469999

Raymarine Radome Scanners Manual

13
Zoom out
Zoom in
Previous page
1/30
Next page
Installation 9
Cable requirements
You need to consider the following points before installing the system
cables:
• You need to connect the scanner to the display unit and power. The
cable required will depend on the display unit and scanner type.
• All cables should be adequately clamped and protected from physical
damage and exposure to heat - avoid running cables through bilges or
doorways, or close to moving or hot objects.
• Acute bends must be avoided.
• Where a cable passes through an exposed bulkhead or deckhead, a
watertight gland or swan neck tube should be used.
• Avoid cutting and rejoining cables. If this cannot be avoided refer to
Extending the power cable on page -11.
Scanner cables
A radome scanner connected to a C or E-Series display receives power via
the display unit.
Running the cable to the scanner
DO NOT pull the cable through bulkheads using a cord
attached to the connector. This could damage the
connections.
The cable entrance is at the rear of the scanner unit. If the unit is mounted
on a hollow mast, the cable may be run inside the mast and fed though the
unit’s cable entrance. Make sure that the cable does not chafe where it
enters and exits the mast.
To minimize electrical interference try to avoid running radar cables near
other on board electrical equipment. It is also good practice to avoid
running radar cables in parallel with power cables.
Inter-unit cables
The inter-unit cable, illustrated below, is fitted with an 8-way plug and
power cores (covered with a clear protective sleeve) for connecting to the
scanner.
The length of the cable supplied should be sufficient to complete the cable
run on most small boats. For longer runs, additional or replacement cables
are available. These cables have four power cores to minimize voltage
drops over the longer cable run.
Optional cable lengths available are:
• Part No. M92668 - 15 m heavy extension cable.
• Part No. M92669 - 25 m heavy replacement cable.
The maximum inter-unit cable length is limited by the minimum supply
voltage, the scanner type (18” or 24 “radome), and the cable type (2 or 4
power cores).
For boats with 12 V DC power systems details of recommended cable(s) for
different run lengths can be found in Extending the power cable on
page -11.
Boats with 24 V DC power systems can use any combination of inter-unit
cables.
To display or extension
(power supplied via display unit)
To Radome Scanner
D8858_1
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Raymarine Radome Scanners at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Raymarine Radome Scanners in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info