC-4 or similar)
can be applied to the connector before connecting it to the radio. Any
other extensions or adapters in the cable run should also be protected by
silicon grease and then wrapped with a waterproofing tape.
2.4.5 Antenna Mounting Suggestions
The best radio in the world is useless without a quality antenna and good
location. Mounting the VHF antenna properly is very important because
it will directly affect the performance of your VHF radio. A VHF antenna
designed for marine vessels should be used.
• Since VHF transmission is essentially Line-of-Sight, mount the antenna
at the highest possible location on the vessel and free of obstruction to
obtain maximum range.
• If you must extend the length of the coaxial cable between the antenna
and the radio, use a coaxial cable designed for the least amount of power
loss over the entire cable length.
• Remember to maintain the recommended minimum 3 feet between the
radio and antenna.
2.4.6 Grounding
While special grounding is not generally required for VHF radiotelephone
installations, it is good marine practice to properly ground all electronic
equipment to the ship's earth ground system. The RAY215E can be
connected to ground by attaching a wire to one of the screws on the unit's
rear panel and then to the nearest ship's earth ground connection point.
The recommended wire to be used for such grounding is #10 AWG.
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM9
2-10 Installation
Figure 2-6 Typical Grounding Method
RAY215_EURO Sect2.p65 2/14/2002, 3:59 PM10
3-1
Operation with Minimum Function Handset
Section 3 Operation with
Minimum Function Handset
3.1 Introduction
The RAY215E can be operated with the standard Minimum Function
Handset, or an optional Full Function Handset that enables additional
features, or both handsets to enable intercom capabilities. This section
describes using the RAY215E with the Minimum Function Handset. See
Section 4 for a full discussion of operation using the Full Function Handset.
3.1.1 DSC and NMEA Operation
The Full Function Handset enables Class D DSC operations and NMEA
(GPS) position data transmissions in the RAY215E. DSC functions
include: Individual, Group, All Ships, and Distress calls. To have DSC
and NMEA (GPS) position functionality available with a Minimum
Function Handset, you must also have installed a Second Station Full
Function Handset.
3.2 Minimum / Full Function Handset Priority
When both a Minimum Function Handset and Full Function Handset are
in use, only one can have priority to make a call. When the Full Function
Handset is out of its cradle, it has priority over the Minimum Function
Handset and the REMOTE indicator illuminates on the LCD of the base
station. When the Full Function Handset is in the cradle, the Minimum
Function Handset has priority and the REMOTE indicator extinguishes.
Overriding the Full Function Handset
In an emergency, the fist microphone / base station can override the full
function handset to make a call even though the handset has priority (is
off the cradle). To override the handset, press and hold the DSC/PRI key
on the base station. The REMOTE indicator flashes and the base station
regains priority control. Make your call as usual using the fist microphone.
On the full function handset, OVERRIDE appears on the dot matrix
display. In this mode, all keys are disabled on the handset except for
DISTRESS. The base station retains control until the DSC/PRI key is
again pressed and held.
RAY215_EURO Sect3.p65 2/14/2002, 4:00 PM1
3-2 Operation with Minimum Function Handset
Note: The RAY215E is designed to have the base station as the priority
unit. You should install the base station and Minimum Function Handset
in the radio operation room or the location from which the ship is normally
navigated. If an optional second station Full Function Handset is also
installed, that handset is the one that should be installed in the remote
location.
3.3 Handset Connections
The Minimum Function Handset can be connected to the port on the front
of the base station (Figure 3-2) or mounted near the base station using the
optional Handset Relocation Kit (part number E46026), which is available
from your authorized Raymarine dealer/distributor. The Relocation Kit
must be connected to the HANDSET/RELOCATION KIT port on the
rear of the base station (Figure 3-1).
If both a Minimum Function Handset and Second Station Full Function
Handset are to be used, the Minimum Function Handset must be connected
to the front port with the Full Function Handset connected to the
HANDSET/RELOCATION KIT port on the rear. In this case, the Handset
Relocation Kit could not be used with the Minimum Function Handset.
Once installed, the two stations can communicate with one another using
the Intercom function described in section 4.6.14.
Figure 3-1 Rear Connections
RAY215_EURO Sect3.p65 2/14/2002, 4:00 PM2
3-3
Operation with Minimum Function Handset
1
7654
231098
11
12
13
14
15
Figure 3-2 Layout of Controls
3.4 Control and LCD Display
3.4.1 Controls
Several of the buttons on the front panel of the base station serve
multiple purposes. For the most part, the function indicated on the
first line of the button is accessed by pressing and releasing that
button. The function indicated on the second line of the button is
accessed by pressing and holding the button for two seconds.
CH (Channel Selection) Knob
This knob selects the active channel. Turning the knob clockwise
increments the channel number. Turning the knob counterclockwise
decrements the channel.
The knob is also used to select values and functions in DSC mode.
VOLUME/PWR Knob
This knob switches power on and off and controls the audio volume.
From the OFF position, rotating the knob clockwise until it "clicks"
powers ON the radio. Continuing to turn the knob clockwise, the
volume increases. Rotating the knob counterclockwise, the volume
decreases. Continuing to turn the knob counterclockwise, the unit
"clicks" OFF.
The upper bar graph on the LCD displays the volume level.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM3
3-4 Operation with Minimum Function Handset
!
SQUELCH Knob
This knob controls the squelch sensitivity level. Rotating the knob
clockwise increases the squelch level. Rotating the knob
counterclockwise decreases the squelch.
The lower bar graph on the LCD displays the squelch level.
"
SCAN/ MEM Key
This key starts or stops All Scan and Memory Scan Modes. The key
also places favorite channels into the radio's memory for quick
selection.
Pressing and holding SCAN/MEM for 3 seconds stores into memory
the currently displayed channel and illuminates the MEM indicator
on the LCD. If the current channel has already been stored, pressing
SCAN/MEM removes the channel from memory and extinguishes
the MEM indicator.
Pressing and releasing SCAN/MEM when no channels have been
entered into memory initiates a scan of all available channels. The
SCAN indicator illuminates on the LCD.
When at least one channel has been programmed into memory,
pressing and releasing SCAN/MEM causes the MEM and SCAN
indicators to flash for 3 seconds. If the key is pressed again while
these indicators are flashing, the radio enters All Scan mode.
However, if the 3 seconds expire before pressing the key a second
time, the radio initiates a scan of only those channels programmed
into memory.
Pressing the SCAN/MEM key during All Scan or Memory Scan
terminates the scan.
#
MULTI Key
Pressing and releasing MULTI switches between the Multi channel
and the last used marine channel. Pressing and releasing MULTI
while in the Dual Watch mode places the unit in Tri-Watch mode.
While in either Multi or Tri-Watch modes, the MULTI indicator
illuminates on the LCD.
Pressing and holding MULTI and SCAN/MEM key switches between
the International and US frequency groups, if your radio has been
upgraded to include US group channels. While in the International
Frequency mode, the INT indicator illuminates on the LCD. There is
no indicator for US mode.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM4
3-5
Operation with Minimum Function Handset
$
MON/ 1/25 Key
Pressing and releasing MON/1/25 initiates the Dual-Watch Monitor
mode.
Pressing and holding MON/1/25 for 2 seconds toggles the output
power between 1 and 25 watts. While in the 1 Watt mode, the 1W
indicator illuminates on the LCD.
Pressing this button while holding PTT overrides the 1W output
setting. See the Frequency tables in section 6 for the affected channels.
%
16 Key
Pressing and releasing 16 switches the radio between the current
channel and the Priority Channel.
&
D/L
//
//
/ I.C. Key
Pressing and releasing D/L / I.C. switches receiver sensitivity between
Distant (full) and Local (desensitized) modes.
While in the Local mode, the DESENS indicator is illuminated.
Holding D/L / I.C. for 2 seconds toggles on and off the Intercom
function between the microphone on the base station and an optional
remote full function handset. Press PTT to converse with the other
station.
'
DSC/ PRI Key
Pressing and releasing the DSC/PRI key by itself has no effect.
Pressing and releasing the DSC/PRI and D/L / I.C. keys
simultaneously places the radio in DSC mode, which is used to make
Individual Ship’s, All Ships, Group, and Distress Calls.
Note: An optional Full Function Handset must be installed to enable
the Class D DSC functionality.
Pressing and holding DSC/PRI for 2 consecutive seconds returns
priority control from an optional second station full function handset
to the base station. This feature is for immediately taking radio
operation control from the second station in case of an emergency.
DIM Key
Pressing this key once starts Dimmer mode, which adjusts the
brightness of LCD's backlight.
Each successive press of the DIM key switches the brightness from
Off, to Low, to Medium, to High, then back to Off.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM5
3-6 Operation with Minimum Function Handset
Channel UP Key
This key increments the channel number by 1 each time it is pressed.
If pressed and held, the channel increments at a rate of 10 channels
per second.
Channel DOWN Key
This key decrements the channel number by 1 each time it is pressed.
If pressed and held, the channel decrements at a rate of 10 channels
per second.
!
DISTRESS Key (under hinged door on rear of handset)
The DISTRESS key sends a DSC Distress Call when pressed and
held for 5 seconds. The DISTRESS button operates only when
an optional second station full function handset is also installed.
"
PTT Key
Pressing the PTT (Push To Talk) key enables the radio's transmitter.
PTT key operation is disabled when the selected channel is a
disallowed channel.
The radio is equipped with a 5 minute timeout timer as a safety feature.
After the PTT has been held continuously for 5 minutes, transmission
is discontinued and an alarm sounded until PTT is released.
#
16 Key
Has the same function as the 16 key on the front panel controls
3.4.2 LCD Display
The following describes the functional characters on the RAY215E's LCD.
Figure 3-3 LCD Display Layout
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM6
3-7
Operation with Minimum Function Handset
NMEA indicator
Appears in every operation mode when valid NMEA data is being
received. (Applicable only with Optional Function Handset)
DSC indicator
Appears when the radio is in the DSC mode, when an optional Full
Function Handset is installed enabling the Class D DSC functionality.
!
ACK indicator
Appears when receiving an acknowledgment to a DSC Distress Call
or Individual Call, when an optional Full Function Handset is installed
enabling the Class D DSC functionality.
"
INT indicator
Appears when the International frequency group is selected.
#
MULTI indicator
Appears when the radio is in the Multi-call mode or a Multi-call
channel is selected.
$
TX indicator
Appears during transmission.
%
1W indicator
Appears when the current transmission output is set at 1W.
(The indicator is extinguished when the output is set at 25W.)
&
MEM indicator
Appears when a channel on the display is stored in memory and
during a Memory Scan operation.
'
SCAN indicator
Appears during a scan operation.
DESENS indicator
Appears when the radio is in the Desensitized (local) mode.
MON indicator
Appears when the radio is in the Dual Watch or Tri-Watch Monitor
mode.
WX indicator (requires US Frequency Group upgrade)
Appears when the radio is in the Weather Channel or Tri-Watch modes
(Applicable only in US Frequency mode when this option has been
installed.)
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM7
3-8 Operation with Minimum Function Handset
!
REMOTE indicator
Appears when the optional, remote full functional handset has the
priority operation.
"
Channel display (Large)
Displays the current channel number.
#
Channel display (Small)
Displays the Priority Channel number while the radio is in the Monitor
mode and function indicators during DSC mode.
$
VOL indicator (in bar graph)
Represents the current sound volume level. A louder volume displays
a larger number of segments in the bar graph.
%
SQL indicator (in bar graph)
Represents the current squelch level. A deeper squelch displays a
larger number of segments in the bar graph.
&
ATIS indicator
Appears when the ATIS (automatic identification transmission)
feature is turned on.
3.5 Operating Procedures
3.5.1 Turning the Power On
Rotate the VOLUME/PWR knob clockwise to turn the radio on.
3.5.2 Setting the Squelch
Rotate the SQUELCH knob counterclockwise until audio is heard. Rotate
clockwise until the squelch "quiets".
3.5.3 Setting the Volume
With audio present, rotate the VOLUME knob clockwise for the desired
volume level.
3.5.4 Setting the Power Output
Press the MON/1/25 key for two seconds to toggle between 1 watt output
and 25 watts output. When the 1W indicator is displayed, the output power
is 1 watt. If 1W is extinguished, 25 watts is being output.
The choice of power output is dependent upon the distance of transmission
and transmitting conditions.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM8
3-9
Operation with Minimum Function Handset
3.5.5 Setting the Channel
To select the appropriate channel, rotate the CH (Channel Select) Knob
clockwise/counterclockwise or use the Channel UP/DOWN keys on the
Minimum Function Handset.
3.5.6 Selecting the Private Channel
Ten Private Channels have been allocated for specific use within certain
countries. The following table lists the Private Channel designations in
each country and the corresponding RAY215E Private Channel numbers
(1–10). On the LCD, a dash (–) appears before private channels 0 through
9. For example, channel 2 appears as –2.
PrivPriv
PrivPriv
Priv
ateate
ateate
ate
ChannelChannel
ChannelChannel
Channel
FF
FF
F
requencyrequency
requencyrequency
requency
ChannelChannel
ChannelChannel
Channel
CountryCountry
CountryCountry
Country
CH NoCH No
CH NoCH No
CH No
..
..
.
DesignatorDesignator
DesignatorDesignator
Designator
TX/RX (MHz)TX/RX (MHz)
TX/RX (MHz)TX/RX (MHz)
TX/RX (MHz)
UseUse
UseUse
Use
UK - 1 M1/37C 157.850/157.850 Pleasure Boat
- 2 M2 161.425/161.425 Pleasure Boat
Denmark - 3 L1 155.500/155.500 Pleasure Boat
- 4 L2 155.525/155.525 Pleasure Boat
Finland, - 3 L1 155.500/155.500 Pleasure Boat
Norway & - 4 L2 155.525/155.525 Pleasure Boat
Sweden - 5 L3 155.650/155.650 Pleasure Boat
Netherlands - 6 31A 157.550/162.150
Belgium - 6 31A 157.550/162.150
Denmark, - 8 F1 155.625/155.625 Fishing Boat
Finland, - 9 F2 155.775/155.775 Fishing Boat
Norway & 10 F3 155.825/155.825 Fishing Boat
Sweden
You must have the appropriate license and your RAY215E must be
programmed to use the private channel(s) that are approved for your
country.
Note: A license is required to operate the radio on the private channels.
It is your responsibility to obtain the proper license to operate the radio
on these frequencies.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM9
3-10 Operation with Minimum Function Handset
To select the Private Channel:
1. Simultaneously press and release the SCAN/MEM and MON/1/25
keys. The assigned private channel number appears in the large channel
display. If multiple Private Channels are available, the first channel
number appears. “Pc” appears in the small channel display.
2. If multiple Private Channels are available, turn the CH knob until the
desired Private Channel number appears. The displayed Private
Channel number is selected.
To exit the Private Channel, press the 16, SCAN/MEM, or MULTI keys.
Pressing 16 switches to the Priority Channel.
Pressing SCAN/MEM initiates Scan mode, which includes the Private
Channel in the list of channels being scanned.
Pressing MULTI initiates a Tri-Watch monitoring of the Private, Priority,
and Working Channels. The Private Channel appears in the large channel
display, the Working Channel appears in the small channel display, and
the MON indicator flashes.
3.5.7 Setting the Frequency Mode
The RAY215E can transmit and receive on all available International
marine VHF radiotelephone channels. With a software upgrade, the
RAY215E can also communicate on the US channel set.
If the US channel set option has been installed, pressing SCAN/MEM
and MULTI key simultaneously toggles between International and US
modes. When the International mode has been selected, the INT indicator
is illuminated. When the US mode has been selected, the INT indicator is
extinguished. There is no separate indicator for US mode.
Note: Some countries require special licensing to activate the US
channels.
3.5.8 Transmitting
Press the Push-To-Talk switch (PTT) and speak into the microphone using
a clear normal voice. If the current channel is a TX prohibited channel, an
alarm will sound when PTT is pressed indicating such a transmission is
not permitted.
If the PTT switch is pressed and held enabling the transmitter continuously
for 5 minutes, the RAY215E will automatically disable the transmitter.
Once PTT is released, the transmitter will be re-enabled.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM10
3-11
Operation with Minimum Function Handset
3.5.9 Selecting a Weather Channel
Press the MULTI key once to enter the Weather mode and use either the
Channel Select (CH) knob or Channel UP/DOWN keys on the Minimum
Function Handset to select the desired weather channel.
This function is only available when the RAY215E has been upgraded to
use the US channel set, and US mode is selected. Weather broadcasts can
only be heard in US and Canada.
3.5.10 Priority Channel
Channel 16 is programmed as the Priority Channel. To switch from the
currently-used channel to the Priority Channel at any time, press the 16
key once.
When the Priority Channel is active, a "P" appears in the small character
display.
3.5.11 Channel Memory
The RAY215E can store any International or US channel (if the optional
US channel set has been programmed). The stored channels are the ones
scanned in the Memory Scan mode.
To store a channel in memory, select the desired channel with the CH
knob and press and hold the SCAN/MEM key for 2 seconds. A tone sounds
and the MEM indicator is displayed. (Weather channels can not be stored
into memory).
To clear a channel from memory, select the memory channel and press
and hold the SCAN/MEM key for 2 seconds. The MEM indicator
extinguishes, indicating that channel is no longer stored in memory.
3.5.12 Resetting Factory Defaults
You can reset many radio settings back to their factory defaults:
• Erase any channels stored in memory for the Memory Scan function
• Erase any MMSI numbers stored for Individual Ship's Call
• Turn OFF the backlight on both the base station and full function handset
• Return to INT channels, if US mode is selected
• Return the Weather Channel to channel 0, if US mode is selected
This will NOT erase the Own Ship's MMSI ID number for your vessel
nor will it erase the PHNBOOK entries made with the Full Function
Handset.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM11
3-12 Operation with Minimum Function Handset
To perform the memory reset:
1. Turn the radio OFF.
2. Press and hold the SCAN/MEM key.
3. While continuing to hold the SCAN/MEM key, turn the radio ON.
The LCD remains blank for 2 seconds, CL appears momentarily, then
the unit switches to channel 16.
3.5.13 Scan Modes
The RAY215E is equipped with two types of scan options: All Scan and
Memory Scan. How these options are initiated depends upon whether
there are any channels stored in memory.
All Scan Mode
If no channels are stored in memory when the SCAN/MEM key is pressed,
the radio begins scanning all channels (except weather channels) as long
as no signal is received. If a signal is received, the scan stops on the
receiving channel as long as it is present. If the signal is lost for five
seconds or SCAN/MEM is pressed, the radio resumes scanning. SCAN
is displayed on the LCD while the Scan mode is active.
If the SCAN/MEM key is pressed again while SCAN is flashing, the All
Scan Standby state is suspended and the unit returns to the normal state.
To cancel the scan mode, press the SCAN/MEM key once.
Memory Scan Mode
If one or more channels are stored in memory when the SCAN/MEM key
is pressed, SCAN and MEM begin to flash simultaneously on the LCD. If
no other key is pressed within three seconds, SCAN and MEM stop
flashing and the radio begins scanning all channels currently stored in
memory. As with All Scan, if a signal is received, the scan stops on the
receiving channel until the signal is lost for five seconds or SCAN/MEM
is pressed, and then the radio resumes scanning. To cancel memory scan,
press and release SCAN/MEM.
If there are channels stored in memory but All Scan operation is desired,
press SCAN/MEM again within the 3 second period while the SCAN and
MEM indicators are flashing.
Note: Scan modes are disabled when ATIS operation is active.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM12
3-13
Operation with Minimum Function Handset
3.5.14 Monitor Mode
The RAY215E is equipped with 2 types of monitor operations: Dual Watch
and Tri-Watch.
Note: Monitor modes are disabled when ATIS operation is active.
Dual Watch Mode
Dual Watch monitors the selected working channel or Private Channel
and Channel 16. To initiate Dual Watch, first select the working or private
channel to be monitored, then press the MON/1/25 key once. The selected
working/private channel and channel 16 are monitored for traffic.
If a signal is received on the working or Priority channel, the radio monitors
that channel as long as a signal is present. Dual Watch will resume if the
signal is lost for 7 seconds. To exit the Dual Watch mode, press the 16 or
MON/1/25 keys.
Tri-Watch Mode
When the RAY215E is in International mode, Tri-Watch monitors the
selected working channel, Channel 16, and the last used Multi-channel.
To start Tri-Watch, initiate the Dual Watch mode, and then press the MULTI
key. The MULTI indicator illuminates on the LCD to indicate the Multi-
channel is also being monitored.
If the RAY215E has received an upgrade to use the US channel set, and
US mode is selected, Tri-Watch monitors the selected working channel,
Channel 16, and the last used Weather Channel for the Weather Alert
Tone. To initiate Tri-Watch, initiate the Dual Watch mode, and then press
the MULTI key. The WX indicator illuminates on the LCD to indicate the
Weather Channel is also being monitored. Operation is the same as Dual
Watch except that if a Weather Alert Tone is received, the radio
simultaneously sounds an alarm tone, WX flashes, and the NOAA Weather
Alert is monitored. NOAA weather broadcasts can only be heard in US
and Canada.
When the Private Channel is the active channel in International mode,
Tri-Watch monitors the selected Private Channel, Channel 16, and the
last used Multi-channel. To initiate Tri-Watch, press the MULTI key once.
You do not need to first enter Dual Watch mode, as you do when the
working channel is selected.
To exit the Dual Watch or Tri-Watch modes, press MON/1/25 to revert to
the last working channel or the 16 key to switch to the Priority Channel.
While in Tri-watch mode, Press MULTI to revert to Dual Watch.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM13
3-14 Operation with Minimum Function Handset
3.5.15 Multi-Call Operation
The Multi-call function stores as many channels as desired in memory for
quick access to frequently used channels.
Using Multi-Call
To start the Multi-Call operation, press the MULTI key. The last used
Multi-Call channel is displayed. Use the UP/DOWN key on the handset
or Channel Selection (CH) knob to increment/decrement through the Multi-
Call channels in memory.
When exiting Multi-Call, the last-used channel is stored to be used the
next time Multi-Call starts.
Changing from Multi-Call Channel to the Working Channel
Pressing the MULTI key toggles between the Multi-Call channel and the
last used marine working channel.
Storing a Multi-Call Channel
From the Working or Private Channel mode, select the channel to be stored.
Press and hold MULTI key for 2 seconds. The MULTI indicator appears
when the registration is complete.
Deleting a Channel from Multi-Call
From the Working or Private Channel mode, select the channel to be
deleted. Press and hold the MULTI key for 2 seconds. The MULTI indicator
disappears when the channel has been deleted.
3.5.16 LCD Backlight Function
Pressing the DIM key adjusts the brightness of LCD's backlight. Each
successive press of the DIM key switches the brightness from Off, to
Low, to Medium, to High, then back to Off.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM14
3-15
Operation with Minimum Function Handset
3.5.17 NMEA Operation
When an Optional Full Function Handset is installed enabling the Class
D DSC functionality, the RAY215E can receive valid position and time
information, which are transmitted during a DSC Distress call. This data
can be communicated via NMEA 0183 from a GPS, fishfinder, radar, or
any device that outputs GPS sentences. If the radio does not detect the
position data, it provides alerts urging you to find and correct the fault.
The optional Full Function Handset enables you to manually input this
data using the L/L ENT function, as described in Section 4.7.3.2.
Note: NMEA position data can be communicated only when an optional
Single or Dual Station Full Function Handset has been installed.
If a GPS device is not connected via NMEA, the radio emits a 5-second-
long staccato alert tone and flashes the NMEA indicator 2 minutes after
power up. This occurs every time the unit is turned on. The alarm is required
by safety regulations and cannot be disabled.
Operation at Power Up
At power up, the radio monitors the NMEA line for 1 minute. If a signal
is detected on NMEA, the radio determines whether the data is valid. If
valid, the data is accepted and the NMEA indicator is displayed on the
LCD.
If no GPS signal is detected on NMEA after the 1 minute monitoring
period, a 5-second-long staccato alert tone is emitted and the NMEA
indicator flashes. All the position fields are set to 9’s and the time and
date fields are set to 8’s.
If at a later time valid data is received on NMEA, the data is accepted and
the NMEA indicator is displayed solid (no longer flashing).
Operation When the Signal is Lost or Becomes Invalid
If positional data that was previously detected becomes invalid or is no
longer detected, the radio monitors the NMEA line for 1 minute for it to
be restored.
If a signal is restored on the NMEA line and the radio determines the data
is valid, the data is accepted and the NMEA indicator returns to a solid
state (not flashing).
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM15
3-16 Operation with Minimum Function Handset
However, if no signal is detected, the NMEA indicator flashes and a 5-
second-long staccato alert tone is emitted. The NMEA indicator continues
to flash until valid positional data is received. If valid positional data
(from the same source) is later restored, the NMEA indicator is again
displayed solid.
Operation When No Signal Detected for 4 Hours
If no valid positional data is received or input manually using the Full
Function Handset within 4 hours of the previous alert, the NMEA indicator
continues to flash and the staccato alert tone is again emitted. This pattern
is repeated every 4 hours if no positional data has been detected. If no
manual input was made during the previous 23.5 hours, all the position
fields are set to 9’s and the time and date fields are set to 8’s.
3.5.18 Digital Selective Calling (DSC)
The Digital Selective Calling (DSC) protocol is a globally applied system
used to send and receive digital Distress calls as well as Individual and
All-Ships calls on channel 70, the dedicated DSC channel for Marine
VHF. For a Distress call transmission, your RAY215E takes the position
and time information from the input NMEA data along with your Maritime
Mobile Station Identifier (MMSI) and converts it into a digital "packet".
When transmitted, this digital information lets other ships and shore
stations equipped with appropriate DSC equipment know where you are
and that you are in a Distress situation.
In the RAY215E, Class D DSC functionality is enabled by installing an
optional Full Function Handset. This can be in the form of Single Station
(Raymarine part number E46020) that replaces the Minimum Function
Handset or as a Dual Station (Raymarine part number E46022) that, when
used in conjunction with a Minimum Function Handset, enables intercom
functions between the two stations.
Note: DSC functions are enabled only when an optional Full Function
Handset has been installed. If no Full Function Handset is attached,
none of the following features will operate.
Communications in DSC mode include the following:
1. Transmitting/Receiving an Individual Call
2. Transmitting/Receiving an All Ships Call
3. Transmitting/Receiving a Distress Call (without designating type)
4. Receiving a Distress Relay Call (without designating type)
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM16
3-17
Operation with Minimum Function Handset
Individual, All Ships and Group DSC calls come in three varieties:
ROUTINE for normal calls, SAFETY for advisory alerts, and URGENCY
for assistance when life is not in immediate danger. To enable DSC mode,
press and release the DSC/PRI and D/L / I.C. keys simultaneously. The
DSC indicator illuminates and a tone sounds. Since the Distress Call
(enabled by pressing and holding the Distress Key for 5 consecutive
seconds) automatically selects the DSC mode, it is not necessary to press
the DSC/PRI and D/L / I.C. to make a distress call.
When a DSC call is received, the radio automatically enters DSC mode if
you are currently on a selected working channel or private channel, in the
Monitor mode, or in the Scan mode.
Note: You must program the ship's MMSI number before the radio can
enter the DSC mode. See section 3.5.18.1 below.
3.5.18.1 MMSI Number Setup on Base Station
You must enter your Maritime Mobile Service Identity (MMSI) number
in the RAY215E before the DSC system will be operational. You can
request an MMSI number when you apply for a radio license, if your
country allows you to enter an MMSI number yourself. Otherwise, your
authorized distributor or dealer can program the MMSI for you.
Note: Because it is required for enabling DSC functionality, a Second
Station Full Function Handset must be installed before you can program
in the MMSI number on the base station.
Once you have received your MMSI number, enter it into the radio as
follows:
1. Press and hold the DSC/PRI and D/L I.C. keys simultaneously for 2
seconds. A tone sounds and two dashes (- -) appear in the large character
display.
2. Press and release SCAN/MEM key. The DSC indicator appears, "0"
is displayed in the large character display, and "1" is displayed in the
small character display.
Note: If an MMSI number is already in memory, the MMSI entry scrolls
across the display, one digit at a time.
3. Rotate the Channel Select (CH) knob until the first digit of your MMSI
number appears in the large character display. (Channel UP/DOWN
keys on the Minimum Function Handset are disabled during this
process).
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM17
3-18 Operation with Minimum Function Handset
4. Press the DSC/PRI key once to accept. The small character display
now shows a "2", designating the second digit in your MMSI number.
5. Rotate the Channel Select (CH) knob until the second digit of your
MMSI number appears in the large channel display.
6. Press the DSC/PRI key once to accept.
7. Enter all 9 digits of the MMSI number in the same way.
Once the 9th digit has been entered and accepted, the RAY215E plays
back the 9 digits (one digit at a time) to verify proper entry.
Note: Ensure the MMSI number entered is correct with this verification
playback. Once the number is accepted as outlined in the next step, it
cannot be changed except by Raymarine factory representatives.
8. If the number is verified as correct, press and hold the DSC/PRI key
for 2 seconds and a tone sounds. Your MMSI number has now been
stored in memory.
If the number is incorrect, press the DSC/PRI key once and release.
The radio will revert to the beginning of the entry process to start over
again. This step can be repeated as many times as required until the
number is entered correctly.
ROTATE
CH
PRESS & REL
DSC
PRESS & REL
DSC
PRESS & HOLD
DSC
MMSI digit
digit position
Select desired digit
Next digit position
Select desired digit
Continue thru last digit position
Radio replays all digits...
MMSI number accepted
PRESS & REL
DSC
Returns to working channel
...through the 9th position
Returns to first digit position
ROTATE
CH
Select desired digit
ROTATE
CH
PRESS & REL
DSC
PRESS & HOLD
DSC + D/L
PRESS & REL
SCAN
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM18
3-19
Operation with Minimum Function Handset
3.5.18.2 Individual Ship's Call
An Individual Ship's Call is a DSC call made to a specific ship identified
by its MMSI number. There are three types: ROUTINE for normal calls,
SAFETY for advisory alerts, and URGENCY for assistance when life is
not in immediate danger.
The RAY215E can receive all three types of Individual calls but can only
transmit ROUTINE Individual calls. As with any DSC operation, the call
is made on channel 70.
Sending an Individual Ship's Call
The RAY215E can only send a Routine Individual Call. The MMSI
number of the ship to which the Individual Call is to be sent can be input
manually or selected from a phonebook listing in memory. This section
includes instructions for using both methods and for adding numbers to
the phonebook.
Tip: You should first select the desired working channel before entering
the DSC mode to send an Individual Ship’s Call. That way, that channel
will already be displayed when the radio prompts for a working channel
after the MMSI has been selected.
Note: Only simplex channels (those which are transmitted and received
on the same frequencies) can be selected as the Individual Call working
channel. See the frequency list in Section 6 to see which channels are
simplex.
Using a manually input MMSI number
1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to
place the unit in DSC mode. "70" appears in the large channel display,
the DSC indicator illuminates, and "in" appears in the small channel
display to designate individual call.
2. Press and release the DSC/PRI key. The DSC indicator appears, "0" is
displayed in the large character display, and "1" is displayed in the
small character display.
3. Rotate the Channel Select (CH) knob until the first digit of the other
ship’s MMSI number appears in the large character display. (Channel
UP/DOWN keys on the microphone are disabled during this process).
4. Press the DSC/PRI key once to accept. The small character display
now shows a "2", designating the second digit in other ship’s MMSI
number.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM19
3-20 Operation with Minimum Function Handset
5. Rotate the Channel Select (CH) knob until the second digit of other
ship’s MMSI number appears in the large channel display.
6. Press the DSC/PRI key once to accept.
7. Enter all 9 digits of the MMSI number in the same way.
8. Once the 9th digit has been entered and accepted, the RAY215E plays
back the 9 digits to verify the entry.
If the number is incorrect, press the DSC/PRI key once and release.
The radio will revert to the beginning of the entry process to start over
again. This step can be repeated as many times as required until the
number is entered correctly.
9. When the MMSI number is verified as correct, press and hold the
DSC/PRI key for 2 seconds to verify.
Note: The operation is cancelled if the 16 key is pressed or if no keys
are pressed for 60 seconds during any part of this process.
PRESS & REL
DSC + D/L
PRESS & REL
DSC
ROTATE
CH
PRESS & REL
DSC
PRESS & REL
DSC
PRESS & HOLD
DSC
MMSI digit
digit position
Select desired digit
Next digit position
Select desired digit
Continue thru last digit position
Radio enters DSC mode
Radio replays all digits...
MMSI number accepted
PRESS & RELEASE
DSC
Process starts over
...through the 9th position
ROTATE
CH
Select desired digit
ROTATE
CH
PRESS & RELEASE
DSC
Radio replays all digits through the 9th position
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM20
3-21
Operation with Minimum Function Handset
10.After you have selected the other ship's MMSI number, the radio
prompts you for the working channel you wish to communicate on.
The large character display shows the last used channel number and a
"W" appears in the small channel display. Use the Channel Select
(CH) knob to select the desired working channel for the Individual
Call.
11. Press the DSC/PRI key once. The TX indicator on the LCD flashes,
indicating the RAY215E is ready to transmit.
12.Press the PTT switch to send the digital "packet" of information. The
radio waits for an acknowledgment from the targeted ship or station.
13. If the target station acknowledges, a tone sounds and "ACK" illuminates
on the LCD. After 2 seconds, the RAY215E switches to the previously
selected working channel.
or
If the call is not acknowledged, exit the DSC mode by pressing the 16
key.
PRESS & HOLD
DSC
ROTATE
CH
[TX] Flashing
PRESS & REL
DSC
Returns to last used channel
"ACK" signal received
from the specified ship
Standby for "ACK"
from specified ship
2 seconds after receiving ACK,
switches to selected channel
PRESS
PTT
Select desired working channel
Using an MMSI number selected from the phonebook:
Using the RAY215E with a Minimum Function Handset, you can select
from up to ten other ship's MMSI numbers that have been stored in the
phonebook. The numbers are identified by a single letter that you have
assigned to it. You must note what letter you assigned to the MMSI number
because only that letter appears on the LCD when you are retrieving it.
Note: The operation is cancelled if the 16 key is pressed or if no keys are
pressed for 60 seconds during any part of this process.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM21
3-22 Operation with Minimum Function Handset
1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to
place the unit in DSC mode. "70" appears in the large channel display,
the DSC indicator illuminates, and "in" appears in the small channel
display to designate Individual Call.
2. Press and release the SCAN/MEM key. A letter appears in the small
channel display, which is associated with one of the other ship's MMSI
numbers in the phonebook.
3. If you wish to use the use the other ship's MMSI number associated
with this letter, press DSC/PRI.
4. To use a different letter, rotate the Channel Selection Knob until the
desired letter is displayed. Press DSC/PRI to select this letter.
5. After you have selected the other ship's MMSI number, the radio
prompts you for the working channel to communicate on. The large
character display shows the last used channel number and a "W"
appears in the small channel display.
6. Using the Channel Select (CH) knob on the front panel, select the
desired channel, and press the DSC/PRI key once. The TX indicator
on the LCD flashes, indicating the RAY215E is ready to transmit.
7. Press the PTT switch to send the Individual Ship's Call. After the digital
"packet" of information is sent, the radio waits for an acknowledgment
from the targeted ship or station.
8. If the target station acknowledges, a tone sounds and "ACK"
illuminates on the LCD. After 2 seconds, the RAY215E switches to
the previously selected working channel.
or
If the call is not acknowledged, exit the DSC mode by pressing 16
key.
Note: The operation is cancelled if the 16 key is pressed or if no keys
are pressed for 60 seconds during any part of this process.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM22
3-23
Operation with Minimum Function Handset
PRESS & REL
DSC + D/L
PRESS & REL
SCAN
Radio enters DSC mode
ROTATE
CH
PRESS & REL
DSC
ROTATE
CH
[TX] Flashing
PRESS
DSC
Select working channel
ACK received from specified ship
Standby for ACK from specified ship
2 seconds after receiving ACK,
switches to selected channel
PRESS
PTT
Select letter assigned to desired MMSI
Returns to last used channel
To store an MMSI number in phonebook:
1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to
place the unit in DSC mode. "70" appears in the large channel display,
the DSC indicator illuminates, and "in" appears in the small channel
display to designate individual call.
2. Press and release the DSC/PRI key. The DSC indicator appears, "0" is
displayed in the large character display, and "1" is displayed in the
small character display.
3. Rotate the Channel Select (CH) knob until the first digit of your MMSI
number appears in the large character display. (Channel UP/DOWN
keys on the microphone are disabled during this process).
4. Press the DSC/PRI key once to accept. The small character display
now shows a "2", designating the second digit in your MMSI number.
5. Rotate the Channel Select (CH) knob until the second digit of your
MMSI number appears in the large channel display.
6. Press the DSC/PRI key once to accept.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM23
3-24 Operation with Minimum Function Handset
7. Enter all 9 digits of the MMSI number in the same way.
Note: The operation is cancelled if the 16 key is pressed or if no keys
are pressed for 60 seconds during any part of this process.
8. Once the 9th digit has been entered and accepted, the RAY215E plays
back the 9 digits just entered for proper entry verification.
If the number is incorrect, press the DSC/PRI key once and release.
The radio will revert to the beginning of the entry process to start over
again. This step can be repeated as many times as required until the
number is entered correctly.
9. When the MMSI number is verified as correct, press the SCAN/MEM
key. A letter appears in the small channel display.
10.If you wish to assign this letter to the Other Ship's MMSI, press DSC/
PRI.
11. If you wish to assign a different letter to the Other Ship's MMSI, rotate
the Channel Selection Knob until the desired letter is displayed.
12.Press DSC/PRI to store the MMSI number/letter assignment into the
phonebook.
Up to ten Other Ship's numbers can be stored in the phonebook. The
letters available are as follows:
You must note what letter you assigned to the MMSI number because
only that letter appears on the LCD when you are retrieving it.
Note: No data is stored in memory when a wrong key operation or an
interruption of power occurs during the entry procedure.
The operation is cancelled if the 16 key is pressed or if no keys are
pressed for 60 seconds during any part of this process.
To delete an MMSI number from the phonebook:
1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously.
2. Press and release the SCAN/MEM key.
3. Rotate the Channel Selection Knob until the letter representing the
MMSI number to be deleted is displayed.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM24
3-25
Operation with Minimum Function Handset
4. Press and hold D/L/I.C. The selected number is deleted from the
phonebook and the radio switches to channel 16.
Receiving an Individual Ship's Call
When an Individual Ship's Call is received, the radio automatically enters
DSC mode if you are currently on a selected working channel or private
channel, in the Monitor mode, or in the Scan mode.
When receiving Individual Ship's Call
1. If your station is targeted for an Individual Ship's Call, a tone sounds
and the unit automatically switches to DSC mode. TX flashes on the
LCD and one of the following categories of Individual Ship's Calls
flashes in the small number display:
"Ir" for ROUTINE Individual Ship's Call
"IS" for SAFETY Individual Ship's Call
"IU" for URGENCY Individual Ship's Call
2. To acknowledge the incoming Individual Ship's Call, press the PTT
key. The acknowledge is transmitted and your RAY215E automatically
selects the working channel specified by the originating ship or station.
3. If you do not wish to acknowledge the call, press the 16 key to exit the
DSC mode.
PRESS & RELEASE
16
PRESS & RELEASE
PTT
Receive Individual Ship's Call:
Routine, Safety, or Urgency
Acknowleging the call
Not acknowleging the call
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM25
3-26 Operation with Minimum Function Handset
3.5.18.3 All Ships Call
The All Ships Call is used to send out a message to all ships in range that
you need assistance but the situation is not serious enough for a Distress
Call. This call should only be used if hailing for assistance on channel 16
fails. There are three types of All Ships Calls: ROUTINE for normal calls,
SAFETY for advisory alerts, and URGENCY for assistance when life is
not in immediate danger. The RAY215E can receive all three types of
these calls but can transmit only SAFETY and URGENCY. As with any
DSC operation, the call is made on channel 70. Then, after the All Ships
Call is sent or received, the radio automatically selects channel 16.
Sending an All Ships Call
1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to
enter the DSC mode.
2. Rotate the Channel Select (CH) knob on the front panel to select the
desired type of call. The following appears in the small channel display:
"AS" for SAFETY All Ships Call
"AU" for URGENCY All Ships Call
3. Press and release the DSC/PRI key and TX begins to flash.
4. Press the PTT switch to transmit the All Ships Call. The radio switches
to Channel 16.
5. Any station responding to your call converses on Channel 16.
ROTATE
CH
PRESS & REL
PTT
PRESS & REL
DSC + D/L
PRESS & REL
DSC
ROTATE
CH
Receiving an All Ships Call
If you are currently on a selected working channel or private channel, in
the Monitor mode, or in the Scan mode, the radio automatically enters
DSC mode when an All Ships Call is received. The type of call is displayed
in the small channel display and an alarm is sounded.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM26
3-27
Operation with Minimum Function Handset
Press the DSC/PRI key once and the radio automatically selects channel
16. There is no acknowledge required for an All-Ship's Call. If you do not
wish to accept the call, press the 16 key to exit the DSC mode.
PRESS & RELEASE
DSC
Receive All Ships Call:
Routine, Safety, or Urgency
Converse on channel 16
3.5.18.4 Group Call
The Group Call feature sends transmissions that are only received by
radios that share a common Group MMSI number.
The RAY215E requires a Full Function Handset to program in the Group
MMSI number. For this reason, the Minimum Function Handset can only
receive Group Calls. You must use the Full Function Handset to send a
Group Call.
If you are currently on a selected working channel or private channel, in
the Monitor mode, or in the Scan mode when a Group Call is received,
the radio automatically enters DSC mode, sounds an alarm, and displays
the type of call.
After receiving a Group Call, press and release the DSC key to accept the
call. The unit switches to the working channel and extinguishes the DSC
indicator, indicating the unit has exited the DSC mode.
The large channel display indicates the working channel and the small
channel display is extinguished. If you do not wish to acknowledge the
call, press the 16 key to exit the DSC mode.
PRESS & RELEASE
DSC
Receive Group Call
Call accepted. Converse on
selected Working Channel.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM27
3-28 Operation with Minimum Function Handset
3.5.18.5 Distress Call
A Distress Call allows you to send out a digital "packet" of data at high
power that includes your position, time, and MMSI number. All ships and
stations outfitted with the correct type of DSC equipment will be able to
pinpoint your position and either relay the information or respond directly.
Using the Distress key overrides all other functions.
Note: DSC functions are enabled only when an optional Full Function
Handset has been installed. If no Second Station Full Function Handset
is attached, the Distress button on the Minimum Function Handset will
not operate.
Sending a Distress Call
1. On the back of the microphone, lift the door marked DISTRESS.
2. Press and hold the red Distress key for 5 seconds. After 1 second, the
LCD displays a countdown from four to zero, beeping every second.
3. When the countdown has completed, the radio enters the DSC mode
and sends the digital information at high power. Once transmitted, the
radio monitors channel 70 for a Distress acknowledge but also monitors
channel 16 for emergency traffic.
Note: When a Distress Call is sent, the unit emits a VERY LOUD distress
alarm tone. To mute the alarm without interrupting the Distress Call,
press the DSC/PRI key on the RAY215E base station. The radio will remain
in DSC mode.
4. The Distress Call is automatically re-transmitted every 3.5 to 4 minutes
as long as you remain in the DSC mode. The radio continues to transmit
until either an acknowledge is received or the DSC mode is manually
exited by pressing the 16 key.
5. If a receiving station has Distress acknowledge capability and sends
an acknowledge to you, the LCD will sound the DSC tone, display
"ACK", and exit the DSC mode where channel 16 is automatically
selected.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM28
3-29
Operation with Minimum Function Handset
PRESS & HOLD
DISTRESS
Acknowledge signal received
Switch to Channel 16
PRESS & HOLD
DISTRESS
After 1 sec, countdown begins
Distress call transmitted
Hold DISTRESS for full 5 seconds
Receiving a Distress Call
When a DSC Distress call is received, the radio automatically enters DSC
mode if you are currently on a selected working channel or private channel,
in the Monitor mode, or in the Scan mode. You will not receive a DSC
call if the radio is transmitting or receiving a non-DSC call.
1. When receiving a calling signal, the unit sounds the DSC tone and
enters the DSC mode. A "d" flashes in the small channel display for
Distress.
2. Press the DSC/PRI key. The radio accepts the call, silences the alarm,
and switches to channel 16.
Note: When a Distress Call is received, the unit emits a VERY LOUD
distress alarm tone. Pressing the DSC/PRI key mutes this alarm.
3. The RAY215E cannot acknowledge or relay a DSC Distress Call, so
after the Distress Call is received, attempt to contact the vessel in
distress on channel 16 and render assistance.
Switch to Channel 16
PRESS & RELEASE
DSC
Distress Call received
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM29
3-30 Operation with Minimum Function Handset
3.5.18.6 Distress Relay Call
Sometimes a ship’s distress call can be relayed from another ship or a
shore station. The RAY215E can only receive a Relayed Distress call that
has been addressed to All Ships.
If the radio is active on a working channel or private channel, in the Monitor
mode or in the Scan mode when a Distress Relay Call is received, the unit
automatically enters DSC mode and emits an alert tone. The DSC indicator
illuminates, 70 is indicated on the large channel display, and "dr" flashes
on the small channel display.
Press and release DSC/PRI. The unit switches to channel 16. "16" appears
as the working channel on the large channel display while the small channel
display is extinguished. The DSC indicator is also extinguished, indicating
the unit has exited the DSC mode.
The alert tone continues to sound until DSC/PRI is pressed to accept the
call or 16 key is pressed to exit the DSC mode.
Switch to Channel 16
PRESS & RELEASE
DSC
Distress Relay Call received
3.5.19 ATIS ID No. Entry
The Automatic Transmission Identification System (ATIS) is used in some
European countries to identify vessels in their inland waterways. After
the PTT key is released following a transmission, the vessel’s ATIS ID
number is also transmitted.
You must enter your ATIS ID number into the RAY215E before the ATIS
system will be operational. You can request an ATIS number when you
apply for a radio license.
Regulations in some regions may not allow end users to program their
own ATIS number. If this unit was purchased to be used in such a region,
this function will be disabled and the programming must be done by your
Raymarine distributor.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM30
3-31
Operation with Minimum Function Handset
Notes:
1. After the ATIS ID number has been programmed, the ATIS function
will be active all the time. You cannot disable it unless you have a Full
Function Handset installed.
2. While ATIS is active (the ATIS indicator is illuminated), the Scan and
Monitor functions are disabled. Also, certain channels are limited to
1 watt output power.
3. This is a one time operation. Once the ATIS number has been
programmed, you will not be able to change it without returning it to
your dealer/distributor for reprogramming.
After you have received your ATIS number, enter it into the radio as
follows:
1. Press and hold the DSC/PRI and D/L I.C. keys simultaneously for 2
seconds. A tone sounds and two dashes (- -) appear in the large character
display.
2. Press and release MON/1/25 key. The ATIS indicator appears, "0" is
displayed in the large character display, and "1" is displayed in the
small character display.
Note: If an ATIS ID number is already in memory, the ATIS entry
scrolls across the display, one digit at a time.
3. Rotate the Channel Select (CH) knob until first digit of your ATIS ID
number appears in the large character display. (Channel UP/DOWN
keys on the microphone are disabled during this process).
4. Press the DSC/PRI key once to accept. The small character display
now shows a “2”, designating the second digit in your ATIS ID number.
5. Rotate the Channel Select (CH) knob until the second digit of your
ATIS ID number appears in the large channel display.
6. Press the DSC/PRI key once to accept.
7. Enter all 9 digit of the ATIS ID number in the same way.
Once the 9th digit has been entered and accepted, the RAY215E will
playback the 9 digits (one digit at a time) to verify the entry.
Note: Ensure the ATIS ID number entered is correct with the
verification playback. Once the number is accepted as outlined in the
next step, it can not be changed except by Raymarine representatives.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM31
3-32 Operation with Minimum Function Handset
ROTATE
CH
PRESS & REL
DSC
PRESS & REL
DSC
PRESS & HOLD
DSC
ATIS digit
digit position
Select desired digit
Next digit position
Select desired digit
Continue thru last digit position
Radio replays all digits...
ATIS number accepted
PRESS & REL
DSC
Returns to working channel
...through the 9th position
Returns to first digit position
ROTATE
CH
Select desired digit
ROTATE
CH
PRESS & REL
DSC
PRESS & HOLD
DSC + D/L
PRESS & REL
MON
to select
to accept
8. If the number is verified as correct, press and hold the DSC key for 2
seconds and a tone sounds. Your ATIS ID number has now been stored
in memory.
9. If the number is incorrect, press the DSC key once and release. The
radio will revert to the beginning of the entry precess start over again.
This step can be repeated as many times as required until the number
is entered correctly.
After the ATIS ID number has been programmed, the ATIS function will
be active all the time, unless you have a full function handset installed. If
a full function handset is installed, you can toggle the ATIS operation on
and off by pressing the SCAN and D/L/I.C keys simultaneously.
RAY215_EURO Sect3.p65 2/14/2002, 4:01 PM32
4-1
Operation with Full Function Handset
Section 4 Operation with Full
Function Handset
4.1 Introduction
The RAY215E can be operated with the standard Minimum Function
Handset, or an optional Full Function Handset that enables additional
features, or both handsets to enable intercom capabilities. This section
describes using the RAY215E with the optional Full Function Handset.
See section 3 for operation using the standard Minimum Function Handset.
The Full Function Handset enables Class D DSC operations and NMEA
(GPS) position data transmissions in the RAY215E. DSC functions
include: Individual, Group, All Ships, and Distress calls. To have DSC
and NMEA (GPS) position functionality available on the RAY215E,
you must have a Full Function Handset installed.
The Full Function Handset also provides you with these additional features:
• Full alphanumeric keypad
• Dedicated keys for Individual and All Ships DSC calls
• DSC distress calls that describe the type of distress
• Send and receive DSC Group Calls
• Expanded ship and shore phonebooks for making DSC Individual calls
• Manually enter lat/lon and UTC time when GPS input is not available
The Full Function Handset option is available as a Single Station
(Raymarine part number E46020) that replaces the Minimum Function
Handset or as a Second Station (Raymarine part number E46022) that,
when used in conjunction with a Minimum Function Handset, enables
intercom functions between the two stations.
4.2 Minimum / Full Function Handset Priority
When both a Minimum Function Handset and Full Function Handset are
in use, only one can have priority to make a call. When the Full Function
Handset is out of its cradle, it has priority over the Minimum Function
Handset and the REMOTE indicator illuminates on the LCD of the base
station. When the Full Function Handset is in the cradle, the Minimum
Function Handset has priority and the REMOTE indicator extinguishes.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM1
4-2 Operation with Full Function Handset
In an emergency, the fist microphone / base station can override the full
function handset to make a call even though the handset has priority (is
off the cradle). To override the handset, press and hold the DSC/PRI key
on the base station. The REMOTE indicator flashes and the base station
regains priority control. Make your call as usual using the fist microphone.
On the full function handset, OVERRIDE appears on the dot matrix
display. In this mode, all keys are disabled on the handset except for
DISTRESS. The base station retains control until the DSC/PRI key is
again pressed and held.
Note: The RAY215E is designed to have the base station as the priority
unit. You should install the base station in the radio operation room or
the location from which the ship is normally navigated. If a Second Station
Full Function Handset is also installed, that handset is the one that should
be installed in the remote location.
4.3 Handset Connections
The Full Function Handset connects to the port labeled HANDSET/
RELOCATION KIT on the rear of the base station (Figure 4-2). The Full
Function Handset will not operate if connected to the port on the front of
the base station.
If both a Minimum Function Handset and Second Station Full Function
Handset are to be used, the Minimum Function Handset must be connected
to the front port with the Full Function Handset connected to the
HANDSET/RELOCATION KIT port on the rear. Once installed, the two
stations can communicate with one another using the Intercom function
described in section 4.6.14.
Figure 4-1 Rear Connections
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM2
4-3
Operation with Full Function Handset
4.4 Controls and LCD Display
Figure 4-2 Layout of Controls
4.4.1 Controls
This section describes the control buttons and display messages that appear
on the Full Function Handset.
Note: This Full Function Handset is also used with Raymarine radios
that have additional features. As a result, the yellow Function labels
POWER (16 key), CELL (3 key), HAIL (* key), and FOG (# key) represent
features that are not available on the RAY215E.
INDV key
Switches to the DSC Individual Ship’s Call mode for initiating
selective calls (ship-to-ship, group calls, etc.) using a specific MMSI
number. Descriptions of these operations follow.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM3
4-4 Operation with Full Function Handset
Note: An MMSI number is required to operate the DSC equipment
in this radio. You can program the MMSI number yourself one time
only using the Menu Operation described in Section 4.7.4.2 or you
can have your Raymarine dealer program the number for you.
ALL SHIP key
Switches to the All Ships Call mode for Safety and Urgency
transmissions. Descriptions of subsequent operations appear below
in Section 4.6.18.6 Transmitting All Ships Call.
!
VOL UP/DOWN key
Changes the sound volume of the handset. Pressing the UP
∧∧
∧∧
∧
key
increases the volume, while the DOWN
∨∨
∨∨
∨
key causes it to decrease.
The number of segments in the VOL bar graph on the LCD display
will increase or decrease accordingly. This setting does NOT affect
the volume of the base station or external speaker.
"
SQ UP/DOWN (SCROLL) key
Increases or decreases the squelch sensitivity. Pressing the UP
∧∧
∧∧
∧
key increases the squelch, while the DOWN
∨∨
∨∨
∨
key decreases it. The
number of segments in the SQ bar graph on the LCD display will
increase or decrease accordingly. This key is also used as a scroll
key for selecting menu items and other settings, as described below.
#
16 key
Switches between the Working or Private Channel and Channel 16
(the Priority Channel).
Note: The POWER label over this key does not pertain to the
RAY215E.
$
MON/TRI key
Starts the Dual-Watch monitor mode. Pressing the FUNC key
followed by the MON/TRI key initiates the Tri-Watch monitor mode.
%
1/MEM key
This key inputs the number 1. When an alphanumeric response is
appropriate, this key alternates between entering a 1 and a space. If
the channel number indicated on the LCD display is not currently
stored in memory, pressing the FUNC key followed by the 1/MEM
key enters that channel number into memory. If the currently indicated
channel has already been stored, pressing the FUNC key followed
by the 1/MEM key deletes that channel from memory.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM4
4-5
Operation with Full Function Handset
&
2/SCAN key
This key inputs the number 2. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
2, A, B, then C. Pressing the FUNC key followed by the 2/SCAN
key toggles Scan mode ON or OFF. Scan mode is described below
in Section 4.6.15.
'
3 key
This key inputs the number 3. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
3, D, E, then F.
Note: The CELL label over this key does not pertain to the RAY215E.
4/US key
This key inputs the number 4. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
4, G, H, then I. Pressing the FUNC key followed by the 4/US key
alternates the frequency groups between US and International mode
if US channels are enabled in your radio. If US channels are not
enabled, attempting to access this secondary function will result in
an alarm tone.
5/PRIV key
This key inputs the number 5. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
5, J, K, then L. Pressing the FUNC key followed by the 5/PRIV key
switches to the Private Channel mode if Private Channels are enabled
in your radio. If Private Channels are not enabled, attempting to access
this secondary function will result in an alarm tone.
6/WX key
This key inputs the number 6. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
6, M, N, then O. Pressing the FUNC key followed by the 6/WX key
alternates between the Working Channel and the Weather Channel.
This operation is valid only in US frequency mode.
!
7/ D/L key
This key inputs the number 7. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
7, P, Q, R, then S. Pressing the FUNC key followed by 7/ D/L toggles
between full receiver sensitivity (distant mode) and attenuated
receiver sensitivity (local mode). Local mode is used in high traffic
areas to decrease unwanted reception. While in local mode (receiver
is desensitized), the DESENS indicator appears in the LCD display.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM5
4-6 Operation with Full Function Handset
"
8/M-CALL key
This key inputs the number 8. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
8, T, U, then V. Pressing the FUNC key followed by the 8/M-CALL
key starts Multi-Call mode. If the key is pressed during Multi-Call
mode, the operation returns to normal mode.
#
9/ 1/25 key
This key inputs the number 9. When an alphanumeric response is
appropriate, each press of this key alternately inputs the characters
9, W, X, Y, and then Z. Pressing the FUNC key followed by the 9/ 1/
25 key alternates the transmission power between 1W and 25W.
$
* key
This key inputs an asterisk (*).
Note: The HAIL label over this key does not pertain to the RAY215E.
%
0/IC key
This key inputs the number 0. Pressing the FUNC key followed by
the 0/IC key starts Intercom mode, which enables conversation
between the Minimum Function Handset connected to the port on
the front of the base station and a full function handset connected to
the port on the rear of the base station. Pressing the FUNC key
followed by this key during Intercom mode returns operation to
normal mode.
&
# key
This key inputs the # character.
Note: The FOG label over this key does not pertain to the RAY215E.
'
ENT key
This key performs the Enter function. It is used to confirm and
implement an input action. Pressing the FUNC key followed by the
ENT/MENU key initiates the Menu mode.
CLR key
Depending on when it is used, this key exits the current mode and
reverts to the last used mode or normal operation. This key also can
be used to clear any alphanumeric inputs one at a time in the order
that they were entered. Pressing the FUNC key followed by CLR/
LOG key initiates the Digital Selective Calling (DSC) Log. Pressing
the key during logging returns operation to normal mode.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM6
4-7
Operation with Full Function Handset
FUNC key
Initiates the Function mode and activates the FUNC indicator in the
LCD display. The next key pressed determines the function selected.
(See above key descriptions.) Pressing this key twice starts Dimmer
mode, which reduces the brightness of LCD's backlight.
Channel UP/ DOWN switch
Pressing this switch during normal operation changes the channel
number UP or DOWN.
!
PTT (Press-to-Talk) switch
Pressing this switch during normal operation places the radio in
Transmit mode and displays the TX indicator in the LCD. When the
switch is pressed in various function modes, the assigned operation
is initiated.
Note: After 5 minutes of continuously holding the PTT switch, the
radio will automatically stop transmitting. To begin transmitting
again, release the PTT and depress again.
"
DISTRESS switch
This switch is located under the small door labeled DISTRESS on
the back of the handset. Pressing and holding this switch for 5 seconds
selects Distress Signal Call mode. Subsequent operations are
described in section 4.6.18.8.
4.4.2 LCD Display
The following describes the functional characters on the RAY215E
Handset's LCD.
Figure 4-3 LCD Display Layout
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM7
4-8 Operation with Full Function Handset
NMEA indicator
Displayed when the radio receives valid NMEA position data. If the
data is invalid or no data is received for a period of time, the indicator
disappears.
FUNC indicator
Displayed when the FUNC key is pressed. Disappears when another
key is pressed, or after no other key is pressed for a period of time.
!
WX indicator
Displayed while in Weather Channel mode (optional US frequency
set only).
"
TX indicator
Displayed while transmitting.
#
US indicator
Displayed when the optional US frequency group is selected.
$
INT indicator
Displayed when the International frequency group is selected.
%
1W indicator
Displayed when the transmission power of 1W is selected with the
9/1/25 key or when a low power channel is selected.
&
DESENS indicator
Displayed during the desensitized receiving (local) mode.
'
MEM indicator
Displayed while the channel stored in memory is displayed. This
indicator flashes before the start of the memory scan operation.
MULTI indicator
Displayed while the channel stored in Multi-Call memory is displayed.
SCAN indicator
Displayed during Scan mode. If channels have been stored in memory,
this indicator will be flashing before the start of Scan mode.
DSC indicator
Displayed when in a Digital Selective Calling (DSC) call mode, DSC
log, or the DSC menu.
!
ATIS indicator
Displayed when the ATIS (automatic identification transmission)
feature is enabled.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM8
4-9
Operation with Full Function Handset
"
VOL indicator (in bar graph)
Represents the current sound volume level of the handset. A louder
volume displays a larger number of segments in the bar graph. This
bar graph is not displayed during Menu mode.
#
SQL indicator (in bar graph)
Represents the current squelch level. A deeper squelch displays a
larger number of segments in the bar graph.
$
Three-digit, Seven-segment indicators
Display the channel number or state of the radio.
%
Nine-digit Dot-matrix display
Displays alphanumeric messages, modes, and functional status of
the radio.
4.5 Radio Functions
1. Selecting the Frequency Mode
Channel selection is available from among two frequency groups:
International and US (available only with a software upgrade).
2. Receiving the Weather Channels (Optional)
The RAY215E is programmed to receive 10 NOAA weather channels
and will sound an alarm if a Weather Alert is received. This operation
is available only in US frequency mode, if this option has been
activated in your unit. NOAA weather broadcasts can only be heard
in US and Canada.
3. Private Channel Operation
If this feature is enabled in your radio, you can use the Private
Channels that have been allocated for specific use within certain
countries.
4. Dimmer Operation
Select from four LCD backlight levels, including OFF.
5. Monitor Operation
Select from Dual-Watch or Tri-Watch mode.
6. Scan Operation
Select from All Scan or Memory Scan.
7. Selecting Transmission Power Output
Select either 1W or 25W for the transmission power.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM9
4-10 Operation with Full Function Handset
8. Digital Selective Calling (DSC) Operation
These functions include Individual Ships Call, All Ships Call, Distress
Call, Group Call, and DSC logging capability.
Note: An MMSI number is required to operate the DSC equipment
in this radio. You can program the MMSI number yourself one time
only, if permitted in your region, using the Menu Operation described
in Section 4.7.4.2 or you can have your Raymarine dealer program
the number for you.
9. NMEA Positional Data Reception
Positional information from external equipment is obtained using
the NMEA 0183 interface.
10. Remote Operation
When both a Minimum Function Handset and Full Function Handset
are connected, the RAY215E can be controlled by either handset.
When the Full Function Handset is out of its cradle, it has priority
over the Minimum Function Handset. When the Full Function
Handset is in the cradle, the Minimum Function Handset has priority
and BASE appears on the handset’s LCD.
If you need to make an emergency call with the Minimum Function
Handset while the Full Function Handset is out of the cradle, press
and hold the DSC/PRI key. The Minimum Function Handset regains
priority control and OVERRIDE appears on the Full Function
Handset’s LCD.
11. Intercom Function between Handsets
Intercom mode enables conversation between a Minimum Function
Handset connected to the front of the base station and a Full Function
Handset connected to the to the rear of the base station.
12. Reduced Receiving Sensitivity (Local Mode)
This function decreases receiver sensitivity in high traffic areas to
decrease unwanted reception.
4.6 Operating Procedures
With the Full Function Handset, all operations can be made on the Handset
except turning ON/OFF the base station and adjusting the sound volume
of the External Speaker.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM10
4-11
Operation with Full Function Handset
4.6.1 Setting the Volume
The sound volume adjustment for the handset has 11 settings. Pressing
and releasing the VOL UP
∧∧
∧∧
∧
key increases the volume by one level;
pressing and releasing the VOL DOWN
∨∨
∨∨
∨
key reduces the volume by
one level.
The number of segments in the VOL bar graph on the LCD display will
increase or decrease accordingly. If the VOL UP/DOWN keys are pressed
and held, the volume levels will automatically change every half-second.
Setting the Volume on the External Speaker (Second Stations only)
The volume knob on the External Speaker controls its sound volume. Turning
the knob clockwise increases the volume; turning it counterclockwise reduces
the volume. Turning the knob fully counterclockwise until you hear a “click”
switches off the speaker completely.
General alert tones will be sounded on the external speaker as long as it is
switched on. Received Distress or Urgency calls as well as the Weather
Alert Alarm will sound at maximum volume regardless of whether the
external speaker is switched on or off
Note: The external speaker is included with the Second Station Full
Function Handset kit but not the Single Station kit.
4.6.2 Setting the Squelch
The squelch adjustment enables you to "quiet" the receiver when no signal
is being received. The squelch adjustment for the handset has 11 settings.
Pressing and releasing the SQ UP
∧∧
∧∧
∧
key increases the squelch by one
level; pressing and releasing the SQ DOWN
∨∨
∨∨
∨
key decreases it by one
level. The number of segments in the SQ bar graph on the LCD display
will increase or decrease accordingly. If the SQ UP/DOWN keys are
pressed and held, the squelch levels will automatically change every half-
second.
4.6.3 Using the Function Key
Most of the keys on the handset control secondary operations, indicated
by the label (in gold) above them. To initiate the operation marked on the
label, press the FUNC key (also labeled in gold) followed by the key.
When the FUNC key is pressed, the FUNC indicator is displayed on the
LCD display. If no other key is pressed for 5 seconds, the Function
operation is cancelled and the FUNC indicator disappears.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM11
4-12 Operation with Full Function Handset
4.6.4 Setting the Frequency Mode
The RAY215E can transmit and receive on all available International
marine VHF radiotelephone channels. With a software upgrade, the
RAY215E can also communicate on the US channel set.
Indicators displayed in the LCD identify the active frequency group: US
for the US frequency group, or INT for the International group.
Pressing the FUNC key followed by the INT key alternates the frequency
groups from US mode to International mode then back to US mode. When
the radio is powered on, it starts on Channel 16 in the frequency group
last selected.
Note: Some countries require special licensing to activate the US
channels.
When the frequency group is changed, the channel number remains the
same as was selected in the previous group, as long as that number is
present in the new group. If a channel number is absent in the destination
group, the new channel will be the previous number plus 1. When returning
to the previous frequency group, the channel returns to its original number
if the channel has not been changed. If the channel has been changed, that
number is retained when the frequency group is changed.
Example 1
CH15 INT ⇒ CH15 US ⇒ CH15 INT
When shifting the frequency group, the channel remains the same because
the corresponding channel number exists in the new frequency group.
Example 2
CH2 INT ⇒ CH3 US ⇒ CH2 INT
No corresponding channel exists in the new frequency group, so the
channel is incremented by 1. As long as the channel is not changed further,
it returns to its previous number if the frequency group is again changed.
Example 3
CH2 INT ⇒ CH3 US, then changed to CH5 ⇒ CH5 INT ⇒ CH5 US
However, if the channel is changed in the new frequency group, this new
number is retained when the frequency group is changed.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM12
4-13
Operation with Full Function Handset
4.6.5 Receiving on the Weather Channels
weather channels are only active in US frequency mode and that the NOAA
weather broadcasts can only be heard in the US and Canada.
The US National Oceanic and Atmospheric Administration (NOAA)
broadcasts constant weather reports and storm warnings that can be
received in the US and Canada. If your RAY215E has been programmed
to use the US channel set and the US mode is selected and your vessel is
traveling in waters of the US or Canada, you will be able to receive these
reports.
Note: This feature requires software upgrades for access to the US
frequency group and to the weather channels. Weather channels can be
received only in the US frequency mode when the vessel is located in the
waters of the US or Canada. Some countries required special licensing to
activate the US channel set.
The Weather Channels consist of Channel 0 through Channel 9. These
are separate from the Channels in the regular frequencies set. To switch
between the Working Channel and the current Weather Channel, press
the FUNC key followed by the 6/WX key. While the Weather Channel is
active, the WX indicator appears in the LCD display and the frequency
group indicator disappears.
If the channel number is changed while in the Weather mode, the new
channel number is stored in memory upon exiting Weather mode. To exit
Weather Mode, press CLR, or FUNC followed by 6/WX.
4.6.6 Selecting the Channel
Two methods are available for selecting the channel: inputting the channel
with the numeric keypad then pressing the ENT key, or using the Channel
UP/DOWN switch on the side of the handset. Either method is applicable
to the International and US frequency modes.
Using the Channel UP/DOWN Switch
Pressing the Channel UP
∧∧
∧∧
∧
switch increments the current channel number
by one for each keyclick. When the highest channel number is reached,
the channel scrolls to the lowest number and increments from there.
Pressing the Channel DOWN
∨∨
∨∨
∨
switch decrements the current channel
number by one for each keyclick. When the lowest channel number is
reached, the channel scrolls to the highest number and decrements from
there. Channel numbers not available in a frequency group are skipped.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM13
4-14 Operation with Full Function Handset
If the Channel UP/DOWN switch is pressed and held for at least a half
second, channels automatically change every 100 milliseconds.
Using the Numeric Keypad
To select a channel, input the desired number on the keypad. For 5 seconds
the channel number flashes on the LCD display. If the ENT key is pressed
during this 5 second interval, the channel change is implemented.
If the 5 seconds elapse without pressing another key, the channel change
is implemented anyway. If the CLR key is pressed while the number is
flashing, the channel returns to the previous number.
Note: A leading zero is required for single digit channel numbers.
4.6.7 Selecting the Private Channel
Ten Private Channels have been allocated for specific use within certain
countries. The following table lists the Private Channel designations in
each country and the corresponding RAY215E Private Channel numbers
P1–P10.
You must have the appropriate license and your RAY215E must be
programmed to use the private channel(s) that are approved for your
country.
Note: While using the Private Channel, selecting a new Working Channel
or pressing the CLR key returns operation to the Working Channel.
PrivPriv
PrivPriv
Priv
ateate
ateate
ate
ChannelChannel
ChannelChannel
Channel
FF
FF
F
requencyrequency
requencyrequency
requency
ChannelChannel
ChannelChannel
Channel
CountryCountry
CountryCountry
Country
CH NoCH No
CH NoCH No
CH No
..
..
.
DesignatorDesignator
DesignatorDesignator
Designator
TX/RX (MHz)TX/RX (MHz)
TX/RX (MHz)TX/RX (MHz)
TX/RX (MHz)
UseUse
UseUse
Use
UK P1 M1/37C 157.850/157.850 Pleasure Boat
P2 M2 161.425/161.425 Pleasure Boat
Denmark P3 L1 155.500/155.500 Pleasure Boat
P4 L2 155.525/155.525 Pleasure Boat
Finland, P3 L1 155.500/155.500 Pleasure Boat
Norway & P4 L2 155.525/155.525 Pleasure Boat
Sweden P5 L3 155.650/155.650 Pleasure Boat
Netherlands P6 31A 157.550/162.150
Belgium P6 31A 157.550/162.150
Denmark, P8 F1 155.625/155.625 Fishing Boat
Finland, P9 F2 155.775/155.775 Fishing Boat
Norway & P10 F3 155.825/155.825 Fishing Boat
Sweden
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM14
4-15
Operation with Full Function Handset
Note: A license is required to operate the radio on the private channels.
It is your responsibility to obtain the proper license to operate the radio
on these frequencies.
To select the Private Channel:
1. Press the FUNC key, followed by the 5/PRIV key. The assigned private
channel number appears in the large channel display, preceded by a
“P”. If multiple Private Channels are available, the first channel number
appears.
2. If multiple Private Channels are available, press the CH up/down keys
until the desired Private Channel number appears. The displayed Private
Channel number is selected.
or
Input the private channel number on the keypad. For 5 seconds the
channel number flashes on the LCD display. If the ENT key is pressed
during this flashing phase or the 5 seconds elapse without pressing
another key, the channel is changed. If the CLR key is pressed during
the flashing phase or the number you have selected is not valid, the
channel returns to the previous number.
If Private Channels are not enabled, attempting to access this secondary
function will result in an alarm tone.
The Private Channel is included in the list of channels being scanned
during Scan mode.
4.6.8 Priority Channel
The Priority Channel operates on Channel 16. Pressing the 16 key during
any operation except the Distress Call switches to the Priority Channel.
While using the Priority Channel, pressing the 16 key returns operation to
the Working Channel.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM15
4-16 Operation with Full Function Handset
4.6.9 Multi-Call Operation
The Multi-call function stores as many channels as desired in memory for
quick access to frequently used channels.
Using Multi-Call
To start the Multi-Call operation, press the FUNC key followed by the 8/
M-CALL key. The Multi-Call channel used in the previous operation is
displayed. Use the Channel UP/DOWN key to increment/decrement
through the Multi-Call channels in memory. When exiting Multi-Call, the
last-used channel is stored to be used the next time Multi-Call starts.
Changing from the Multi-Call Channel to the Working Channel
During the Multi-Call operation you can return to the Working Channel
by again pressing FUNC followed by 8/M-CALL, by pressing the CLR
key, or by entering the channel number directly with the ENT key.
Storing the Multi-Call Channel
From the Working or Private Channel mode, select the channel to be stored.
Press and release the FUNC key then press and hold the 8/M-CALL key
for 3 seconds. The MULTI indicator appears when the registration is
complete.
Deleting a Channel from Multi-Call
From the Working or Private Channel mode, select the channel to be
deleted. Press and release the FUNC key then press and hold the 8/M-
CALL key for 3 seconds. The MULTI indicator disappears when the
channel has been deleted.
4.6.10 Channel Memory
Channels that are stored in memory in the same group can be scanned
using the Memory Channel Scan function. Channels can be stored in
memory for each frequency group; when the frequency group is changed,
the radio operates according to the channels stored in memory for that
group.
Storage in memory of Weather Channels or Private Channels is disabled.
When storage of these channels is attempted, the registration is terminated
and an error alert tone sounds.
Storing Channels in Memory
From the Working Channel mode, select the channel to be stored. Press
the FUNC key followed by the 1/MEM key. The MEM indicator appears
when the registration is complete.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM16
4-17
Operation with Full Function Handset
Deleting Channels from Memory
From the Working Channel mode, select the channel to be deleted. Press
the FUNC key followed by the 1/MEM key. The MEM indicator disappears
when the channel is deleted.
4.6.11 Setting the Transmission Power Output
The transmission output can be set at either 1W or 25W. When the power
supply is switched on, the output is 25W. Pressing the FUNC key followed
by the 9/1/25 key alternates the transmission between 25W and 1W.
When 1W is selected, the 1W indicator is displayed on the LCD. When
25W is selected the 1W indicator disappears.
4.6.12 Desensitized Reception (Local Mode)
You can set the RAY215E to reduce the receiving sensitivity in high traffic
areas to decrease unwanted reception. This is also known as local mode.
To select this mode, press the FUNC key followed by the 7/D/L key. While
the desensitize function (local mode) is active, the DESENS indicator
appears in the LCD display. To return to full receiver sensitivity (distant
mode), again press the FUNC 7/D/L key combination.
4.6.13 LCD Backlight Function
LCD backlight brightness can be set at four different levels. Press the
FUNC/DIM key two times to enter Dimmer mode. Each successive click
of the FUNC/DIM key alternates the brightness from Off, to Low, to
Medium, to High, then back to Off. As the backlight setting is changed,
the dot matrix indicator displays the following messages: DIM OFF for
the Off setting, DIM LOW for Low, DIM MID for Medium, and DIM HI
for High.
When the ENT or CLR keys are pressed or when no other key operation
is made for 5 seconds, the current state is accepted and stored in memory,
and the backlight setting operation is complete. The next time the power
supply is switched on, the state of the backlight is recalled and is applied
to each handset individually.
When selecting the DIM OFF setting or pressing any key while in DIM
OFF mode, the display is lit at the DIM LOW setting for 5 seconds and
then turned off. This is so you can view the display in low light conditions.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM17
4-18 Operation with Full Function Handset
4.6.14 Intercom Mode
Intercom mode enables conversation between a Minimum Function
Handset connected to the port on the front of the base station and a full
function handset connected to the port on the rear of the base station.
Note: Using the Intercom is a simplex operation. You must press PTT to
talk to the other station and release PTT to listen.
Making a Call from the Full Function Handset
1. Press the FUNC key followed by the 0/IC key to enter Intercom mode.
IC appears on the large display. While calling, CALLING BASE
appears on the dot matrix display.
When the other station answers the call, the message CALLING turns
to CONNECT.
Note: If the other station does not respond within 60 seconds, the unit
exits Intercom mode.
2. Press PTT to speak to the other station and release PTT to listen.
3. To exit Intercom mode, again press FUNC followed by 0/IC.
Making a Call from the Base Station
1. Press and hold the D/L/I.C. key to enter Intercom mode. IC appears
on the large channel display. While calling, REMOTE flashes on the
small channel display.
When the other station answers the call, REMOTE stops flashing and
appears solid.
Note: If the other station does not respond within 60 seconds, the unit
exits Intercom mode.
2. Press PTT to speak to the other station and release PTT to listen.
3. To exit Intercom mode, again press and hold the D/L/I.C. key.
Receiving a Call from the Full Function Handset
1. When an Intercom call is received, the handset speaker and external
handset speaker both emit a calling tone. If the handset is on the cradle,
the calling tone is not emitted from the handset speaker.
IC appears on the large display and CALL FROM BASE flashes on
the dot matrix display.
2. To answer the call, press PTT. The calling tone ceases and the dot
matrix display goes blank.
Note: If not answered within 60 seconds after being called, the call
terminates and the display returns to its previous state.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM18
4-19
Operation with Full Function Handset
3. Press PTT to speak to the other station and release PTT to listen.
4. To exit Intercom mode, again press FUNC followed by 0/IC.
Receiving a Call from the Base Station
1. When an Intercom call is received, the base station speaker emits a
calling tone. IC appears on the large channel display and REMOTE
flashes on the small channel display.
2. To answer the call, press PTT. The calling tone ceases and REMOTE
stops flashing and appears solid.
Note: If not answered within 60 seconds after being called, the call
terminates and the display returns to its previous state.
3. Press PTT to speak to the other station and release PTT to listen.
4. To exit Intercom mode, again press and hold the D/L/I.C. key.
4.6.15 Scan Mode
During Scan mode, the RAY215E searches through the channels (including
Private Channels), stops when radio traffic is detected, then resumes
scanning after the traffic ceases. Two scan functions are available: All
Channel Scan and Memory Channel Scan. The All Channel Scan function
searches all channels (except the Weather Channels) within the same
frequency group. The Memory Channel Scan searches only the channels
stored in memory in the same group.
The scan begins from the channel following the one currently indicated.
The scan is suspended when a carrier is detected. Five seconds after the
carrier ceases, the scan resumes with the next channel. If the carrier is
detected again before 5 seconds elapse, the timer is re-initialized. Press
the 2/SCAN key to resume the scan from the next channel. Pressing FUNC
followed by 2/SCAN key or pressing the CLR key during the scan cancels
the scan.
Upon reaching Channel 88, the radio scrolls back to Channel 1 and
continues the scan. (If Private Channels have been enabled, they are
scanned following Channel 88.) If the scan stops on a channel with traffic
and you wish to communicate with the other party, press the PTT switch
to cancel the scan and remain on that channel.
Entering a Channel into Memory:
Follow these steps to enter a channel into memory so it can be monitored
during memory scan.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM19
4-20 Operation with Full Function Handset
1. Use the Channel Selection (CH) keys or numeric keypad to select the
Working Channel or Private Channel you wish to enter into memory.
2. Press the FUNC key followed by the 1/MEM key. The MEM indicator
illuminates, indicating that the channel is now in memory.
Using Memory Scan
This function is available only when at least one channel has been stored
in memory.
Press the FUNC key followed by the 2/SCAN key. The messages MEM
and SCAN flash for 3 seconds on the LCD. A scan of only the channels in
memory is initiated when the 3 seconds elapse or when you press the
ENT key before the 3 seconds elapse.
Pressing FUNC followed by 2/SCAN key or pressing the CLR key during
the scan cancels Memory Scan.
Using All Scan
Press the FUNC key followed by the 2/SCAN key The messages MEM
and SCAN flash for 3 seconds on the LCD. Before the 3 seconds elapse,
press the 2/SCAN key again to begin All Scan. If the 3 seconds elapse
before you press the 2/SCAN key, the radio will enter Memory Scan.
Pressing FUNC followed by 2/SCAN key or pressing the CLR key during
the scan cancels All Scan.
4.6.16 Monitor Mode
Monitor operation can be implemented in one of two modes: Dual-Watch
or Tri-Watch.
Dual-Watch
In Dual-Watch Mode, the RAY215E operates on the Working Channel or
Private Channel while constantly monitoring the Priority Channel 16. The
radio locks onto the Priority, Working, or Private Channel whenever it
becomes active, then returns to Dual-Watch when there is no activity.
To start Dual-Watch Mode, select the desired Working Channel or Private
Channel, and then press the MON key. The Working Channel or Private
Channel is displayed on the 7-segment display and the Priority Channel
appears on the right side of the dot matrix display.
To end Dual-Watch mode at the current channel, press the MON key or
the CLR key.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM20
4-21
Operation with Full Function Handset
Tri-Watch
When the RAY215E is using the International frequency set, Tri-Watch
monitors the Working Channel or Private Channel, the Priority Channel
16, and the previously selected Multi-call channel. When a signal is
detected on the Working, Private, Priority, or Multi-call Channels, that
channel becomes active. When there is no longer any activity on the
channel, the RAY215E returns to Tri-Watch.
If the RAY215E has received an upgrade to use the US channel set, and
US mode is selected, Tri-Watch monitors the Working Channel or Private
Channel, the Priority Channel 16, and the previously selected Weather
Channel for severe weather alert broadcasts. When a signal is detected on
the Working, Private, or Priority Channel, that channel becomes active.
When there is no longer any activity on the Working Channel or Priority
Channel, the RAY215E returns to Tri-Watch.
If a weather alert broadcast is detected, the RAY215E emits an alert tone
and the WX indicator blinks. Tri-Watch mode terminates and the radio
switches to the WX channel to monitor the severe weather broadcast.
To start Tri-Watch mode, select the Working Channel or Private Channel,
and then press the FUNC key followed by the MON/TRI key. The Working
Channel appears on the 7-segment display, the Priority Channel appears
on the right-most portion of the dot matrix display, and the Multi-call or
Weather Channel appears on the left-most portion of the dot matrix display.
(If the Private Channel is being used, the Working Channel appears in the
left-most portion of the dot matrix display.)
To end Tri-Watch mode at the current channel, press the MON key or the
CLR key.
4.6.17 NMEA Operation
The RAY215E with a Full Function Handset can receive valid position
and time information, which are transmitted during a DSC Distress call.
This data can be communicated via NMEA 0183 from a GPS, fishfinder,
radar, or any device that outputs GPS sentences. If the radio does not
detect the positional data, it provides different alerts urging you to find
and correct the fault or manually input the data using the radio’s L/L ENT
function, as described in Section 4.7.3.2. Current valid positional data,
whether from external device or manually input, can be viewed using the
NAVSTAT Operation described in Section 4.7.2.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM21
4-22 Operation with Full Function Handset
If a GPS device is not connected via NMEA, the radio emits a 5-second-
long staccato alert tone and flashes the NMEA indicator 2 minutes after
power up. This occurs every time the unit is turned on. The alarm is required
by safety regulations and cannot be disabled.
Operation at Power Up
At power up, the radio monitors the NMEA line for 1 minute. If a signal
is detected on NMEA, the radio determines whether the data is valid. If
valid, the data is accepted and the NMEA indicator is displayed on the
LCD.
If no GPS signal is detected on NMEA after the 1 minute monitoring
period, a 5-second-long staccato alert tone is emitted and the NMEA
indicator flashes. All the position fields are set to 9’s and the time and
date fields are set to 8’s. The message NO GPS appears in the NAVSTAT
screen, although no positional data is displayed.
If at a later time valid data is received on NMEA, the data is accepted and
the NMEA indicator is displayed solid (no longer flashing).
Operation When the Signal is Lost or Becomes Invalid
If positional data that was previously detected becomes invalid or is no
longer detected, the radio monitors the NMEA line for 1 minute for it to
be restored.
If a signal is restored on the NMEA line and the radio determines the data
is valid, the data is accepted and the NMEA indicator returns to a solid
state (not flashing).
However, if no signal is detected, the NMEA indicator flashes and a 5-
second-long staccato alert tone is emitted. The last received positional
data is retained in memory and can be viewed in the NAVSTAT screen.
The message NO GPS appears in NAVSTAT in the position where the
type of device used to be. The NMEA indicator continues to flash until
valid positional data is received. If valid positional data (from the same
source) is later restored, the NMEA indicator is again displayed solid.
Operation When No Signal Detected for 4 Hours
If no valid positional data is received or input manually within 4 hours of
the previous alert, the NMEA indicator continues to flash and the staccato
alert tone is again emitted. This pattern is repeated every 4 hours if no
positional data has been detected. If no manual input was made during
the previous 23.5 hours, all the position fields are set to 9’s and the time
and date fields are set to 8’s.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM22
4-23
Operation with Full Function Handset
4.6.18 Digital Selective Calling (DSC)
The Digital Selective Calling (DSC) protocol is a globally applied system
used to send and receive digital Distress calls as well as Individual and
All-Ships calls on channel 70, the dedicated DSC channel for Marine
VHF. For a Distress call transmission, the RAY215E with a Full Function
Handset takes the position and time information from the input NMEA
data along with your Maritime Mobile Station Identifier (MMSI) and
converts it into a digital "packet". When transmitted, this digital information
lets other ships and shore stations equipped with appropriate DSC
equipment know where you are and that you are in a Distress situation.
Communications in DSC mode include the following:
1. Transmitting/Receiving an Individual Call
2. Transmitting/Receiving a Group Call
3. Transmitting/Receiving an All Ships Call
4. Transmitting/Receiving a Distress Call
5. Receiving a Distress Relay Call
DSC transmission and reception occurs on Channel 70. When the DSC
signal is received, the unit quickly switches over to Channel 70 and
performs the corresponding operation. You will not receive a DSC call if
the radio is transmitting.
Note: An MMSI number is required to operate the DSC equipment in this
radio. You can program the MMSI number yourself one time only using
the Menu Operation described in 4.5.4.2 MMSI Number Set Up.
Otherwise, your Raymarine dealer can program or change the number
for you.
DSC calls come in three varieties: ROUTINE for normal calls, SAFETY
for advisory alerts, and URGENCY for assistance when life is not in
immediate danger.
4.6.18.1 Individual Call to Another Ship (Ship-to-Ship)
An Individual Ship's Call is a DSC call made to a specific ship identified
by its MMSI number. The RAY215E can receive all three types of
Individual calls but can only transmit ROUTINE Individual calls. As with
any DSC operation, the call is made on Channel 70.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM23
4-24 Operation with Full Function Handset
Transmitting an Individual Call
To call another ship, you must select the Working Channel and a specific
MMSI number. The MMSI number is selected either manually or from a
Phonebook list of preprogrammed numbers specified using the MENU
function. To cancel the call, press and hold the CLR key for 3 seconds.
Press the INDV key to initiate the call data setup operation. After setting
the call data, press the PTT switch to send the call.
To Make an Individual Call to Ship (ship-to-ship):
1. Press the INDV key. Ind appears on the 7-segment display and the
DSC indicator is displayed. Pressing the SQ UP/DOWN key alternates
between SHIP and SHORE.
INDV
Alternates with each click
of the SQ UP/DOWN key
2. Select SHIP and press the ENT key.
3. Scroll with the SQ UP/DOWN keys to select the method for inputting
the MMSI number, either from the Phonebook or manually. Press ENT.
ENT
Alternates with each click
of the SQ UP/DOWN key
4. Select the MMSI number.
BY PHONEBOOK:
Scroll with the SQ UP/DOWN keys, select the name associated with
the desired MMSI number, and press the ENT key. If the MMSI number
is not listed in phonebook, the display reverts to manual input.
ENT
Use SQ UP/DOWN key
to scroll through list of
MMSI nos./nicknames
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM24
4-25
Operation with Full Function Handset
Note: The full function handset provides you with a phonebook that holds
entries for up to 20 Ship stations and 20 Shore stations. These are separate
from the 10 phonebook entries stored in the base station using the Minimum
Function Handset (see Section 3.5.18.2). These 10 entries cannot be
selected with the full function handset.
BY MANUAL INPUT:
Input the 9-digit MMSI number with the numeric keypad, then press
the ENT key.
ENT
numeric
keypad
Flashing
Flashing
5. Specify the Working Channel with the SQ UP/DOWN keys and press
the ENT key.
ENT
SQ UP/
DOWN
6. Press the ENT key again. A prompt appears on the display instructing
you to press the PTT switch.
7. Press PTT to transmit.
ENT ENT
MMSI number or
nickname is displayed
Note: Only simplex channels (those channels that transmit and receive
on the same frequency) can be selected for ship to ship Individual Calls.
Pressing the SQ UP/DOWN will scroll you through the simplex channels
usable for this operation.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM25
4-26 Operation with Full Function Handset
Note: The working channel selected for the Individual Call is inserted as
the working channel in item #5 above as long as it is an intership simplex
channel. If it is not, the radio selects the next higher simplex channel to
insert as the working channel.
Response
If a response is received after pressing the PTT switch, a receive-
confirmation message is displayed. After 5 seconds have elapsed, the
channel is changed to a communication channel and the Individual Ships
Call is completed.
ACK 5 sec
If no response is received for 3 minutes after pressing the PTT switch, a
prompt to press the PTT switch appears once more. After 15 seconds
elapses without pressing the PTT switch following the prompt, operation
returns to the state before the call.
NO ACK
Scrolls every second
3 min
PTT PTT
4.6.18.2 Individual Call to Shore Station (Ship-to-Shore)
To call a shore station, you must select the specific MMSI number. The
MMSI number can be entered manually or selected from a Phonebook
list of preprogrammed numbers. Channel 16 is automatically assigned for
communications. To cancel the call, press and hold the CLR key for 3
seconds.
To make an Individual Call to Shore Station (ship-to-shore):
1. Select the Shore Station channel.
2. Press the INDV key. Ind appears on the 7-segment display and the
DSC indicator is displayed. Pressing the SQ UP/DOWN key alternates
between SHIP and SHORE.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM26
4-27
Operation with Full Function Handset
INDV ENT
Alternates with each
click of SQ UP/DOWN
After pressing ENT, the
indication switches to:
PHNBOOK, MANUAL
3. Select SHORE and press the ENT key.
4. Scroll with the SQ UP/DOWN keys to select the method for inputting
the MMSI number, either from the phonebook or manually. Press ENT
to input your selection.
5. Select the name by MMSI number from the phonebook by scrolling
with the SQ UP/DOWN keys, and pressing the ENT key.
ENT
SQ UP/
DOWN
ENT
Use SQ UP/DOWN key to scroll through
list of MMSI nicknames. Press ENT when
desired selection is displayed.
Note: The full function handset provides you with a phonebook that
holds entries for up to 20 Ship stations and 20 Shore stations. These
are separate from the 10 phonebook entries stored in the base station
using the Minimum Function Handset (see Section 3.5.18.2). These
10 entries cannot be selected with the full function handset.
or
Manually input the MMSI number with the numeric keypad, then press
the ENT key.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM27
4-28 Operation with Full Function Handset
ENT
numeric
keypad
Flashing
Flashing
6. Press ENT again. A prompt appears on the display instructing you to
press the PTT switch.
7. Press PTT to transmit.
ENT
With manual input, MMSI
number would be displayed
Response
If a response is received after pressing the PTT switch, a receive-
confirmation message is displayed. After 5 seconds have elapsed, the
channel is shifted to a communication channel and the Individual Call is
completed.
ACK 5 sec
If no response is received for 3 minutes after pressing the PTT switch, a
prompt to press the PTT switch appears once more. If the PTT switch is
not pressed within 15 seconds after the prompt appears, operation returns
to the state before the call.
NO ACK
Scrolls every second
3 min
PTT
PTT
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM28
4-29
Operation with Full Function Handset
4.6.18.3 Receiving an Individual Call
When an Individual Call is received, the DSC indicator flashes, Ind
appears on the 7-segment display, and the DSC Received Alert is sounded.
On the dot matrix display appears the message RECEIVED IND CALL
along with the type of call: ROUTINE, SAFETY, or URGENCY. If the
MMSI number exists in the Phonebook list, the associated name is also
displayed. If no match is found, the actual numeric value of the MMSI is
displayed. Lastly, a prompt appears to press ENT to accept or CLR to log
the call. This sequence scrolls every second.
Until either the ENT key or the CLR key are pressed, the prompt is flashed
at 1-second intervals and is accompanied by an alarm for up to 3 minutes.
If neither ENT nor CLR are pressed during these 3 minutes, the radio
places the incoming call into the DSC log and reverts to the operation
mode that was active before the Individual Call was received. The DSC
indicator continues to be flashed on the LCD display until the contents of
the log files can be confirmed
If ENT is pressed, the alarm is turned off, and a new prompt appears on
the display, instructing you to press the PTT switch. Press PTT to transmit
an acknowledgment (ACK). If PTT is not pressed within 5 seconds of the
prompt appearing, the transmission is done automatically. Pressing the
PTT switch causes the channel to change to the communication channel.
Scrolls
every
second
If the CLR key is pressed
Receiving
ENT
MMSI number is displayed
if the nickname is not
registered in the list.
After no operation
for 5 seconds
If the CLR key is pressed, the alarm is turned off, the displays are cleared,
and the received contents are stored in the Log File. The radio then reverts
to the operation mode before receiving the Individual Call.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM29
4-30 Operation with Full Function Handset
4.6.18.4 Transmitting a Group Call
You can send and receive DSC calls from groups of stations that share the
same MMSI number.
The RAY215E can only transmit ROUTINE Group calls. As with any
DSC operation, the call is made on channel 70.
To make a Group Call:
1. Set up the Group MMSI number as outlined in Section 4.7.3.4.
2. Press the INDV key. Ind appears on the 7-segment display, the DSC
indicator is illuminated, and SHIP appears on the dot matrix display.
3. Press the SQ UP/DOWN key to alternate between SHIP, SHORE,
and GROUP. Stop on GROUP. The GROUP message only appears if
you have set up the Group MMSI number as outlined in Section 4.7.3.4.
4. When GROUP appears, press the ENT key. GrP appears on the 7-
segment display and the registered Group MMSI number appears on
the dot matrix display.
INDV ENT
Only appears if Group
MMSI number is set up
via DSC Operation in
Menu Mode
Group MMSI number
Note: Since only one group MMSI number can be registered at time, only
one MMSI number can be displayed when GROUP is selected. To change
the group MMSI number, see Section 4.7.3.4.
5. Press ENT to accept the MMSI number.
6. Use the SQ UP/DOWN key to select the Working Channel for
communication.
7. When the desired channel number appears, press ENT. The dot matrix
display scrolls between the Working Channel and the Group MMSI
number.
8. If this information is correct, press ENT to accept. A new message
appears, prompting you to press the PTT switch.
RAY215_EURO Sect4.p65 2/14/2002, 6:28 PM30
4-31
Operation with Full Function Handset
9. Press PTT. The radio changes over to the selected Working Channel
without waiting for acknowledgment.
ENT
ENT
MMSI number
Select Working Chanel
with SQ UP/DOWN key
Scrolls between
Working Chanel and
MMSI number
ENT
PTT
4.6.18.5 Receiving a Group Call
When a Group Call is received, the DSC indicator flashes, Grp appears
on the 7-segment display, and the DSC Received Alert is sounded. On the
dot matrix display appears the message RECEIVED GRP CALL. If the
MMSI number exists in the list, the associated name is displayed. If no
match is found, the actual numeric value of the MMSI is displayed. You
are then prompted to press ENT to accept or CLR to log the call.
Until either the ENT key or the CLR key are pressed, the prompt is flashed
at 1-second intervals and is accompanied by an alarm for up to 3 minutes.
If neither ENT nor CLR are pressed during these 3 minutes, the radio
reverts to the operation mode before receiving the Group Call. The DSC
indicator continues to be flashed on the LCD display until the contents of
the log files can be confirmed.
If ENT is pressed, the alarm is turned off, and a new prompt appears on
the display, instructing you to press the PTT switch. Press PTT to transmit.
If PTT is not pressed within 5 seconds of the prompt appearing, the
transmission is done automatically. Pressing the PTT switch causes the
channel to change to the communication channel.
If the CLR key is pressed, the alarm is turned off, the displays are cleared,
and the received contents are stored in the Log File. The radio then reverts
to the operation mode before receiving the Group Call.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM31
4-32 Operation with Full Function Handset
Scrolls
across
display
Receiving ENT
MMSI number is displayed
if the nickname is not
registered in the list.
4.6.18.6 Transmitting an All Ships Call
The All Ships Call is used to send out a message to all ships in range that
you need assistance but the situation is not serious enough for a Distress
Call. This call should only be used if hailing for assistance on 16 fails.
The RAY215E can transmit and receive all three types of All Ships Calls:
ROUTINE, SAFETY, and URGENCY. The RAY215E can transmit only
SAFETY and URGENCY. As with any DSC operation, the call is made
on channel 70. Then, after the All Ships Call is sent or received, the radio
automatically selects channel 16.
To send an All Ships Call
1. Press the ALL SHIP key. The message SAFETY appears on the dot
matrix display and the DSC indicator illuminates.
2. Press the SQ UP/DOWN key. The message URGENCY now appears
on the dot matrix display.
3. Make your selection between SAFETY or URGENCY and press the
ENT key to submit. The prompt RECONFIRM is displayed.
4. Press the ENT key to confirm. A prompt appears on the display,
instructing you to press the PTT switch.
5. Press PTT to transmit.
The All Ships Call is made on Channel 70. After the All Ships Call is sent,
the radio automatically switches to channel 16.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM32
4-33
Operation with Full Function Handset
ENT ENT
Alternate by pressing the
SQ UP/DOWN key
4.6.18.7 Receiving an All Ships Call
When an All Ships Call is received, an alert is sounded. The LCD displays
the type of All Ships call being received, along with the sender's MMSI
number, and a prompt to press ENT to accept or CLR to log the call. The
DSC Distress alert and the displayed message continue until either ENT
or CLR is pressed. If ENT is pressed, the radio switches to Channel 16
and the contents of the communication are stored in the log. If CLR is
pressed, the radio reverts to the mode before receiving the URGENCY
Call and the contents are stored in the log.
ENT
If CLR is pressed, the radio
reverts to the mode before
receiving Urgency Call
CLR
4.6.18.8 Transmitting a Distress Call
A Distress Call allows you to send out a digital "packet" of data at high
power that includes your position, time, and MMSI number. All ships and
stations outfitted with the correct type of DSC equipment will be able to
pinpoint your position and either relay the information or respond directly.
Using the Distress key overrides all other functions.
Two types of Distress Calls can be made: one that specifies the type of
distress and one that does not.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM33
4-34 Operation with Full Function Handset
Unspecified Distress Call
To make a Distress Call without specifying type of distress:
1. Open the door labeled DISTRESS on the back of the handset and
press and hold the DISTRESS button. After one second, dSr flashes
on the 7-segment display and the DSC indicator appears. On the dot
matrix display, countdown message appears prompting you to hold
the DISTRESS key for 4 more seconds.
2. Continue to hold the DISTRESS button for the duration of the
countdown. An alert tone is sounded at one-second intervals.
press
DISTRESS
Countdown starts 1 second after pressing
DISTRESS key. The types of DISTRESS
can be selected by releasing the key
before the Countdown is completed.
Note: If you fail to hold the button for the full 5 seconds, the DISTRESS
call is cancelled.
3. After the countdown has completed, the message RELEASE appears
on the dot matrix display. Release the DISTRESS button.
The unit switches to channel 16, displays the message AWAIT ACK,
and monitors channel 70 for an acknowledgment.
release
DISTRESS
The unit retransmits the DISTRESS call at random intervals of 3.5 to 4.5
minutes, until a response is received or the call is manually cancelled.
To cancel the DISTRESS call, press the CLR key and hold for 3 seconds.
The call is cancelled and the unit returns to the state before the call.
Note: When a Distress Call is sent, an alarm is sounded at maximum
volume on the external speaker, even if the volume knob has been rotated
all the way OFF. You can mute the alarm tone by pressing the CLR key
for one second. Pressing CLR only turns off the alarm; it does not interrupt
the Distress Call.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM34
4-35
Operation with Full Function Handset
press and hold
CLR for 3 secs
When a response is received, the DSC indicator flashes and the DSC
Distress alert is sounded. The LCD scrolls a message that the DISTRESS
has been acknowledged, along with the sending station's MMSI number
or nickname. The message and alert are repeated until the CLR key is
pressed.
CLR
Flashing
When the CLR key is pressed, the unit exits the DSC mode continues
monitoring Channel 16 on high power.
Regardless of the handset state, the DSC Distress alert is sounded at
maximum volume on the external speaker, even if the volume knob has
been rotated all the way OFF.
You can mute the alert tone by pressing the CLR key for one second.
Pressing CLR only turns off the alert sound; it does not interrupt the
Distress call.
Specified Distress Call
You can assign one of eleven distress types to the call to provide the
potential rescuing station additional information if time and circumstances
permit. The Nature of the distress call can be selected using the DISTRESS
key as outlined below or in the system MENU as outlined in Section
4.7.3.1. Below are the messages and their meanings:
MessageMessage
MessageMessage
Message
MeaningMeaning
MeaningMeaning
Meaning
MessageMessage
MessageMessage
Message
MeaningMeaning
MeaningMeaning
Meaning
FIRE fire ADRIFT drifting
FLOODNG flooding UNDESIG undesignated
COLLISN collision ABNDSHP abandoning ship
AGROUND run aground PIRACY piracy
LISTING listing MANONBD man overboard
SINKING sinking
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM35
4-36 Operation with Full Function Handset
To make a Distress Call specifying the type of distress:
1. Open the door labeled DISTRESS on the back of the handset and
press and release the DISTRESS key on the back of the handset. dSr
appears on the 7-segment display and the DSC indicator illuminates.
On the dot matrix display, the message FIRE appears.
press and
release
DISTRESS
SQ UP/
DOWN
2. If FIRE is the message you wish to attach, press the ENT key.
OR
If FIRE is not the message you wish to attach, scroll through the list
with the SQ UP/DOWN keys. When the appropriate message is
displayed, press the ENT key.
On the dot matrix display, appears the distress type plus a message
prompting you to press and hold the DISTRESS key.
3. To send the distress signal, press and hold the DISTRESS key. After
one second, dSr flashes and a countdown message appears on the dot
matrix display, prompting you to hold the DISTRESS key for 4 more
seconds.
hold
DISTRESS
4. Continue to hold the DISTRESS key for the duration of the countdown.
A tone sounds every second.
Note: If you fail to hold the button for the full 5 seconds, the DISTRESS
call is cancelled.
After the 5 seconds have elapsed, the message RELEASE appears,
prompting you to release the key.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM36
4-37
Operation with Full Function Handset
5. When this prompt appears, release the DISTRESS key. The unit is
switched to Channel 16, displays the message AWAIT ACK, and
monitors channel 70 for an acknowledgment.
release
DISTRESS
dSr stops flashing and the distress alarm sounds continuously. The
unit retransmits the DISTRESS call at random intervals of 3.5 to 4.5
minutes, until a response is received or the call is manually cancelled.
To cancel the DISTRESS call, press the CLR key and hold for 3 seconds.
The call is cancelled and the unit returns to the state before the call.
press and hold
CLR 3 seconds
When a response is received, the DSC indicator flashes and the DSC
Distress alert is sounded. The LCD scrolls a message that the DISTRESS
has been acknowledged, along with the sending station's MMSI number.
The message and alert are repeated until the CLR key is pressed.
When the CLR key is pressed, the unit exits the DSC mode and continues
monitoring Channel 16. Regardless of the handset state, the DSC Distress
alert is sounded at maximum volume on the external speaker.
4.6.18.9 Receiving a Distress Call
When a Distress call is received, the DSC indicator flashes, dSr appears
on the 7-segment display, and the DSC Distress alert is sounded. On the
dot matrix display are scrolled RECEIVED, DISTRESS, the type of
distress, the MMSI number, the transmitting time, the latitude, and
longitude of the transmitting station.
The DSC Distress Alert and the displayed message continue until either
ENT or CLR are pressed. Pressing ENT stores the contents of the call
in the log and switches the radio to Channel 16. Pressing CLR also logs
the call but then reverts the radio to the mode before receiving the
Distress call.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM37
4-38 Operation with Full Function Handset
ENT
If CLR is pressed, the radio
reverts to the mode before
receiving Distress Call
CLR
4.6.18.10 Receiving a Distress Relay Call
Sometimes a ship’s distress call can be relayed from another ship or a
shore station. The RAY215E can only receive a Relayed Distress call that
has been addressed to All Ships.
When a Relayed Distress call is received, the DSC indicator flashes, dSr
appears on the 7-segment display, and the DSC Distress alert is sounded.
On the dot matrix display are scrolled RECEIVED, RELAY, the MMSI
number of the station making the call, DISTRESS, the type of distress,
the MMSI number of the ship in distress, the latitude and longitude of
that ship, and the time of transmission.
ENT or CLR
MMSI number of transmitting station. If registered
in the list, the nickname appears instead.
MMSI number of ship in distress. If not
known, UNKNOWN appears here instead.
The displayed message continues until either ENT or CLR is pressed. At
that time, the radio switches to Channel 16 in high power and the contents
of the communication are stored in the Log File.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM38
4-39
Operation with Full Function Handset
4.6.19 ATIS Operation
The RAY215E comes equipped with Automatic Transmission
Identification System (ATIS) capability for inland waterway requirements
in Europe. With ATIS enabled, each time the PTT switch is pressed your
station ID is sent at the end of the transmission. Before utilizing this feature,
you must obtain an ID number, program it into the RAY215E’s system
Menu, and activate the ATIS feature. Once activated, ATIS can be enabled
or disabled in the system Menu so that the RAY215E can be used in open
water or inland waterways.
4.7 Menu Operation
The menu operation is used for making various settings and confirming
the current state. The operation is roughly divided in three functions as
follows:
FunctionFunction
FunctionFunction
Function
PurposePurpose
PurposePurpose
Purpose
1. NAVSTA Indicates the information input from NMEA.
2. DSC To register/modify various settings related to DSC.
3. SETTING To program the MMSI number, to program ATIS ID number
and to set the operation mode of ATIS
4.7.1 Selecting the Menu Operation
To initiate the Menu function:
1. Press the FUNC key followed by the MENU key. Mn appears on the
7-segment display and NAVSTAT is shown on the dot matrix display.
2. To scroll through these first level menu items, press the SQ UP/DOWN
key. The indicators alternate between NAVSTAT, DSC, and SETTING.
3. Select the desired operation and press the ENT key to enter that
particular menu item.
To exit the Menu operation, press and hold the CLR key for 3 seconds.
FUNC
+
MENU
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM39
4-40 Operation with Full Function Handset
4.7.2 NAVSTAT Operation
This operation indicates on the LCD display the position information that
has been input via NMEA or has been manually input using the LL/ENT
function as outlined in Section 4.7.3.2.
To view current position information:
1. Press the FUNC key followed by the MENU key to initiate the Menu
operation.
2. Select NAVSTAT and press the ENT key. The following five items
are automatically displayed at 3-second intervals in the following order:
1. Latitude 4. UTC Date (Y/M/D)
2. Longitude 5. Position source (GPS, DIFF GPS, NO GPS)
3. UTC Time
This data is for viewing only and can not be altered.
3 secs
3 secs
after 3 seconds elapse
3 secs 3 secs
To return to the main menu screen, again press FUNC followed by MENU.
To exit the Menu operation, press and hold the CLR key for 3 seconds.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM40
4-41
Operation with Full Function Handset
4.7.3 DSC Operation
DSC operation includes the manual entry of latitude/longitude, listing of
other ship’s MMSI numbers for ship-to-ship and ship-to-shore
communications, and listing of Group MMSI number.
To initiate the DSC operation:
1. Press the FUNC key followed by the MENU key to initiate the Menu
operation.
2. Select DSC and press the ENT key. The 7-segment display shows
dSC and the dot matrix display shows L/L ENT.
The DSC Main Menu is made up of NATURE, L/L ENT, PHNBOOK,
and GROUP submenus.
SQ UP/DOWN
3. Press the SQ UP/DOWN key until the desired operation is
displayed:
NATURE Select type of Distress Call
L/L ENT Manual entry of latitude/longitude
PHNBOOK Listing of Other Ship’s MMSI number for Ind. Calls
GROUP Listing of Group MMSI number
4. Press the ENT key to submit.
4.7.3.1 Selecting Distress Call Type (NATURE)
This menu item is used to select the nature of a distress call before the call
is sent. The selected information will be sent along with the distress call.
To select the nature of the distress that will be included with the call:
1. As described in Section 4.7.3 DSC Operation above, select the DSC
operation NATURE.
2. Press the ENT key to initiate the process. The 7-segment display shows
nAt and the dot matrix display shows FIRE.
3. Use the SQ UP/DOWN key to select the type of distress.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM41
4-42 Operation with Full Function Handset
ENT
ENT
Select
with
SQ UP/
DOWN
4. After selecting the desired distress type, press ENT. You are prompted
to press the DISTRESS key.
5. To send the distress call at this time, press and hold the DISTRESS
button. Follow the instructions on the display or the steps described in
Section 4.6.18.8.
6. To cancel the distress call, press and hold CLR for 3 seconds.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM42
4-43
Operation with Full Function Handset
4.7.3.2 Manual Entry of Latitude/Longitude (L/L ENT)
This operation is used to manually enter the latitude/longitude and UTC
time when normal NMEA input of the position information is not available.
The radio will sound a 5-second-long alert tone every four hours to remind
you to update your position.
1. As described in Section 4.7.3 DSC Operation above, select the DSC
operation L/L ENT. The 7-segment display shows L L, while the dot
matrix display shows the latest latitude data.
2. Press one of the following keys to initiate the corresponding
operation:
KK
KK
K
eyseys
eyseys
eys
ActionAction
ActionAction
Action
0 - 9 keys Changes the flashing numeric value (see step 3), then
advances to the next digit's place.
ENT key Advances from Latitude, to Longitude, to UTC.
CLR key Returns to the previous subject item.
SQ UP/ For Latitude, alternates between N and S.
DOWN key For Longitude, alternates between E and W.
For UTC, no effect.
3. The subject items can be changed in the following order. Numeric
values that can be changed are flashing:
1. Degrees of lat at ten’s place 8. Minutes of lon at ten’s place
2. Degrees of lat at unit's place 9. Minutes of lon at unit's place
3. Minutes of lat at ten’s place 10. Hours of UTC at ten’s place
4. Minutes of lat at unit's place 11. Hours of UTC at unit's place
5. Degrees of lon at hundred’s place 12. Minutes of UTC at ten’s place
6. Degrees of lon at ten’s place 13. Minutes of UTC at unit’s place
7. Degrees of lon at unit's place
4. After changing the subject item, the display scrolls from latitude to
longitude to UTC. To submit the change of the position data as shown
in the display, press the ENT key. The unit exits Menu mode and returns
to normal operation.
To exit the Menu operation, press and hold the CLR key for 3 seconds.
The following illustration shows an example of the operation:
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM43
4-44 Operation with Full Function Handset
press ENT
press ENT
press 5
press 7
press ENT press 0
press 7press ENT
press 2
press 0
press ENT
press 1
press ENT
press ENT
press ENT
press ENT
press ENT
Flashing Flashing
Flashing
Flashing Flashing
Flashing
Flashing
FlashingFlashing Flashing
Flashing
Flashing
press ENT
Flashing
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM44
4-45
Operation with Full Function Handset
4.7.3.3 Modifying the MMSI Number List (PHNBOOK)
This operation is used to modify the "phonebook" lists of MMSI numbers
used for DSC Individual Calls. Two lists are available: one for Ship stations
and one for Shore stations. Each list allows you to register the MMSI
number and nickname for up to 20 Ship and 20 Shore stations.
Note: The 20 Ship stations and 20 Shore stations in this phonebook are
separate from the 10 phonebook entries stored in the base station using
the Minimum Function Handset (see Section 3.5.18.2). All 50 entries are
available for you to use.
1. As described in section 4.7.3 DSC Operation above, select the DSC
operation PHNBOOK.
2. Press the ENT key to initiate the process. The 7-segment display shows
Phb and the dot matrix display shows SHIP.
ENT
3. Use the SQ UP/DOWN key to select between SHIP or SHORE.
4. Press the ENT key to turn to submit your selection.
Modifying the List of Ship Stations
In this operation, a ship is registered (added) to or deleted from the
phonebook list for ship stations.
1. When SHIP is displayed, press the ENT key. The 7-segment display
shows SHP, while the dot matrix display shows ENTRY.
2. The list can hold a maximum of 20 entries. If a list is already full or if
the list becomes full during this process, the indicator PHNBOOK IS
FULL is displayed.
3. To delete an item from the list, use the SQ UP/DOWN key to select
DELETE and press the ENT key. If no station has yet been registered,
the message PHNBOOK IS EMPTY is displayed.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM45
4-46 Operation with Full Function Handset
ENT
Note: Pressing and holding the CLR key for 3 seconds during either
ENTRY or DELETE returns operation to the mode before the Menu
operation began.
Adding Ship Stations to the List
To add to the phonebook list for ship stations, input the MMSI number
and nickname of the station.
1. To enter the MMSI number, press the corresponding numeric keys (0
through 9). The currently selected location is indicated by a flashing
"–" character. Pressing a numeric key enters that value then advances
to the next digit's place. To go back by 1 digit, press the CLR key.
2. To enter the nickname, use the numeric keys (0 through 9) to input the
associated alpha or numeric value. The currently selected location is
indicated by the flashing "–" character. After inputting the desired
letter or numeral, press the ENT key to submit the entry and proceed
to the next place.
To go back by 1 digit, press the CLR key.
If no nickname is to be registered, press the ENT key for all characters
so that they all display a "–".
3. When the message CONT? Y appears, press the ENT key to submit.
Note: The 0 key will enter only the numeral "0", while the 1 key will
alternately enter "1" and "space". The 0 and 1 keys do not have associated
alpha characters.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM46
4-47
Operation with Full Function Handset
ENT
ENT
0
ENT
7/PQRS
(twice)
2/ABC
ENT
ENT
Flashing
FlashingFlashing
Flashing Flashing Flashing
This display is shown only if the list already
has the maximum 20 stations registered
Pressing ENT while "N" is displayed
exits Menu mode without registering
the station.
Pressing ENT while "Y" is displayed
registers the station and exits Menu
mode.
ENT
Input remainder
of MMSI name
Input remainder
of MMSI number
Deleting Ship Stations from the List
When the ship station phonebook is selected, the oldest MMSI number or
nickname flashes on the dot matrix display.
1. Follow instructions in 4.7.3.3 Modifying the MMSI Number List
(PHNBOOK) to enter the phonebook.
2. When SHIP is displayed, press the ENT key. The 7-segment display
shows SHP, while the dot matrix display shows ENTRY.
3. Using the SQ UP/DOWN keys, scroll until DELETE appears on the
dot matrix display.
4. Press ENT. The oldest nickname and MMSI flash on the dot matrix
display.
5. If this is the item to be deleted, press the ENT key
If this is not the number to be deleted, use SQ UP/DOWN until it is
displayed.
6. Press ENT. The message DEL? Y is displayed on the 7-segment
display.
7. Press the ENT key to process the deletion and exit the Menu operation.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM47
4-48 Operation with Full Function Handset
To exit without deleting, press the SQ UP/DOWN key until DEL? N
is displayed. If the list has no stations entered, the message PHNBOOK
IS EMPTY HOLD DOWN CLR KEY is displayed. Press and hold
the CLR key for 3 seconds to exit Menu mode.
ENT ENT
Modifying the List of Shore Stations
In this operation, a shore (coast) station is registered (added) to or deleted
from the phonebook list.
1. Follow instructions in 4.7.3.3 Modifying the MMSI Number List
(PHNBOOK) to enter the phonebook.
2. When SHORE is displayed, press the ENT key. SHO appears on the
7-segment display, while on the dot matrix display shows ENTRY.
3. The ENTRY selection is used to register (add) an item to the list. Press
the ENT key to accept.
The list can hold a maximum of 20 entries. If a list is already full or if
the list becomes full during this process, the indicator PHNBOOK IS
FULL is displayed.
4. To delete an item from the list, use the SQ UP/DOWN key to select
DELETE and press the ENT key. If no station has yet been registered,
the message PHNBOOK IS EMPTY is displayed.
ENT
Note: Pressing and holding the CLR key for 3 seconds during either
ENTRY or DELETE returns operation to the mode before the Menu
operation began.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM48
4-49
Operation with Full Function Handset
Adding Shore Stations to the List
To add to the phonebook list for shore stations, input the MMSI number
and nickname of the station.
1. To enter the MMSI number, press the corresponding numeric keys
(0 through 9). The currently selected location is indicated by a flashing
"–" character. Pressing a numeric key enters that value then advances
to the next digit's place. To go back by 1 digit, press the CLR key.
2. To enter the nickname, use the numeric keys (0 through 9) to input
their associated alpha or numeric value. The currently selected location
is indicated by a flashing "–" character. After inputting the desired
letter or numeral, press the ENT key to submit the entry and proceed
to the next place. To go back by 1 digit, press the CLR key.
3. When the message CONT? Y appears, press the ENT key to submit
the registration.
If no nickname is to be registered, press the ENT key for all characters
so that they all display a "–".
ENT1-8 0
ENT
ENT
7/PQRS
(twice)
2/ABC
ENT ENT
ENT
To DELETE mode
Flashing
FlashingFlashing
Flashing FlashingFlashing
If the maximum 20 stations are already
registered, this display is shown and the
radio shifts to Delete mode
Pressing ENT while "N" is displayed
exits Menu mode without registering
the station.
Pressing ENT while "Y" is displayed
registers the station and exits Menu
mode.
ENT
Input remainder
of MMSI number
Input remainder
of MMSI name
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM49
4-50 Operation with Full Function Handset
Note: The 0 key will enter only the numeral "0", while the 1 key will
alternately enter "1" and "space". The 0 and 1 keys do not have associated
alpha characters.
Deleting Shore Stations from the List
When the shore station phonebook is selected, the oldest MMSI number
or nickname flashes on the dot matrix display.
1. Press the SQ UP/DOWN key to scroll through the registered stations
until the station to be deleted is displayed.
2. Press the ENT key; the message DEL? Y is displayed.
3. Press the ENT key to process the deletion and exit the Menu operation.
To exit without deleting, press the SQ UP/DOWN key until DEL? N
is displayed. If the list has no stations entered, the message PHNBOOK
IS EMPTY HOLD DOWN CLR KEY is displayed. Press and hold
the CLR key for 3 seconds to exit Menu mode.
ENT ENT
SQ UP
/DOWN
4.7.3.4 Modifying the MMSI Group Number (GROUP)
This operation modifies the MMSI number to be used in receiving a Group
Digital Selective Call.
1. As described in Section 4.7.3 DSC Operation above, select the DSC
operation GROUP.
2. Press the ENT key to initiate the process. The 7-segment display shows
GrP and the dot matrix display shows ENTRY.
3. Use the SQ UP/DOWN key to alternate between ENTRY or DELETE.
4. Press the ENT key to submit the desired selection.
ENT
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM50
4-51
Operation with Full Function Handset
Entering a Group MMSI Number
To add a Group MMSI number, select ENTRY then press the ENT key.
Use the numeric keys (0 through 9) to input desired group number. The
currently selected location is indicated by a flashing "–" character. Pressing
a numeric key enters that value then advances to the next place. To go
back by 1 digit, press the CLR key.
After the last position has been filled, the message CONT? Y appears.
Press ENT to register the group and exit the Menu operation. To exit
without registering, press SQ UP/DOWN until DEL? N is displayed. Press
the ENT key and operation returns to mode before the Menu operation
began.
ENT
numeric
keypad
ENT
Deleting a Group MMSI Number
Use the SQ UP/DOWN key to select DELETE. To delete the contents
indicated, press the ENT key and the message DEL? Y is displayed. Press
the ENT key to process the deletion and exit the Menu operation. To exit
without deleting, press the SQ UP/DOWN key until DEL? N is displayed.
Press the ENT key and operation returns to the mode before the Menu
operation began.
ENT ENT
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM51
4-52 Operation with Full Function Handset
4.7.4 Setting Operation
This operation sets the function features of the RAY215E: the ATIS ID
number and on/off state, and the MMSI number.
1. Press the FUNC key followed by the MENU key to initiate the Menu
mode. Mn is shown on the 7-segment display and NAVSTAT appears
on the dot matrix display.
2. Press the SQ UP/DOWN key to select SETTING.
3. Press the ENT key. The message SET appears on the 7-segment display.
Pressing the SQ UP/DOWN key alternates between the following:
MY ATIS registers the ATIS ID number
MY MMSI registers the MMSI number
ATIS turns the ATIS function ON or OFF
Note: The ATIS selection only appears if this option has been enabled
by the dealer.
4. Select the desired operation and press the ENT key to submit your
selection.
ENT
4.7.4.1 Setting ATIS ID Number
This operation stores the ATIS number required for the Automatic
Transmission Identification System used in inland waterways of some
European countries. You can request an ATIS number when you apply for
a radio license.
Regulations in some regions may not allow end users to program their
own ATIS number. If this unit was purchased to be used in such a region,
this function will be disabled and the programming must be done by your
Raymarine distributor.
Notes:
•This is a one time operation. Once the ATIS number has been
programmed, you will not be able to change it.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM52
4-53
Operation with Full Function Handset
• The ATIS ID number is a ten digit number, beginning with a “9”. The
MY ATIS set up process has you input only the last 9 digits. The leading
“9” is automatically input for you.
To register the ATIS Number into memory:
1. Select the MY ATIS function as described above in Section 4.7.4
Setting Operation.
2. Press the ENT key. The 7-segment display shows AId and the dot
matrix display scrolls PLEASE PROGRAM ATIS ID.
3. Press ENT. Nine underscore characters appear, which are placeholders
for the last 9 digits of the ATIS number. The first character place to be
input is flashing.
Pressing the following keys initiate the corresponding operation:
KK
KK
K
eyseys
eyseys
eys
ActionAction
ActionAction
Action
0 - 9 keys Changes the flashing numeric value, then advances to the next
digit's place.
ENT key Advances the (flashing) subject item to the next one without
changing the numeric value. Advances to the next screen after
entering the last (ninth) digit.
CLR key Returns to the previous subject item. Pressing and holding for 3
seconds exits the operation and returns to the mode before the
Menu Operation began.
4. Input your ATIS number using the numeric keypad.
5. Press the ENT key. The message ENT - ACCEPT, CLR - EXIT scrolls
across the display.
6. Press the ENT key to submit the number. The message ENTER ATIS
ID AGAIN is displayed.
7. Press ENT. The nine underscore placeholders appear once more.
8. Again input the ATIS number with the numeric keypad.
9. Press ENT to submit. If the second ATIS number you input matches
the first, the message ENT - ACCEPT, CLR - EXIT is again displayed.
Note: If the two ATIS numbers don’t match, the message ATIS ID NOT
MATCH PRESS ENT scrolls across the display. Press ENT to exit the
Menu mode and try again from step 1.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM53
4-54 Operation with Full Function Handset
10.Press ENT to verify. The message ENT - STORE, CLR - EXIT is
displayed.
11. Press ENT one last time to register the ATIS number in memory.
Operation returns to the mode before the Menu operation began.
To exit without making changes at any time, press and hold CLR for 3
seconds.
Flashing
Flashing
Flashing
ENT
ENT
Input last 9 digits of
ATIS number using
numeric keypad
ENT
ENT
ENT
re-enter
ATIS No.
ENT
ENT
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM54
4-55
Operation with Full Function Handset
4.7.4.2 Setting MMSI Number
This operation stores the MMSI number required for DSC
communications, including distress calls. You can request an MMSI
number when you apply for a radio license.
Notes:
• Regulations in some regions may not allow end users to program their
own MMSI number. If this unit was purchased to be used in such a
region, this function will e disabled and the programming must be done
by your Raymarine distributor.
• This is a one time operation. Once the MMSI number has been
programmed, you will not be able to change it.
• Until the MMSI number is programmed, all DSC functionality is disabled.
Pressing the INDV, ALL SHIP, and DISTRESS buttons will only sound
an error alert.
1. Press the FUNC key followed by the MENU key to initiate the Menu
mode. Mn appears on the 7-segment display and NAVSTAT appears
on the dot matrix display.
2. Press the SQ UP/DOWN key to select SETTING.
3. Press the ENT key. The message SET appears on the 7-segment display
and MY MMSI appears on the dot matrix display.
ENT
4. Press the ENT key to submit. MS appears on the 7-segment display. If
the MMSI number has already been saved to the unit, the dot matrix
display scrolls the programmed MMSI number.
If the MMSI number has not yet been saved to the unit, the dot matrix
display scrolls PLEASE PROGRAM MMSI NO.
5. Press ENT. Nine underscore characters appear, which are placeholders
for the 9 digits of the MMSI number. The first character place to be
input is flashing.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM55
4-56 Operation with Full Function Handset
Pressing the following keys initiate the corresponding operation:
KK
KK
K
eyseys
eyseys
eys
ActionAction
ActionAction
Action
0 - 9 keys Changes the flashing numeric value, then advances to the
next digit's place.
ENT key Advances the (flashing) subject item to the next one
without changing the numeric value. Advances to the next
screen after entering the last (ninth) digit.
CLR key Returns to the previous subject item. Pressing and holding
for 3 seconds exits the operation and returns to the mode
before the operation began.
6. Input your MMSI number using the numeric keypad.
7. Press the ENT key. The message ENT - ACCEPT, CLR - EXIT scrolls
across the display.
8. Press the ENT key to submit the number. The message ENTER MMSI
NO. AGAIN is displayed.
9. Press ENT. The nine underscore placeholders appear once more.
10.Again input the MMSI number with the numeric keypad.
11. Press ENT to submit. If the second MMSI number you input matches
the first, the message ENT - ACCEPT, CLR - EXIT is again displayed.
Note: If the two MMSI numbers don’t match, the message MMSI NO.
NOT MATCH PRESS ENT scrolls across the display. Press ENT to exit
the Menu mode and try again from step 1.
12. Press ENT to verify. The message ENT - STORE, CLR - EXIT is
displayed.
13. Press ENT one last time to register the MMSI number in memory.
Operation returns to the mode before the Menu mode began.
To exit without making changes at any time, press and hold CLR for 3
seconds.
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM56
4-57
Operation with Full Function Handset
Flashing
Flashing
Flashing
ENT
ENT
Input MMSI number
using numeric keypad
ENT
ENT
ENT
re-enter
MMSI No.
ENT
ENT
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM57
4-58 Operation with Full Function Handset
4.7.4.3 ATIS Set Up
This operation determines whether to effect ID transmission of ATIS after
the PTT switch is released.
To set the ATIS function:
1. Per the description in Section 4.7.4 Setting Operation above, select
ATIS.
2. Press the ENT key. The message ATS is shown on the 7-segment
display and ATIS OFF appears on the dot matrix.
3. Press the SQ UP/DOWN key to toggle between ATIS ON and ATIS
OFF.
4. After selecting the desired operation, press the ENT key.
5. If the setting is acceptable, press the ENT key to confirm. The message
CONT? Y is displayed.
6. Press the ENT key to register the setting. When ATIS is ON, the ATIS
indicator is illuminated on the LCD.
To exit without making changes, press the SQ UP/DOWN key until DEL?
N is displayed. Press the ENT key and operation returns to the mode
before the Menu operation began.
ENT ENT
RAY215_EURO Sect4.p65 2/14/2002, 6:29 PM58
5-1
Maintenance
Section 5 Maintenance
5.1 How to Contact Raymarine
The RAY215E is designed to provide long periods of trouble-free
operation. It is recognized, however, that environmental and other factors
may result in a need for occasional service.
In Europe
In Europe, Raymarine support, service and accessories may be obtained
from your authorized dealer, or contact:
Raymarine Limited
Anchorage Park
Portsmouth, Hampshire
England PO3 5TD
Tel +44 (0) 23 9269 3611
Fax +44 (0) 23 9269 4642
Technical Support Tel +44 (0) 23 9269 3611
Fax +44 (0) 23 9269 4642
The Technical Services Department handles inquiries concerning
installation, operation, fault diagnosis and repair.
Accessories and Parts
Raymarine accessory items and parts are available through your authorized
Raymarine dealer. Please refer to the lists of component part numbers and
optional accessories in Section 2.2.1 of this handbook and have the
Raymarine part number ready when speaking with your dealer. If you are
uncertain about what item to choose for your Raymarine unit, please
contact our Customer Services Department prior to placing your order.
In the US
Technical Support 1-800-539-5539 ext. 2444, or
1-603-881-5200 ext. 2444
You can reach our Technical Support Department Monday to Friday 4:00
AM to 6:00 PM Eastern Standard Time. Our Technical Support Specialists
are available to answer installation, operation, and troubleshooting
questions about your Raymarine unit.
Accessories and Parts 1-800-539-5539 ext. 2333, or
1-603-881-5200 ext. 2333
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM1
5-2 Maintenance
Many Raymarine accessory items and parts are available through your
authorized Raymarine dealer. However if you are in need of an item not
available through your retailer feel free to contact our Customer Service
department Monday to Friday 8:15 AM to 5:00 PM Eastern Standard
Time. If you are uncertain about what item to choose for your Raymarine
unit please contact our Technical Support Department Prior to placing
your order at 1-800-539-5539 ext. 2065.
In the unlikely event your Raymarine unit should develop a problem please
contact the Raymarine dealer from where the unit was purchased. Your
Raymarine dealer is best equipped to handle your service needs.
Service may also obtained by returning your unit to Raymarine's Product
Repair Center at the address below.
Raymarine, Inc.
Product Repair Center
22 Cotton Road, Unit D
Nashua, NH 03063-4219
On the Internet
You can also reach us on the Raymarine World Wide Web site:
www.raymarine.com
Navigate to the Customer Support page, which provides links for:
• Finding Factory Service locations and Authorized Dealers near you
• Accessing handbooks in Adobe Acrobat format
• Searching questions and answers in our solution database by product,
category, keywords, or phrases
• Submitting a question to our technical support staff, who reply to you
by e-mail
• Logging in to check the status of your questions, modify your answer
update notifications, or update your personal profile
Questions can be sent directly to our Technical Support Department on
the Customer Support page by clicking Ask Raymarine.
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM2
5-3
Maintenance
5.2 Preventative Maintenance
The RAY215E has been constructed to be virtually maintenance free.
Your attention to a few basic points should assure many years of service.
1. Although the unit is waterproof, always keep the unit as dry as possible.
2. Clean the exterior of the unit with a tissue or soft non-abrasive cloth.
CAUTION
Do not use solvents or other chemicals for cleaning this equipment.
3. Inspect the radio case and antenna for any physical damage.
5.3 Specifications
5.3.1 Transmitter
Channels All available US and International VHF Marine
band
Frequency Stability +/- 10PPM (+/- 0.001%)
(-20 °C to +50 °C)
Frequency Range 156.025 to 157.425MHz
Channel Spacing 25 kHz Increments
Power Output 25 Watts switchable to 1 Watt into 50 Ohms at
13.6 VDC
Modulation Frequency modulated 16F3
(+/-4.5kHz at 1000Hz)
Modulation Audio Response
Shall not vary +1/-3 dB from true 6 dB pre-
emphasis from 300 to 2500Hz, reference 1000Hz.
Audio frequencies 3-20 kHz shall be attenuated
(at 1 kHz by 60 log f/3 dB. Above 20kHz by 50dB)
FM Hum & Noise level
Less than -40dB below audio
Audio Distortion Less than 10% at 1kHz for 3kHz deviation
Spurious & Harmonic Attenuated at least 43+10log Po (below rated
radiated carrier Emissions power) per FCC Rules
Part 2 & 80
Antenna Impedance 50 Ohm
Transmitter Protection Shall survive open or short circuit of antenna
system without damage (10 min. test)
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM3
5-4 Maintenance
5.3.2 Receiver
Channels All available US and International VHF Marine
Band
Frequency Range 156.025 to 163.275 MHz in 25 kHz increments
Frequency Stability +/- 10 PPM (+/- 0.001%) from -20 °C to +50 °C
Usable Sensitivity 0.25µV @ 12dB SINAD
Threshold 1.0µ full squelch
Adjacent Channel Rejection
70dB
Spurious Image Rejection
70dB
Intermodulation Rejection
70dB
Audio Output 2 Watts or more at 10% or less distortion into 4
Ohm load (internal)
Hum & Noise in Audio
Less than -40dB
5.3.3 Operating Requirement
Input Voltage 13.6 VDC +/- 15% (11.6 to 15.6 VDC)
Current Required Typical 6 amp at 25 Watts
Transmit Typical 2 amp at 1 Watt
Operating Temperature -20 °C to +50 °C
Duty Cycle Continuous, 80% receive, 20% transmit
(max 10 min, @25 °C)
Humidity 100% at 50 °C for 8 hours
5.3.4 Radio Dimensions
Base Station Transceiver
Height 80 mm (3.15 inches)
Width 195 mm (7.68 inches)
Depth 170 mm (6.70 inches)
Weight Approx. 1.0 kg (2.2 lbs)
Minimum Function Handset
Height 173 mm (6.8 inches)
Width 57 mm (2.25 inches)
Depth 28 mm (1.1 inches)
Weight Approx. 138 g (0.30 lbs)
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM4
5-5
Maintenance
Optional Full Function Handset (FFHS)
Height 173 mm (6.81 inches)
Width 57 mm (2.25 inches)
Depth 28 mm (1.1 inches )
Weight Approx. 138 g (0.30 lbs)
Optional FFHS Cradle
Height 50 mm (1.97 inches )
Width 64 mm (2.52 inches)
Length 102.1 mm (4.02 inches)
Weight Approx. 70 g (0.15 lbs) (without cables)
Optional FFHS External Speaker
Height 114 mm (4.48 inches)
Width 110 mm (4.33 inches)
Depth 40 mm (1.57 inches)
Weight Approx. 340 g (0.75 lbs)
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM5
5-6 Maintenance
RAY215_EURO Sect5.p65 2/14/2002, 4:12 PM6
5-7
Maintenance
5.4 Drawings
Assembly Drawing
5-8
Maintenance
Block Diagram
RF PCB
5-9
Maintenance
Control PCB
5-10
Maintenance
Front PCB Microphone PCB
6-1
Appendix
International ModeInternational Mode
International ModeInternational Mode
International Mode
Channel Frequency (MHz)
Number TX RX
01 156.050 160.650 Public Correspondence (Marine Operator) Hi, Lo
02 156.100 160.700 Public Correspondence (Marine Operator) Hi, Lo
03 156.150 160.750 Public Correspondence (Marine Operator) Hi, Lo
04 156.200 160.800 Public Correspondence (Marine Operator) Hi, Lo
05 156.250 160.850 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
06 156.300 156.300 Intership Safety Hi, Lo
07 156.350 160.950 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
08 156.400 156.400 Intership Hi, Lo
09 156.450 156.450 Intership, Port Operations, Ship Movement Hi, Lo
10 156.500 156.500 Intership Hi, Lo
11 156.550 156.550 Port Operations, Ship Movement Hi, Lo
12 156.600 156.600 Port Operations, Ship Movement Hi, Lo
13 156.650 156.650 Intership Navigation, Safety Hi, Lo
14 156.700 156.700 Port Operations, Ship Movement Hi, Lo
15
1 1
1 1
1
156.750 156.750 On Board Communications, Intership Lo Only
16 156.800 156.800 International Distress, Safety Hi, Lo
17
1 1
1 1
1
156.850 156.850 On Board Communications, Intership Lo Only
18 156.900 161.500 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
19 156.950 161.550 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
20 157.000 161.600 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
21 157.050 161.650 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
22 157.100 161.700 Public Correspondence (Marine Operator), Hi, Lo
Port Operations, Ship Movement
Type of Traffic
TX
Power
Section 6 Frequency Tables
International Mode
Note: International VHF frequency usage varies from country to country. Ensure
you are familiar with the channel requirements of the country where you are boating
before using any VHF transceiver.
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM1
6-2 Appendix
Channel Frequency (MHz)
Number TX RX
23 157.150 161.750 Public Correspondence (Marine Operator) Hi, Lo
24 157.200 161.800 Public Correspondence (Marine Operator) Hi, Lo
25 157.250 161.850 Public Correspondence (Marine Operator) Hi, Lo
26 157.300 161.900 Public Correspondence (Marine Operator) Hi, Lo
27 157.350 161.950 Public Correspondence (Marine Operator) Hi, Lo
28 157.400 162.000 Public Correspondence (Marine Operator) Hi, Lo
60 156.025 160.625 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
61 156.075 160.675 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
62 156.125 160.725 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
63 156.175 160.775 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
64 156.225 160.825 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
65 156.275 160.875 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
66 156.325 160.925 Public Correspondence (Marine Operator) Hi, Lo
Port Operations, Ship Movement
67 156.375 156.375 Intership, Port Operations Hi, Lo
68 156.425 156.425 Port Operations, Ship Movement Hi, Lo
69 156.475 156.475 Intership, Port Operations, Ship Movement Hi, Lo
70
2 2
2 2
2
— — DSC Communications Only —
71 156.575 156.575 Port Operations, Ship Movement Hi, Lo
72 156.625 156.625 Intership, Port Operations, Ship Movement Hi, Lo
73 156.675 156.675 Intership, Port Operations, Ship Movement Hi, Lo
74 156.725 156.725 Port Operations, Ship Movement Hi, Lo
77 156.875 156.875 Intership Hi, Lo
78 156.925 161.525 Public Correspondence, Port Operations Hi, Lo
79 156.975 161.575 Public Correspondence, Port Operations Hi, Lo
80 157.025 161.625 Public Correspondence, Port Operations Hi, Lo
81 157.075 161.675 Public Correspondence, Port Operations Hi, Lo
82 157.125 161.725 Public Correspondence, Port Operations Hi, Lo
83 157.175 161.775 Public Correspondence, Port Operations Hi, Lo
84 157.225 161.825 Public Correspondence, Port Operations Hi, Lo
85 157.275 161.875 Public Correspondence, Port Operations Hi, Lo
86 157.325 161.925 Public Correspondence, Port Operations Hi, Lo
Type of Traffic
TX
Power
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM2
6-3
Appendix
Notes:
1. For channels 15 and 17, output power is fixed at 1 watt only. Transmission at
high power is not permitted.
2. Channel 70 is used for Digital Selective Calling (DSC) only and is not available
for voice transmissions. Channel 70 does not appear on the display.
Important Notice
The International frequency mode is not legal for use while operating in U.S. waters.
The TX/RX frequencies available in International frequency mode were agreed upon
by the attending countries at the 1968 ITU-International Telecommunication Union
meeting in Geneva, and are legal for use in International waters only.
Type of Traffic
TX
Power
Channel Frequency (MHz)
Number TX RX
87A 157.375 157.375 Public Correspondence, Port Operations Hi, Lo
88A 157.425 157.425 Public Correspondence, Port Operations Hi, Lo
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM3
6-4 Appendix
US ModeUS Mode
US ModeUS Mode
US Mode
Channel Frequency (MHz)
Number TX RX
01A 156.050 156.050 Port Operations and Commercial, Hi, Lo
VTS in selected areas
03A 156.150 156.150 US Government and Coast Guard Hi, Lo
05A 156.250 156.250 Port Operations, VTS in selected areas Hi, Lo
06 156.300 156.300 Intership Safety Hi, Lo
07A 156.350 156.350 Commercial Hi, Lo
08 156.400 156.400 Commercial (Intership only) Hi, Lo
09 156.450 156.450 Boater Calling,
Commercial and non-Commercial Hi, Lo
10 156.500 156.500 Commercial Hi, Lo
11 156.550 156.550 Commercial, VTS in selected areas Hi, Lo
12 156.600 156.600 Port Operations, VTS in selected areas Hi, Lo
13
1 1
1 1
1
156.650 156.650 Intership Navigational Safety
(Bridge to Bridge) Lo
14 156.700 156.700 Port Operations, VTS in selected areas Hi, Lo
15
2 2
2 2
2
— 156.750 Environmental (Receive only) —
16 156.800 156.800 International Distress, Safety, and Calling Hi, Lo
17
3 3
3 3
3
156.850 156.850 State Controlled Lo only
18A 156.900 156.900 Commercial Hi, Lo
19A 156.950 156.950 Commercial Hi, Lo
20A 157.000 157.000 Port Operations Hi, Lo
21A 157.050 157.050 Coast Guard only Hi, Lo
22A 157.100 157.100 Coast Guard Liaison and Maritime Safety Hi, Lo
Info. Broadcasts announced on CH 16.
23A 157.150 157.150 Coast Guard only Hi, Lo
24 157.200 161.800 Public Correspondence (Marine Operator) Hi, Lo
25 157.250 161.850 Public Correspondence (Marine Operator) Hi, Lo
26 157.300 161.900 Public Correspondence (Marine Operator) Hi, Lo
27 157.350 161.950 Public Correspondence (Marine Operator) Hi, Lo
28 157.400 162.000 Public Correspondence (Marine Operator) Hi, Lo
61A 156.075 156.075 US Government and Canadian Coast Guard Hi, Lo
63A 156.175 156.175 Port Operations and Commercial. Hi, Lo
VTS in selected areas.
64A 156.225 156.225 US Government Hi, Lo
65A 156.275 156.275 Port Operations Hi, Lo
US Mode Frequency Table
Type of Traffic
TX
Power
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM4
6-5
Appendix
Notes:
1. For channels 13 and 67, output power is fixed at 1 watt (low power) by regulation.
In an emergency, you can override to high power by pressing and holding PTT
and then pressing the MON/1/25 key on the base station. Output power is increased
to 25 watts while both keys are pressed. After MON/1/25 is released, power returns
to 1 watt.
2. Channel 15 is receive only. Transmission is not permitted.
3. For channels 17 and 77, output power is fixed at 1 watt only. Transmission at high
power is not permitted.
4. Channel 70 is used for Digital Selective Calling (DSC) only and is not available
for voice transmissions. Channel 70 does not appear on the display.
Important Notice
Channels 3A, 21A, 23A, 61A, 64A, 81A, 82A, and 83A (shaded) are not for use by
the general public in U.S. waters. These frequencies may be used only under
authorization by the U.S. Coast Guard or under private land mobile license.
Type of Traffic
TX
Power
Channel Frequency (MHz)
Number TX RX
66A 156.325 156.325 Port Operations Hi, Lo
67
1 1
1 1
1
156.375 156.375 Commercial, Bridge-to-Bridge (Intership) Lo only
68 156.425 156.425 Non-Commercial Hi, Lo
69 156.475 156.475 Non-Commercial Hi, Lo
70
4 4
4 4
4
——DSC Communications Only —
71 156.575 156.575 Non-Commercial Hi, Lo
72 156.625 156.625 Non-Commercial (Intership Only) Hi, Lo
73 156.675 156.675 Port Operations Hi, Lo
74 156.725 156.725 Port Operations Hi, Lo
77
3 3
3 3
3
156.875 156.875 Port Operations (Intership Only) Lo only
78A 156.925 156.925 Non-Commercial Hi, Lo
79A 156.975 156.975 Commercial Hi, Lo
80A 157.025 157.025 Commercial Hi, Lo
81A 157.075 157.075 US Government Only: Environmental Hi, Lo
Protection Operations
82A 157.125 157.125 US Government Only Hi, Lo
83A 157.175 157.175 US Coast Guard Only Hi, Lo
84 157.225 161.825 Public Correspondence (Marine Operator) Hi, Lo
85 157.275 161.875 Public Correspondence (Marine Operator) Hi, Lo
86 157.325 161.925 Public Correspondence (Marine Operator) Hi, Lo
87 157.375 161.975 Public Correspondence (Marine Operator) Hi, Lo
88A 157.425 157.425 Commercial (Intership Only) Hi, Lo
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM5
6-6 Appendix
Weather Channels and Frequencies
CH RX Frequency Type of Traffic Transmission Type
1 162.550 Weather Receive only
2 162.400 Weather Receive only
3 162.475 Weather Receive only
4 162.425 Weather Receive only
5 162.450 Weather Receive only
6 162.500 Weather Receive only
7 162.525 Weather Receive only
8 161.650 Weather Receive only
9 161.775 Weather Receive only
0 163.275 Weather Receive only
RAY215_EURO Sect6.p65 2/14/2002, 4:50 PM6
… 124 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Raymarine Ray 215E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Raymarine Ray 215E in the language / languages: English as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Raymarine Ray 215E

Raymarine Ray 215E Usermanual and installation guide - German - 135 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info