661002
87
Zoom out
Zoom in
Previous page
1/198
Next page
en-85
11 PROBLEM SOLVING
.1 PROBLEM SOLVING GENERAL ______________________________________________________
Symptoms Possible Causes Action
Engine will not start
Glow plug has not timed out Reset ignition switch and allow glow plug to time out before
cranking engine.
Battery low on charge or
defective.
Inspect condition of battery and battery connections.
Fuel tank empty or fuel
contaminated.
Fill tank with fresh fuel. Change filter, Bleed air from lines.
Blown fuse. Replace Fuse.
Defective starter relay. Test and replace relay if necessary.
Mow switch set to cut. Set mow switch to off.
Transport pedal not in neutral. Remove foot from pedal, cheek pedal returns to the neutral
position.
Engine hard to start
or runs poorly.
Fuel tank empty or fuel
contaminated.
Fill tank with fresh fuel. Change filter, Bleed air from lines.
Air Cleaner blocked or dirty. Check air cleaner, replace as neccesary.
Injectors, fuel pump. Consult engine manual.
Other Engine Problem. Consult engine troubleshooting guide.
Engine Stops
Fuel tank empty. Fill with fresh fuel and bleed lines.
Interlocks not set before leaving
operators seat.
Ensure Parking Brake is on & Mow switch is in the off position.
Engine Overheating
Coolant level low. Inspect and add 50/50antifreeze solution if required
Radiator air intake restricted. Clean wire mesh guard at radiator.
Waterpump/alternator belt or fan
belt loose or broken.
Inspect waterpump/alternator belt and fan belt. Tighten if
neccesary.
Battery not holding
charge. Battery light
on
Loose or corroded battery
terminals.
Inspect terminals, clean and tighten as required.
Low electrolyte level in battery. Refill battery with distilled water.
Alternator belt loose or broken. Inspect waterpump/alternator belt. Tighten if neccesary.
Alternator defective. See engine manual.
Decks cut unevenly
Poor quality of cut.
Cutting blades are worn. Replace blades.
Engine speed too low. Check engine speed, run engine at full throttle.
Cutter motors worn. Check case drain leakage & flow check cutting circuit.
Ground speed to high. Set work speed stop.
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ransomes Highway 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ransomes Highway 3 in the language / languages: English, Dutch as an attachment in your email.

The manual is 27,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info