672984
20
Zoom out
Zoom in
Previous page
1/60
Next page
20 A-Series display - Installation instructions
3.1 General wiring instructions
Cable types and length
Follow the guidelines given in this section to determine appropri-
ate cable types and length.
Unless otherwise stated use only standard cables of the correct
type, supplied by Raymarine.
Ensure that any non-Raymarine cables are of the correct quality
and gauge. For example, longer power cable runs may require
larger wire gauges to minimize any voltage drop in a cable.
Routing cables
No acute bends. Minimum bend radius of 100mm.
Protect all cables from physical damage and exposure to heat.
Use trunking or conduit where possible. Avoid running cables
through bilges or doorways, or close to moving or hot objects.
Secure cables in place using tie-wraps or lacing twine. Coil any
extra cable and tie it out of the way.
Use a watertight feed-through wherever a cable passes through
an exposed bulkhead or deckhead.
Do not pull cables through a bulkhead or deckhead using a cord
attached to the connector. This could damage the connections.
You should always route data cables:
as far apart from other equipment and cables as possible,
as far away from high current carrying AC and DC power lines
as possible,
as far away from antennas as possible.
Strain relief
Ensure adequate strain relief is provided. Protect connectors
from strain and ensure they will not pull out under extreme sea
conditions.
Circuit isolation
For installations using both AC and DC current:
Always use isolating transformers or a separate power-inverter
to run PC’s, processors, displays and other sensitive electronic
instruments or devices.
Always use an isolating transformer with Weather FAX audio
cables.
Always use and RS232/NMEA converter with optical isolation on
the signal lines.
Always make sure that PC’s or other sensitive electronic devices
have a dedicated power circuit.
Cable shielding
Ensure that all data cables are properly shielded that the cable
shielding is intact (e.g. hasn’t been scraped off by being squeezed
through a tight area).
D10596-1
Minimum bend of cable
100 mm (4 in) radius
Minimum bend
200 mm (8 in)
diameter
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Raymarine A50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Raymarine A50 in the language / languages: English as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Raymarine A50

Raymarine A50 User Manual - English - 156 pages

Raymarine A50 Installation Guide - German - 60 pages

Raymarine A50 User Manual - German - 162 pages

Raymarine A50 Installation Guide - Dutch - 62 pages

Raymarine A50 User Manual - Dutch - 166 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info