721960
17
Zoom out
Zoom in
Previous page
1/28
Next page
17
Make sure the positioning belt is properly secured to the
power chair and is adjusted for operator comfort before
each use.
Inspect the positioning belt for loose parts or damage,
including tears, worn spots, bent hardware, damaged
latch mechanisms, dirt or debris, before each use of
the power chair. If you discover a problem, contact your
Quantum Rehab Provider for maintenance and repair.
Positioning Belt
Your power chair may be equipped with a positioning belt that
can be adjusted for operator comfort. See figure 16 or 17.
The positioning belt is designed to support the operator so
that he/she does not slide down or forward in the seat. The
positioning belt is not designed for use as a restraining device.
The positioning belt is not designed for use as a seat belt
in a motor vehicle. Anyone traveling in a vehicle should
be properly belted into seats approved by the vehicle
manufacturer. Your power chair is not suitable for use as
a seat in any vehicle with the following exception: The
vehicle must be equipped with a Wheelchair Tie-down
and Occupant Restraint System (WTORS) that has been
installed in accordance with the tie-down manufacturer's
instructions, and is compliant with ANSI/RESNA WC/Vol.
4, Section 18/ISO 10542 standards, and the power chair
must have a transit securement system conforming
to ANSI/RESNA WC/Vol. 4, Section 19/ISO 7176-19
standards. It is essential to use a complete WTORS to
secure the power chair to the vehicle and to provide
the power chair occupant with a properly designed
and tested safety restraint system. A restraint system
with both pelvic and upper-torso belts must be used
to protect the power chair occupant and minimize the
likelihood of injury caused by contact with the vehicle
during a crash or sudden braking.
The positioning belt should be secured at all times.
Never allow the positioning belt to hang or drag on the
floor as it may become entangled.
To install the positioning belt:
1. Remove the rearmost screw that holds the seat hinge to
the seat base on both the left and right seat hinges.
2. Insert the screw through the supplied washer, through
the positioning belt and into the seat base for each side
of the power chair seat.
3. Tighten both screws.
NOTE: If your power chair is equipped with an optional
seating system, please refer to the user manual provided
with the seat for instructions on positioning belt
installation or contact your Quantum Rehab Provider.
To adjust the positioning belt for operator comfort:
1. Once seated, insert the metal tab on one side of the belt
into the plastic housing on the opposite side until you
hear a click.
2. Pull the excess strap attached to the metal tab until it is
secure, but not so tight as to cause discomfort.
To release the positioning belt:
1. Press the push button mechanism on the plastic housing.
COMFORT ADJUSTMENTS
MANDATORY!
WARNING!
Figure 16. Positioning Belt Installation and Adjustment–
Configuration A
Figure 17. Positioning Belt Installation and Adjustment–
Configuration B
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quantum Q4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quantum Q4 in the language / languages: English as an attachment in your email.

The manual is 6,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quantum Q4

Quantum Q4 User Manual - German - 32 pages

Quantum Q4 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info