815524

Quadra-Fire Classic Bay 1200 Pellet Manual

24
Zoom out
Zoom in
Previous page
1/40
Next page
24 7027-802M 04/23
Symptom Possible Cause Corrective Action
Feed system fails to start. Out of fuel.
#2 snap disc may be defective.
Vacuum switch not closing. No vacuum.
Feed system jammed or blocked.
Feed spring not turning with feed motor.
Feed motor defective or not plugged in.
Check hopper, ll with fuel.
Replace snap disc. Firebox door must be closed securely.
Check exhaust blower is plugged in and operating.
Check vacuum switch is plugged in. Check vacuum hose is in
good condition, clear and connected at both ends.
Check thermocouple is in good condition and plugged
in properly.
Make sure venting system is clean.
NOTE: High winds blowing into the venting system can
pressurize the rebox causing loss of vacuum.
Empty hopper of fuel. Use a wet/dry vacuum cleaner to remove
remaining fuel, from hopper, including feed tube.
Check feed chute for obstructions.
Loosen 2 screws and jiggle feed assembly.
Check that set screw is tight on feed spring shaft at end of feed
motor.
Check connections on feed motor, replace if defective.
Appliance fails to shut o󰀨. Call light on. Turn thermostat o󰀨.
If call light does not go out, disconnect thermostat wires
from appliance. If call light does go out, thermostat or wires
are defective.
Convection blower fails
to start
#1 snap disc defective.
Blower not plugged in.
Blower is defective.
Control box is defective.
Replace snap disc.
Check that blower is plugged into wire harness.
Replace blower.
Replace control box.
Exhaust blower fails to
start or does not shut o󰀨.
Blower not plugged in.
Blower is clogged with ash.
Blower is defective.
Control box is defective.
Check that blower is plugged into wire harness.
Clean exhaust system.
Replace blower.
Replace control box
Large, lazy ame, orange
color. Black ash on glass.
Dirty appliance.
Poor fuel quality, high ash content.
Fire pot clean-out plate not
completely closed.
Excessive amount of fuel.
Clean appliance, including re pot, heat exchangers and
venting system. Remove stainless steel ba󰀪e from rebox to
clean ash from on top of ba󰀪e. Clean behind rear brick panels.
Change fuel brand to premium.
Check that re pot clean-out plate is fully closed.
Reduce feed rate using feed rate adjustment control rod
located inside hopper.
Nuisance shutdowns. Low ame.
Sawdust buildup in hopper.
Feed motor is reversing.
Defective thermocouple.
Defective control box.
Fire pot more than 1/2 full.
Increase feed by opening feed rate adjustment control rod
located inside hopper.
Clean hopper, see Cleaning The Hopper on page 19.
Check for good connections between feed motor and
wire harness.
Replace thermocouple.
Replace control box.
See High Ash Fuel Content Management on page 22
Appliance calls for heat.
Call light illuminates.
Exhaust blower starts.
No feed or igniter.
Thermocouple is defective or not properly
plugged in.
Defective control box
Check connections on thermocouple or replace if defective.
A ashing yellow light on the control box indicates a problem
with the thermocouple.
Replace control box.
Hopper lid not closed all
the way
Switch or magnet is out of adjustment
(auger will not function)
Close the lid. If that doesn’t work, adjust or replace the switch
or magnet
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Classic Bay 1200 Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Classic Bay 1200 Pellet in the language / languages: English as an attachment in your email.

The manual is 5.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Classic Bay 1200 Pellet

Quadra-Fire Classic Bay 1200 Pellet User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info