815519
23
Zoom out
Zoom in
Previous page
1/34
Next page
23 7095-803R 12/23
Figure 23.4
Blower
Snap Disc
Five Setting Switch
Switch
Power Cord
Figure 23.3
G. Door Handle
Service Part: SRV7063-014
1. Install washer on door handle shaft.
2. Slide door handle through door.
3. Install additional washer(s) as shown in Figure 23.4.
4. Install key in groove.
5. Align groove in latch cam with key; slide latch cam
over shaft
6. Install locknut but do not over tighten, the handle needs
to move smoothly.
7. Install handle turning in a counter-clockwise motion to
desired location on door handle rod (Figure 23.4).
Locknut
Latch Cam
Spacing
Washers
Door Cross
Section
Square Key
Door Handle Shaft
Fiber Handle
E. Ba󰀪e Board
Service Part: SRV7095-117
1. Remove all ash from the rebox, and extinguish all hot
embers before disposal into a metal container.
2. It is easier to remove both ba󰀪e boards and ceramic
blanket after the tube channel assembly has been
partially disassembled and the right side lowered. Follow
steps 1 through 4 on page 25 for removal of the tube
channel assembly. It is not necessary to completely
remove the tube channel assembly.
3. Once the ba󰀪e protection cover has been removed, pull
the ba󰀪e boards and ceramic blanket forward about
1 inch (25mm) and then overlap the ba󰀪es about 1-2
inches (25-51mm) (Figure 23.1).
4. Slide the tube channel assembly to the left as far as it will
go and lower the right side. Remove the ba󰀪e boards
and ceramic blanket together (Figure 23.2).
5. Re-install in reverse order. Be sure the ba󰀪e boards and
ceramic blanket are in their proper positions (Reference
Correct Ba󰀪e & Blanket Placement on page 19).
Figure 23.1
Baffle Boards Overlapping
Ceramic Blanket
Figure 23.2
The ceramic blanket and both baffle boards
and tube channel assembly can all be
removed at the same time.
F. Wiring Diagram
Service Part: SRV7000-891
Do not over tighten lock nut. The door handle needs to
move smoothly.
CAUTION
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Expedition II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Expedition II in the language / languages: English as an attachment in your email.

The manual is 6.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Expedition II

Quadra-Fire Expedition II User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info