815511
23
Zoom out
Zoom in
Previous page
1/32
Next page
23 08/237038-227L
Figure 23.2
4
1
1
1
1
6
Baffle Boards
Ceramic Blanket
Baffle Protection Channel
Brick Retainers
Right Side
Rear Brick
Side Brick
Tube Channel Assembly
Tube Channel Nuts X3
Bolts X3
1
2
4
3
Rotate and
remove from
firebox
F. Tube Channel Assembly Replacement
Service Part: SRV7038-008
Removing Tube Channel Assembly
1. Remove the right side shield by removing three (3)
Phillips screws from back of appliance; then pull back
of side out and push back on side.
2. Remove four (4) Phillips screws from channel access
cover and remove cover.
3. Locate three (3) channel nuts inside of chamber and
remove using a 7/16 socket wrench (Figure 23.2).
4. Inside of rebox, remove the right ve (5) side bricks
and one (1) right rear brick (Figure 23.2).
5. Remove the two (2) brick retainers by sliding back and
then up (Figure 23.2).
6. Remove the bafe protection channel by rolling forward
and out of the rebox (Figure 23.2).
7. Remove three (3) bolts from inside re box
(Figure 23.2).
NOTE: Soak the bolts with penetrating oil for at least 15
minutes before trying to remove them.
Ensure manifold tube gasket is placed
between rebox and manifold tube assembly
during re-installation process.
CAUTION
Replacing Tube Channel Assembly
8. Slide the tube channel assembly to the left. Drop the
right side down, then slide the assembly back to right.
9. The ceramic blanket and both bafe boards can
be removed at the same time you remove the tube
channel assembly.
10. When the tube channel assembly is free of the left side
support, rotate clockwise and pull assembly, blanket
and bafes out through the front opening.
11. Re-install in reverse order.
Figure 23.1
E. Door Handle Assembly
Service Parts: SRV7033-071
1. Slide door handle through door.
2. Install additional washer(s) as shown in Figure 23.1
3. Install key in groove.
4. Align groove in latch cam with key; slide latch cam
over shaft
5. Install locknut but do not over tighten, the handle needs
to rotate smoothly.
6. Install ber handle (Figure 23.1).
Locknut
Latch Cam
Spacing
Washers
Door Cross
Section
Square Key
Door Handle Shaft
Fiber Handle
Do not over tighten lock nut. The door handle needs to
move smoothly.
CAUTION!
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire 5700 Step Top at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire 5700 Step Top in the language / languages: English as an attachment in your email.

The manual is 6.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire 5700 Step Top

Quadra-Fire 5700 Step Top User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info