Manual Quickie Life T (page 23 of 124) (English, Dutch, Danish, French, Italian)

713888

Zoom out

Zoom in

1/124

ENGLISH

Life T Rev.E

Step tubes are used by attendants to push a wheelchair over an

obstacle. Simply step on the tube to push a wheelchair, for

example, over a kerb or step, (Fig. 6.9).

CAUTION!

Sunrise Medical strongly

reccommends the use of a step

tube on any model where

attendant use is the predominant

intended use. Damage to the

backposts may occur if you

constantly use the backpost

without a step tube, as a lever to

pull back on to tip the wheelchair.

Step Tubes

Fig. 6.9

Footplates (Fig. 6.10)

There are two types of footplates:

platform and divided. They can be

flipped up to facilitate getting in and

get ting out of your wheelchair.

Lower leg lengths

By removing the setscrews (1),

the footrest can be adjusted to fit

any lower leg length. Remove

setscrews, set tubing with footrest in the desired position, and

reinsert and tighten the setscrews (see the page on torque).

Make sure that the composite plastic pad is in the proper

position under the setscrew. A minimum interval of 2.5

centimeters from the ground should always be maintained.

The screws used are fitted with threadlock at the factory and

can be adjusted 5 x after fitting. After that they should be

replaced or alternatively re-secured with threadlock to medium

tightness.

Footplates

Width Adjustment of Aluminium

Footrests

If the footrest width needs to be

adjusted, please undo the screw

(1), set the desired width, by

positioning 1, 2 or 3 spacers (2)

from outer to the inner side and

then refit the screws, (Fig. 6.11).

Angle Adjustment of Aluminium Footboard

The footboard can be flipped up to make it easier to transfer to

and from the chair, (Fig. 6.13 - 6.15).

This can be adjusted to alter the angle to the ground.

Tighten screw (1) on the outside. By loosening the clips (2) the

footboard can be moved to three positions both forwards and

backwards. To do this, the footboard must be flipped up. Make

sure that after any adjustment work, all screws are tightened

correctly (see the page on torque). Ensure that you maintain the

minimum gap to the floor (25mm).

Angle-Adjustment of Composite

Footrest (Fig. 6.16).

This can be adjusted to alter the

angle to the ground. Release

screw, pull it inwards, set the

desired angle and then push it on.

After making the adjustment,

re-tighten the screw. Make sure

that after any adjustment work, all

screws are tightened correctly (see

the page on torque).

Ensure that you maintain the

minimum gap to the floor (25mm) (Fig. 6.15).

Hanger and Latch

The legrests can be swung inwards under the seat sling or

outwards.

When fitting the legrests, the footrests must be pointing inwards

or outwards. Then rotate the legrest inwards, until it locks into

place. To remove, pull the lever (1), swing the hanger inwards

or outwards and then lift the legrest out. Make sure that the

legrest is locked into place correctly (Fig. 6.17 - 6.18).

Fig. 6.16

Fig. 6.13

Fig. 6.14

Fig. 6.15

>25mm

Fig. 6.11

Fig. 6.10

Footboard lock

The footplate locks in automatically

when ipped down. To ip it up the

release knob (1) must be pulled

(Fig. 6.12). To keep the unlocked

position turn knob 1 when it is

pulled.

WARNING:

Always make sure to unlock the system to get full functionality!

Fig. 6.12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Life T in the language / languages: English, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 4,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quickie Life T Manual

Product: