698697

Quadral AURUM A10S Manual

7
Zoom out
Zoom in
Previous page
1/25
Next page
12
EN
13
SPECIFICATIONS
A10S
Input sensitivity for 1W @8ohms -16,3 dBV
Input impedance 47kOhm
Voltage gain 38dB
Maximum input voltage 6V
Volume adjustment range 100dB
Balance adjustment range +/-6dB
Adjustment accuracy 0.1dB
Channel balance <0,05dB
Maximum voltage at speaker output 48V
Minimum speaker impedance 2.5 Ohm
Output power at 8 ohms 100W
Output power at 4 ohms 180W
Frequency response 1Hz-110kHz(-3dB)
Harmonic distortion <0.03%
Signal-to-noise ratio 75dB unweighted
Mains power connection 115V/230V switch
Power consumption in normal mode 15W
Power consumption at max volume 600W
Power consumption in standby mode <0,5W
Inputs 3 RCA
1 Line XLR
2 TosLink
1 SPDIF
1 USB
Speaker outputs 1 pair
Dimensions
Width including wooden sides 453 mm
Height including feet 130 mm
Depth with speaker terminals 345 mm
Weight 13.86Kg
INSTALLING
1. Select the correct voltage required on the back of the unit amplifier that matches the voltage coming
from the mains supply. Use the power cable supplied in the package to connect the equipment up to the
mains supply.
2. Check that the unit is switched off.
3. Connect up the auxiliary units that you want to use to the equipment‘s inputs. (RCA 1-3, TosLink, SPDIF,
USB) right channel = red / left channel = white or the symmetric analog XLR inputs can be used with
any compatible signal source.
(XLR pin assignments: Pin 1= ground; Pin 2 = plus / signal; Pin 3 = minus)
4. The screw terminals at the back are used for the speaker connections.
5. (See back of the equipment: right channel = 1 / left channel = 7). You must also ensure that the plus
and minus connections on the amplifier concur with the plus and minus connections on the speakers in
order to prevent polarity reversal.
6. Now switch your amplifier on.
Switch the mains switch (12) into the ON position on the back. The standby LED on the front will come
on.
7. Now press the multifunction knob (2) on the front or the button (2) on the remote control to start your
equipment.
Note:
As your A10S uses a special power-saving standby circuit, you can always switch on / off during normal
operation using the multifunction knob on the unit or the RC-3 remote control.
The RC-3 remote control makes it easier for you to change your settings.
Mute (button 2)
Balance setting (buttons 14 + 15)
Input settings for all jacks (button 3 + 4)
Example: Input settings
Select the signal source using buttons 11 (-) or 12 (+), then press button 22 (Prog.) and use the volume but-
tons (3 + 4) to set the desired input volume. To save, press button 22 (Prog.) again.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadral AURUM A10S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadral AURUM A10S in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info