778522
13
Zoom out
Zoom in
Previous page
1/15
Next page
24 25
0.43-0.51mm
Cleaning or replacing the air filter
WARNING!
Never run the engine without the air lter element installed:
1. Loosen the fastener (A) that holds the cover (B).
2. Open the cover and remove the lter (C).
3. To loosen debris, gently tap the lter on a hard surface. If the lter is excessively dirty,
replace with a new lter.
4. Install the air lter.
5. Install the cover tabs (D) into the slots (E).
6. Close the cover and secure with the fastener (A).
Cleaning or replacing the spark plug
1. Once the engine has cooled, pull off the spark plug boot with a twist. Remove the
spark plug using the socket spanner supplied.
2. Clean the plug with a wire brush.
3. Using a feeler gauge, set the gap to 0.51mm.
4. Install the spark plug carefully by hand to avoid cross-threading.
5. After the spark plug is seated, tighten with the spanner to compress the washer.
Adding the oil
Rell with SAE 30 oil or equivalent, i.e. SAE 5W/30, SAE 10W/30). When the dipstick is
rested on the ller pipe, the oil level must be between the min. and max. marks on the
dipstick.
See ‘Filling with engine oil’. Do not overll.
Start the engine and allow it to run briey.
Stop the engine, wait one minute and check the oil level. Top up if necessary.
Replacing the cutting blade
WARNING! USE GLOVES.
Before you remove the grass collection bag, stop the engine and wait until the
blade stops completely.
You will need garden gloves (not provided) and a spanner wrench to remove the
blade.
Always handle the blade with care; sharp edges could cause injury.
NEVER hold the blade directly by hand.
Renew your metal blade after 36 hours of mowing or after 2 years, whichever is sooner,
regardless of condition.
Regularly check your blade. If the cut of your grass is poor, the blade might be blunt.
Damaged blades not only result in a bad cut, they cause excessive vibration and
uneconomical running of the engine. If the blade has worn excessively and become pitted
and blunt, it should be replaced or sharpened.
Note: The blade carrier is designed to break under heavy blade impact to protect the
machine. If this happens, also replace the blade carrier. This can be purchased from
www.gardenservicecentre.co.uk.
To replace the blade, hold the blade and unscrew the blade bolt counterclockwise using a
spanner wrench. Remove the washer and the blade.
Inspect the blade adaptor for any signs of damage.
Fit a new blade, locate the blade on the two studs on the blade ange and then replace the
washer and bolts.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Qualcast QSPP53 - 484348 - XSZ53D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Qualcast QSPP53 - 484348 - XSZ53D in the language / languages: English as an attachment in your email.

The manual is 10.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info