Manual Quadra-Fire Discovery I (page 21 of 32) (English)

815515

Zoom out

Zoom in

1/32

04/237039-804H21

5 Service Part Replacement

A. Glass B. Firebrick

Service Part: SRV7039-007

Replace the rebrick if they become crumbly and/or if there

is a 1/4 inch (6.35mm) gap between the bricks.

Inspect the rebrick after each ash removal.

The rebox is lined with high quality rebrick, which has

exceptional insulating properties. There is no need to use a

grate; simply build a re on the rebox oor. Do not operate

appliance without rebrick.

1. After the coals have completely cooled, remove all old

brick and ash from appliance and vacuum rebox.

2. Remove new brick set from box and lay out to

diagram shown.

3. Lay bottom bricks in appliance.

4. Install rear bricks on the top of the bottom bricks. Slide

top of bricks under clip on back of rebox wall and push

bottom of brick back.

5. Install side bricks. Slide top of brick under clips on side

of rebox and push the bottom of the brick until it is

ush with the side of the appliance.

WARNING

Injury Risk.

• Use only glass specied in manual.

• DO NOT REPLACE with any other

material.

Handle glass assembly with care.

When cleaning glass:

Glass

Assembly

CAUTION

• Avoid striking, scratching or slamming glass.

• Do NOT clean glass when hot.

• Do NOT use abrasive cleaners.

• Use a hard water deposit glass cleaner on white lm.

• Use commercial oven cleaner on heavier deposits.

• Remove all residue of oven cleaner or will

permanently stain glass on next ring.

Refer to maintenance instructions.

Service Part: SRV7000-013

1. Ensure that the re is out and the appliance is cool to

the touch.

2. Protect a table or counter top with padding or towels.

Protect your hands and wear gloves to prevent injury.

3. Remove the door with the broken glass by lifting the

door up and o󰀨 of the hinges.

4. Lay door face down on a table or counter making sure

the handle hangs over the edge so the door lays at, on

a soft surface.

5. Remove the screws from each glass retainer and

remove the glass. (If screws are di󰀩cult to remove,

soak with penetrating oil rst).

6. Center the glass with edges evenly overlapping the

opening in the door, (i.e. same space top and bottom,

left and right sides).

7. Replace the glass retainers. Be careful not to cross

thread the screws.

8. Tighten each retainer just a few turns until each is

secured. Check again for centering of glass in door

frame. Continue to tighten each retainer alternately, a

few turns at a time, until the glass is secure.

NOTE: Replace with 5mm ceramic glass only

Figure 21.1

Figure 21.2 Figure 21.3

2224

1-3/8 in

(35mm)

1-3/4 in

(44mm)

5-1/4 in

(159mm)

7-3/4 in (197mm)

8-1/2 in (216mm)

3 in

(76mm)

7 in (178mm)

Table 21.1

Placement Dimensions Qty

Required

19” x 4.5” x 1.25” 9

25-3/4” x 4.5” x 1.25” 3

38” x 4.5” x 1.25” 2

47-3/4” x 4-1/2 ” x 1.25” w/Angles 1

58-1/2” x 3” x 1.25” w/Angle 1

NOTE: DO NOT OVER TIGHTEN RETAINERS - can

cause glass to break.

9. Replace the door on the appliance.

Quadra-Fire appliances are equipped with ceramic super

heat-resistant glass, which can only be broken by impact

or misuse.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Discovery I in the language / languages: English as an attachment in your email.

The manual is 8.53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Discovery I

Quadra-Fire Discovery I User Manual - French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quadra-Fire Discovery I Manual

Product: