721958
13
Zoom out
Zoom in
Previous page
1/36
Next page

Initial Assembly
Your power chair may require some assembly either before initial use or after transportation. It may also
require disassembly to make some comfort adjustments. Figure 6 details those parts of the power chair
that are designed to be disassembled and assembled by an end user or by a qualified caregiver before
using the product or making comfort adjustments.
NOTE: If your power chair is equipped with a TB-Flex Seat, a Synergy Seat, or a TRU-Balance® 3
Power Positioning System, refer to the information provided in separate manuals.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power
chair must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may
cause damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock
nuts are available at local hardware stores or through your Quantum Rehab Provider.
Seat Installation
It may be necessary to install the seat either prior to initial operation or after transporting your power
chair. Contour seats are attached to the power base with the Universal Mounting System (UMS). The
UMS consists of universal parts that may be attached to the seat, regardless of seat width or seat
depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions
attach to a pair of trapeze bars that are mounted to the power base. See figure 7.
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of
the seat if they do so.
To install the seat:
1. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 7.
2. Lower the front extrusion onto the front trapeze bar until the seat latches into place.
3. Flip the seat latch safety down.
WARNING! Make sure the seat latch safety is flipped down before using your power chair.
4. Install the controller and route the harness to the back of the power base. See figure 8.
MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the
armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down
points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat
frame, or damaged when passing through doorways.
5. Plug the controller connector into the rear of the power base. See figure 1.
6. Secure the controller harness to the armrest receiver with wire ties. See figure 8.
Assembly
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quantum Aspen at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quantum Aspen in the language / languages: English as an attachment in your email.

The manual is 7,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quantum Aspen

Quantum Aspen User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info