713880

Quickie Xenon 2 FF Manual

21
Zoom out
Zoom in
Previous page
1/92
Next page
ENGLISH
XENON 2 FF 21 Rev.4.0
6.4 Seating
Seat Sling
The seat sling can be adjusted for tension by using several straps. To
adjust the tension of the seat sling all straps have to be open. By pulling
the straps the tension of the seat sling will be tightened, (Fig.6.4.1).
NOTE: If the tension is too high, the cross brace will not be able to slide
into the saddle.
Adjusting the seat height:
Lightweight adapter
To change the seat height;
• Remove the rubber bungs, (3) situated in the groove to the rear of the
axle stem.
• Release the Allen screws (1) with an Allen key. Position axle bracket (2)
on the axle stem (4) according to the desired seat height (Fig.6.4.2).
• In order to obtain the lowest possible seat height, the axle bracket can
be mounted upside down.
• Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
• Refit the rubber bungs.
Standard adapter
To change the seat height:
• Remove the rubber bungs, (3) situated in the groove to the rear of the
axle stem.
• Release the Allen screws (1) with an Allen key. Position axle bracket (2)
on the axle stem (4) according to the desired seat height (Fig.6.4.3).
• Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
• Refit the rubber bungs.
NOTE:
• An adjustment to the castor angle may be necessary when adjusting
the rear seat height.
• In case the axle adapter was moved or removed whilst adjusting
the seat height, wheel alignment and wheelbase width needs to
be checked and if necessary, adjusted (please refer to the "Wheel
Alignment" section).
CAUTION!
• Some of the screws used during manufacturing are coated with
thread-locking fluid (blue dot on the thread) and can only be adjusted
up to 3 times before they need to be replaced by new thread-locking
screws. Alternatively, the screws can be re-mounted using Loctite™
243 thread locker.
• Loctite™ 243 thread locker MUST be used for re-mounting the Allen
screws (1) on the axle-adapter.
Fig.6.4.1
Fig.6.4.3
2
3
1
4
Fig.6.4.2
3
1
2
4
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Xenon 2 FF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Xenon 2 FF in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info