815526
26
Zoom out
Zoom in
Previous page
1/40
Next page
26 02/227050-802H
Remove 2 screws on the
outside of hopper in the front
and 2 screws inside the
hopper at the back.
Figure 26.1
Convection Cover
Hook
Hook
Remove 2 screws at each end
Figure 26.2
Wing Nut
Bracket
Disconnect
Wires
Figure 26.3
Figure 26.4
Loosen Wing
Nut to relieve
pressure
Shaded area
inserted in hole in
Feed Tube
Rotate bracket counterclockwise
once pressure is relieved
With bracket in rotated position,
reach behind bracket and remove
and replace Snap Disc
Figure 26.5
B. Snap Disc #2 - Part Number:SRV7000-268
NOTE:CombustionBlowerGasketisalsorequired.Sold
separatelyunderPartNumberSRV240-0812.
NOTE: You may need pliers to start the wing
nut(Figure 26.4).
10. When bracket is loose enough, rotate the
bracket counterclockwise and away from feed
tube(Figure 26.5).
11. Reachbehindbracketandremoveoldsnapdisc.Install
new snap disc and rotate back to original position
ensuringthesnapdiscisinsertedintheholeinthefeed
tube.Tightenthewingnutandre-attachthewirestothe
newsnapdisc.
12. Re-installinreverseorder.Besuretousenewgasket
wheninstallingcombustionblowerhousing.
1. Turn down thermostat, let appliance cool completely
if running. Then unplug appliance before servicing.
Disconnect appliance from venting at the rear
ofappliance.
2. Removebothupperandlowersidecurtainsbyremoving
thesix7/16”nutsontherearoftheappliance.
3. Disconnectthevacuumhoseandwiresfromthevacuum
switch. Disconnect the blue and white wires from the
combustion blower. Remove control box retainer clip.
Removetwoscrewsthatholdthejunctionbox.Setaside
carefully.Disconnecthopperswitch.
4. Remove cast top from appliance. Two fasteners are
locatedoutsidethehopperoneachside.Theothertwo
arelocatedinthehopperalongtheback(Figure 26.1).
Remove the rear screen of the appliance (be sure the
ventisdisconnected)byremovingthesevenscrews.Lift
slightlyupwardsastonotdamagethehopperswitchand
setaside.
5. Removelowerscrewbyremovingvescrews.Layat
onground.
6. Removeconvectioncoverbyremovingthetwoscrews
atthebottom(oneeachside)andslidetotheleft,then
setaside.
7. Remove the ve 7/16” bolts holding the combustion
blowerhousingtotheexhaustplenum.Discardgasket.
(Cleanblowerimpellerandplenumifneeded).
8. Disconnectwiresfromsnapdisc#2(Figure 26.3).
9. Loosen wing nut to relieve the pressure on snap disc
fromthebracket.Theshadedareaof the snap disc is
insertedintoaholeinthefeedtube
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Santa Fe - Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Santa Fe - Pellet in the language / languages: English as an attachment in your email.

The manual is 11.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Santa Fe - Pellet

Quadra-Fire Santa Fe - Pellet User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info