Manual Quickie HeliX 2 Comfort (page 15 of 188) (English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

713891

Zoom out

Zoom in

1/188

15HeliX

ENGLISH

ADJUSTING THE CALF PAD

(Fig 19).

The calf pad can be adjusted as

follows:

Height: Open bolt (4) and move the

clamping piece to the desired

position. By rotating the clamping

piece also the angle can be

adjusted.

Depth: Open bolt (5) and move the

calf pad into the desired position.

Width: Open bolt (5) and position the

spacers (6) behind the pad, to get

the desired position.

WARNING!

• Keep hands clear of the adjustable mechanism between the

frame and the movable parts of the foot rest, while elevating or

lowering the footrest.

• Always make sure that the fasteners are secure.

• The foot rests must not be used to lift or to carry the

wheelchair.

• Risk of trapping fingers! When moving the foot rest up or

down, do not put your fingers in the adjusting mechanism

between the moving parts of the foot rest.

AMPUTEE SUPPORT

(Fig.20).

The Amputee Support can be

adjusted in every direction as

required.

CASTORS, CASTOR PLATES, FORKS

The wheelchair may veer slightly to the right or left, or the castors

may wobble. This may be caused by the following:

• Forward and/or reverse wheel motion has not been set properly.

• The castor angle has not been set correctly.

• Castor and/or rear wheel air pressure is incorrect; the wheels do

not turn smoothly.

The wheelchair will not move in a straight line if the castors have

not been properly adjusted. Castors should always be adjusted by

an authorised dealer. The wheel locks must be checked every time

the rear wheel position has been altered.

The seat height is determined by the

castor and rear wheel position. The

seat height can be adjusted by

altering the position of the rear

wheels and the castors and by using

spacers, (Fig.21).

CAUTION!

After adjusting the seat height, all

screws must be re-tightened and the

wheel lock must be readjusted.

FIG. 19

FIG. 20

Options - Castors

Options - Castor Adapter

NOTE:

You can change the angle of the castor axle by altering the position

of the castor/rear wheel. This should always be approx. 90°.

ADJUSTING THE CASTOR AXLE ANGLE:

Release the screws (1), pull the castor adaptor outwards, set a 90°

angle and then re-tighten the screws (Fig. 22-24).

CAUTION!

The castor axle angle must be set the same on both sides (check by

marking).

HORIZONTAL AXLE POSITION

The axle plate can be adjusted

forwards to give greater

manoeuvrability or to the rear to give

greater stability (Fig. 22).

The larger the wheelbase, the greater

the security against your wheelchair

tipping over.

0° / 3° CAMBER:

By rotating the axle adapter by 180° the camber can be set to 3° or

0°.

NOTE:

When making this adjustment, the wheelbase must also be

re-adjusted afterwards.

CAUTION!

Wheel locks must be adjusted to suit the new position!

Fig. 21

Fig. 24

Fig. 22

Fig. 23

90°

Height-adjustable backrest

The backrest height can be

adjusted from 35 - 50 cm

(depending on the backrest

position). Release the bolts

(1)+(2), and push the backrest

tube to the desired position.

Tighten up the bolts again

(Fig. 25).

Options - Backrest

Fig. 25

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quickie HeliX 2 Comfort in the language / languages: English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quickie HeliX 2 Comfort Manual

Product: